Carbon nanotube oscillators encapsulating copper nanowire were investigated by molecular dynamics simulations. The excess forces due to the carbon-carbon van der Waals interactions are higher than the excess force due to carbon-copper interactions. And the masses of copper atoms are higher than those of carbon atoms. So, the carbon atoms are easier accelerated than the copper atoms. When the encapsulated copper nanowire deforms the encapsulating nanotube, the frequency can not be estimated by the mass-frequency dependence in classical oscillation theory.

Phase transition and dopant redistribution during silicidation of $CoSi_2$ thin films were characterized depending on their preparation methods. Our results indicated that cleanness of the substrate surface played an important role in the formation of the final phase. This effect was found to be reduced by addition of W resulting in the formation of $CoSi_2$. However, even in this case, the formation of the final phase was achieved at the cost of extra thermal energy, which induced rough interface between the substrate and the silicide film. As for the dopant redistribution, the deposition sequence of Co and Si on SiGe was observed to induce significant differences in the dopant profiles. It was found that co-deposition of Co and Si resulted in the least redistribution of dopants thus maintaining the original dopant profile.

As preparing electrode for the OLED with the sputtering process, in order to be lower damage of the bottom organic layer and increase the life-time of the OLED, we prepared Al electrode for that by using Facing Targets Sputtering (FTS) system. Al electrode directly deposited on the cell (LiF/EML/HTL/Bottom electrode). Deposition condition was the working gas (Ar, Kr and Ar+Kr) and working gas pressure (1 and 6 mTorr). The film thickness and I-V curve of Al/cell were evaluated by a $\acute{a}$-step profiler and a semiconductor parameter (HP4156A) measurement. The thin film surface image was observed by a Atomic Force Microscope (AFM). In result, in comparison with about 11 [V] of the turn-on voltage of Al/cell with using the pure Ar gas, when Al thin film was deposited using the Ar-Kr mixture gas, the surface morphology was improved in some region and the turn-on voltage of Al/cell could be decreased to about 7 [V].

Vibration isolation equipments are mostly required in precise measurement and manufacturing system. Among all the vibration isolation equipments, air-spring is the most widely used equipment because of low resonant frequency and high damping ratio. In this study, we used Takagi-Sugeno fuzzy method to design an active vibration isolation system using air-spring, and compared the fuzzy method with passive control method and PID control method. Due to the non-linearity characteristics of air-spring, fuzzy controller was verified to be the most effective both in simulation and experiment.

Rotary stages in semiconductor, display industry and many other fields require challenging accuracy to perform their functions properly. Especially, Axis of rotation error on rotary system is significant; such as the spindle error motion of the aligner, wire bonder and inspector machine which result in the poor quality products. To evaluate and improve the performance of such precision rotary stage, undesired movements on the other 5 degrees of freedom of the rotary stage must be measured and analyzed. In this paper, we have measured the three translations and two tilt motions of the worm gear type spindle with high precision capacitive sensors. To obtain the radial error motion, we have used Donaldson's reversal technique. And the axial components of the spindle tilt error motion can be obtained accurately from the axial direction outputs of sensors by Estler face motion reversal technique. Further more we have designed and developed the sensor mounting jig with standard cylinder for reversal method.

Zinc gallate, $ZnGa_2O_4:Mn^{2+}$ co-doped with different concentrations of $Mg^{2+}$ (0.001- 0.5 mol%) was prepared by solid state synthesis method. These compositions were investigated for their photoluminescence and cathodoluminescence properties. The optimized composition $Zn_{0.990}Mg_{0.005}Ga_2O_4:Mn_{0.005}$ shows higher luminescence intensity compared to the parent phosphor. The intense green emission peak was found at 504 nm. The $Mg^{2+}$ doping does not affect much the decay time. It remains <10 ms for these compositions which make them potential candidate for application in TV screens.

Quartz glass panel was prepared by a colloidal silica through the heat-treatment only without any additives in wet-chemical method. This colloidal silica used in slurry process has the uniform distribution of particle size and lower cost. The results show that 6N as a degree of purity and the 86 percentage of violet transmittance in 1mm thickness. AFM(Atomic Force Microscopy) pattern shows that the surface roughness are less than lnm. Also, we investigated the characteristic of quartz panel according to the concentration and distribution of hydroxyl group, viscosity and thermal expansion coefficient.

Temperature distribution of the circular heat source was studied by analyzing the heat transfer of the environment of the circular source for OLED. Circular nozzle source was used to fabricate thin organic layer as the organic material in it was heated, vaporized and deposited to the large size panel. A modified heater structure of circular source has been suggested. The results of numerical analysis shows that the modified heater structure can use 15% more powder in a batch than the original heater structure does. Moreover, the modified heater structure can improve the uniformity of organic vapor deposition by controlling the temperature.

In this paper, we propose a novel sensor system for measuring the arterial pulse in an oral cavity. In order to measure pulse wave in oral cavity, the proposed system is designed with reflection type arterial wave sensor, not by using transmission type arterial pulse wave sensor. Driving circuit through pulse current is designed for solving self-heating problem of LED. The effectiveness of the proposed sensor system is compared with pulse wave between pulse wave of oral cavity and other body parts as well as with characteristic measurements. The experiment shows that the proposed sensor system is adaptive to capturing consecutive and meaningful biometric signals through the variation of pulse wave changes in oral cavity when exercising. The study result expects to design and develop mobile sensors which could be adapted to healthcare devices.

As the minimum feature size decrease, control of contamination by nanoparticles is getting more attention in semiconductor process. Cleaning technology which removes nanoparticles is essential to increase yield. A reference wafer on which particles with known size and number are deposited is needed to evaluate the cleaning process. We simulated particle trajectories in the chamber by using FLUENT. Charged monodisperse particles are generated using SMPS (Scanning Mobility Particle Sizer) and deposited on the wafer by electrostatic force. The Experimental results agreed with the simulation results well. We calculate the particles loss in pipe flow theoretically and compare with the experimental results.

In paper, We evaluated for various diode type ESD protection device using TLP measurement method. An Evaluation diode is divided to Enclosed type and Stripe type as pattern style in extensive. These diodes is split up followed factor that Anode-to-Cathod space, N+ region width, Multi type and Contact to Active space. After a TLP measurement, we can be got the Vt2, It2 by I-V characteristic values. In the results, diode of enclosed type is present relatively higher Current capability(It2) than stripe type in a same voltage conditions. And the Second-breakdown voltage(Vt2) were that Stripe type's diode higher than Enclosed type's diode as have $14{\sim}15V$. Finally we suggest the best diode design condition as ESD protection device using entire consequence.

The CNTs are the most extensively studied material which are characterized by the complete property of matter, structure, and the large thermal conductivity (thermal conductivity of CNTs ~>2000W/mK vs. thermal conductivity of Aluminum ~> 204W/mK). Thus, they are successfully applied to the various fields. However, due to the strong agglomeration caused by the van der waal's force, their applications are limited. In the present study, a new method for CNTs dispersion was developed by using the mechanical dispersion, acid treatment, and then Cu was coated. This process produces CNTs/Cu nanocomposite powders, whereby the CNTs are homogeneously located within the Cu powders. The electrical properties of the CNTs/Cu nanocomposite were investigated.

An epitaxial NiSi structure on Si (001) substrate was studied by using density functional theory (DFT). Orhorhombic and B2-NiSi structures were compared first. B2 structure was further considered as it has same crystal structure as Si and the lattice mismatch between B2 and Si is small, compared to orthorhombic-NiSi. The lattice parameters of x- and y-direction in B2-NiSi structure were modified to match with those in Si (001). The size reduction of the lattice parameter of B2-NiSi to match with that of Si increased the lattice parameter of z-direction by 10.5%. Therefore, we propose that an optimum structure of NiSi for epitaxial growth on Si (001) is a tetragonal structure.

The MIM(metal-insulator-metal) capacitors with the Al/PMMA/ITO/Glass structures were manufactured according to various PMMA concentration of 1, 2, 4, 6, 8 wt%. The lowest leakage current and the largest capacitance were found to be 2.3 pA and 1.2 nF, respectively, for the device with 2 wt% PMMA concentration. The measured capacitance of the devices was almost same values with the calculated one. The optimum film thickness was obtained at the value of 48 nm, showing that the capacitance and leakage current were 1.92 nF, 0.3 pA at 2 wt%, respectively. From this experiment, the PMMA gate insulator films can be applicable to the organic thin film transistors.