Silicide formation process and the formation sequence were investigated in this study. It was postulated that the formation of the second silicide phase involves glass formation between the first silicide phase and Si given that a thin metal film is deposited on a Si substrate. The concentration of glass was assumed to be located where the free energy of the liquid alloy with respect to the first nucleated compound and solid Si (${\Delta}$G') is most negative. It was also mentioned that the glass concentration is close to the composition of the second phase in order to achieve the maximum energy degradation. It was shown that the minimum ${\Delta}$G' concentration can be estimated by interpolating the portion of the liquidus where the liquid alloy is in equilibrium with the two solid constituents, namely the first compound phase and Si, thereby forming a hypothetical eutectic.

This paper proposed DC-DC converter for fuel cell that have high voltage and high current output characteristics. It is required step-up converter to use by general power supply, because the general rated voltage of fuel cell is low about 20$\sim$50V. The miniaturization of converter and DC link voltage can be controlled and high quality of output voltage uses mainly DC-DC converter. The boost converter and buck-boost converter do not get high boosting ratio. It is that proposed boost-flyback converter. Through simulation and an experiment, it could get high boosting ratio and efficiency more than 90%.

In this paper, in order to get the characteristics of the lithium secondary cell, such as charge and discharge characteristic, temperature characteristic, self-discharge characteristic and the capacity recovery rate etc, we build a thermal model that estimate the impedance of battery by experiment & simulation. In this one-dimensional model, Seven governing equations are made to solve seven variables c, $c_s,\;\Phi_1,\;\Phi_2,\;i_2$, j and T. The thermal model parameters used in this model have been adjusted according to the experimental data measured in the laboratory. The result(Voc, Impedance) of this research can be used in BMS(Battery Management System), so an efficient method of using battery is developed.

In this paper, the cell balance of secondary battery using a large number of MOSFETs is discussed. We can balance the cells by controlling battery charging current with help of MOSFETs. If the cells are not balanced, we can not use the whole energy of the battery while charging and discharging, therefore, the energy efficiency is decreased. To increase the energy efficiency, we propose the MOSFET control algorithm which will perform cell balancing by controlling the charging current.

Recently, regulation for THD (Total Harmonic Distortion) such as IEC 61000-3-2, IEEE 519 is being reinforced about a product which directly connects to AC line in order to prevent distortion of common power source in electronic equipment and electrical machinery. In order to satisfy these regulations, conventional circuits were used two-stage structure attached power factor correction circuit at ahead of converter but this method complicate the circuit and then a number of element increases thereupon the cost of production rises. in this paper, we propose a high efficiency single-stage 300W PFC fly-back converter that improved power factor and efficiency than conventional two-stage power module.

LCD panels are increasingly used to show moving image material, for example in LCD television sets. However, moving images become blurred on LCD panels. One of the causes of motion blur is the slow reaction of LC(liquid crystal) cell to change in the pixel value. Another cause of motion blur is the hold-type characteristic of the LCD panel, during the frame time the image is shown continuously. This type of motion blur can be reduced with a scanning backlight. We have designed and fabricated a scanning backlight system that solves the hold-type characteristic problem in a way that Flat fluorescent lamp divided 6 blocks was scanned 60Hz.

This study shows the improvement of PR-Ashing rates in semi-conductor process using Atmospheric Plasma. Taguchi method is used to improve Ashing rates of photo-resist that is spread on the surface of a wafer. Improvement of Ashing rates is acquired through the decision of the effective factors and suitable combination of the factors. The results show the contribution rate of each factor and the effectiveness of Plasma for PR-Ashing process in this system.

Productivity is one of the performance indices of the semiconductor equipment in manufacturing viewpoint. Among many ways tried and adopted for improvement of the productivity of the FAB equipment, variation of equipment configuration was considered and its effect on the throughput was analyzed. Parallel machine cycle charts that were generated based on the equipment log were used in the analysis. Efficiency of the equipment due to change of the structure and the probability of the usage in the manufacturing process were examined. The results showed that the modification of the control algorithm in the equipment and the redistribution of the process time for each process and transfer module along to the change in the structure enhance the throughput of the equipment.

An epitaxial $\beta-FeSi_2$ structure on Si (001) substrate was calculated by using density functional theory (DFT). Unit cell of orthorhombic $\beta-FeSi_2$ and $\sqrt{2}\times\sqrt{2}\times2$ supercell were calculated to find the energetically favorable structures first. The $\chi$- and y-direction axes of $\beta-FeSi_2$ were changed into y- and z-direction axes to match its structure with that of Si, to minimize the lattice mismatch between $\beta-FeSi_2$ and Si. Distance between the Si (001) surface and the $\beta-FeSi_2$ surface was varied to find an optimum distance between them, resulting in 0.825 $\AA$.

The yellow base polymer light emitting diodes(PLEDs) with double emission and hole blocking layers were prepared to improve the light efficiency. ITO(indium tin oxide) and PEDOT : PSS[poly(3,4-ethylenedioxythiophene) : poly(styrene sulfolnate)] were used as cathode and hole transport materials. The PFO[poly(9,9-dioctylfluorene)] and MEH-PPV[poly(2-methoxy-5(2-ethylhe xoxy)-1,4-phenylenevinyle)] were used as the light emitting host and guest materials, respectively. TPBI[Tpbi1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene] was used as hole blocking layer. To investigate the optimization of device structure, we prepared four kinds of PLED devices with different structures such as single emission layer(PFO : MEH-PPV), two double emission layer(PFO/PFO : MEH-PPV, PFO : MEH-PPV/PFO) and double emission layer with hole blocking layer(PFO/PFO : MEH-PPV/TPBI). The electrical and optical properties of prepared devices were compared. The prepared PLED showed yellow emission color with CIE color coordinates of x = 0.48, y = 0.48 at the applied voltage of 14V. The maximum luminance and current density were found to be about 3920 cd/$m^2$ and 130 mA/$cm^2$ at 14V, respectively for the PLED device with the structure of ITO/PEDOT : PSS/PFO/PFO : MEH-PPV/TPBI/LiF/Al.

The objective of the research is to design, manufacture and test a Mass Flow Controller(MFC) capable of measuring compressible fluid flows based on a "bucket and stop-watch"method. The basic principle is the measurement of time, where the time taken to fill and empty a bucket of known volume is measured. This method of flow measurement is a new concept when compared to a commercilized current mass flow controller. For the flow meter to be able to compete with established designs it not only must be comparable in cost and robustness, it must be very accurate and reliable as well. This device should be able to handle fluid flows in the range of 0.1ml/min to 10ml/min within an accuracy of ${\pm}$1%. A possible application for a device such as this is in electronics industry where arsenic gas is used in the production of silicon chips.

The Lifetime of OLEDs by ITO/glass substrates cleaning method and cathode deposition method were investigated in the fabrication of green light emitting OLEDs with $Alq_3$-C545T fluorescent system. In our experiments, the optimum cleaning method was obtained at last processing of boiling IPA(isopropyl alcohol). And the optimum deposition methode was obtained at 3 steps deposition rate of Al. The deposition rate of 3 steps progressed changing from $0.5\AA$/sec to $3\AA$/ sec. The green light emitting OLED with plasma treatment at 150W for 2 minutes showed the highest luminance and efficiency of 20000 cd/$m^2$ and 16 lm/W. On the contrary, the OLED device without plasma treatment showed much lower performance with the luminance and efficiency of 3500 cd/$m^2$ and 2 lm/W.

The MgO protective layer plays an important role in plasma display panels (PDPs). Our previous work demonstrated that the properties of MgO thin film could be improved, which were deposited by ion beam assisted deposition (IBAD). However arc discharge always occurs during the IBAD process. To avoid this problem, oxygen neutral beam assisted deposition (NBAD) is used to deposit MgO thin films in this paper. The energy of the oxygen neutral beam was used as the parameter to control the deposition. The experimental results showed that the oxygen neutral beam energy was effective in determining in F/$F^+$ centers, crystal orientation, surface morphology of the MgO thin film, and the discharge characteristics of AC PDP. The lowest firing voltage $(V_f)$ and the highest secondary electron emission coefficient $(\gamma)$ were obtained when the neutral beam energy was 300 eV.

Recently, as the multimedia processing application increases rapidly by going on increasing multimedia data, the efficient retrieval method of image information is required in many fields of application and becoming the matter of major concern. Furthermore, in the last few years rapid improvements in hardware technology have made it possible to process, store and retrieve huge amounts of data in a multimedia format. As a result, Content-Based Image Retrieval (CBIR) has been receiving widespread interest during the last decade. This paper propose the content-based retrieval system as a method for performing image retrieval through the effective feature analysis of the object of significant meaning by using YCbCr channel merging on the basis of the characteristics of man's visual system.