In this paper, the anode for molten carbonate fuel cell have been prepared by doctor blade method and microstructure, pore distribution, sintering test of the electrode were investigated. Component analysis were done by Scanning Electron Micrograph, porosimeter and sintering test apparatus. As a result, median pore size was 11.mu.m order at the major specimen and porosity was about 70%. And thickness loss of the electrode was 1.5% at Ni-10Co anode after sintering test.

For the observation of treeing, a visual measurement with an optical microscope has been used to explain breakdown mechanism in high-voltage systems. The conventional directed visual method of tree aging observation is difficult to measure in short time processing, and it is impossible to analyze on tree degradation area, progressed direction, tree pattern, etc. By using an image processing technique, the tree features which appear immediately after the tree initiation as well as changes in the configuration of the tree can be easily measured and observed than using the conventional visual methods. In this paper, we have developed a tree observating system by using image processing for tree growth, degradation area and other treeing progress. As an experimental result, it can be concluded that the image processing method is a more effective alternative than directed visual observation method. As a matter of fact, it is possible to record the image of tree propagation immediately after its first appearance and explain the characteristics of tree growth froth the computer processing image.

Dynamic characteristics of TbFeCo magneto-optical recording media at 680nm wavelength region were studied by means of computer simulation of disc structure and optimization of process variables during sputter deposition. With the slightly reduced Kerr rotation angle due to the reduced wavelength of optical laser source, the improved recording density in TbFeCo magneto optical media showing the CNR greater than 50dB could be achieved by only adjusting the thickness of dielectric and the recording layers when the wavelength of light source is changed from 780nm to 680nm. In addition, the recording power margin of 5mW and the 2mW minimum recording power was realized, It was shown from the present study that the increase in laser power density demonstrated feasibility of low cost and low power laser diode with the reduced optimum recording power.

This paper deals with the arc discharge characteristics of kerosene oil as a basic study on electrical discharge machine. Using needle electrode the discharge voltage, discharge current, discharge energy and the shape of discharge crater are measured. In consequence, it becomes clear that the discharge crater(depth, height, diameter) is depending on the discharge energy. Rapid increase in depth, height and diameter of discharge crater was observed during initial discharge, where discharge energy is large. However, rather slow decrease of those values was found when discharge energy is low or N is more than 3. As the ratio of $I_p$$T_on$ increase, the shape of discharge crater gets near circle. The protuberances of the discharge crater were not formed by the melted needle electrode but by the that of work piece.

Most of conventional ultrasonic transducers are constructed to generate either longitudinal or shear waves, but not both of them. We investigate the mechanism of dual mode transducers that generate both of the longitudinal and shear waves simultaneously with single PZT element. The study is aimed to find the optimally desired cut by examining the anisotropic piezoelectric properties. Theory predicts that a mixed P/S mode transducer can be constructed using a rotated Z-cut of PZT piezoelectric ceramics. We study the performance of a PZT element as a function of its rotation angle so that its efficiency is optimized to excite the two waves as much as equally strong. The results are verified by the waveform in pulse-echo computer simulation and experiments. When the transducer is subjected to impedance analysis, it shows two thickness mode resonances, each of which being a mixed P/S thickness mode. By examining wave speeds on E transmitter delay line receiver setup, it is confirmed that the transducer can transmit and detect both longitudinal and shear wave simultaneously.

최근 커패시터의 전극은 Pt, Au등으로 이용되고 있다. 이러한 전극의 전기적 특성은 우수하나 고가이다. 본 연구에서는 전극의 저가격화 측면에서 알루미늄 전극 위에 BaTiO$_{3}$를 증착하고 기관의 온도를 실온에서 600[.deg. C]까지 변화시켜 RF스퍼터링법으로 제작하였다. BaTiO$_{3}$세라믹의 유전특성은 구성하고 있는 입자의 강유전 분역 밀도와 입자의 크기에 의존하므로 입자가 성장되는 온도영역에서 입자의 크기와 유전율간의 관계를 연구하였다. 또한 BaTiO$_{3}$박막 커패시터의 유전상수는 BaTiO$_{3}$세라믹과 알루미늄기관의 계면에서 산화특성이 일어나기 때문에 기관온도의 변화에 의해 조사되었다. 기관의 온도를 증가시킴에 따라 결정면의 피크와 강도는 증가하였으며, 유전특성은 결정입자의 크기가 0.8[.mu.m]일때 가장 양호하였다. 유전율값은 기판 온도가 400[.deg. C]일 때 가장 크게 나타났다. 결과적으로, 알루미늄 전극에 BaTiO$_{3}$세라믹을 증착하여 저가의 적층용 세라믹 콘덴서를 제조할 수 있음을 알았다.

Silicone oils used insulating substances exhibit the both of organic and inorganic properties, and it has many superior characteristics such as the high thermal resistance and low thermal oxidation level when compared to other insulation oils. In order to investigate the dielectric loss due to the increase of viscosity, silicone oils of viscosity 1, 2, 5[cSt] had been chosen as the specimen and experiment has been performed in the temperature range of -70[.deg. C] - 65[.deg. C] and frequency range of 30 - 1*10$\^$5/[Hz]. As a result, the linear decrease of loss at low frequency region in high temperature was due to the influence of applying frequency, whereas the increase of loss at high frequency region was contributed by electrode's resistance. And increasing viscosity, the activation energy increased from 3.77[kcal/mole] to 7.21[kcal/mole]. The dipole moment of specimen was become clear 1.48 - 2.26[debyel in high temperature region(5 - 65[.deg. C]) and 1.05 - 1.80[debye] in low temperature region (-70 - -25[.deg. C])respectively.

Dielectric properties at microwave frequencies of ($Zr_{0.65}$, $Sn_{0.35}$) $Ti_{1.04}$ $O_{4.04}$ ceramics with additives, NiO as an agent to improve dielectric properties and $B_{2}$ $O_{3}$ as a firing agent were investigated. When 0.5 - 1.5 wt% of NiO is add, the grain growth is inhibited and the shape of the grain is uniformed, Dielectric constant(Fr) and bulk density are increased with raising amount of NiO at sintering temperature of 1330 - 1360.deg. C, but the temperature coefficient of resonant frquency(.epsilon.$_{r}$) decreased gradually as the NiO content increased. The value of Qx $f_{o}$ was increased as the amount of NiO was increased in the range of 0.5 to 1.0 wt% and the Qx $f_{o}$, was decreased slightly with raising sintering temperature. With NiO of 1.0 wt% and at sintering temperature of 1360.deg. C, this ceramics was found to have excellent microwave properties of .epsilon.$_{r}$=37.8, Qx $f_{o}$ = 48.600 and .tau.$_{f}$ = 7 ppm/.deg. C.C.. C.. C.C.. C.. C.

This study was concerned, after the oxide films(50 [.angs.]) were grown in a furnace and the MOS capacitor fabricated, with experimental comparison and verification about the Interference Effect of Electronic Waves in the ultra thin oxide/silicon interface. The average error was about 0.8404[%] in n'gate/p-sub and about 0.2991[%] in p$^{+}$gate/p-sub. Therefore, it was predicted that the Interference Effect of Electronic Waves can overcome somewhat according to the gate polarity.

In this study, Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_{3}$ ceramic thin films were fabricated from an alkoxide-based by Sol-Gel method. Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_{3}$ stock solution was made and spin-coated on the Pt/ $SiO_{2}$/Si substrate at 4000[rpm] for 30[sec.]. Coated specimens were chied at 400[.deg. C] for 10[min]. The coating process was repeated 6 times and then heat-treated at 500-800[.deg. C] and 1 hour. The final thickness of the thin films were about 4800[.angs.]. The ferroelectric perovskite phases precipitated under the sintering of 700[.deg. C] for 1 hour. Pb(Z $r_{0.52}$ $Ti_{0.48}$) $O_{3}$ thin films sintered at 700[.deg. C] for 1 hour showed good dielectric and ferroelectric properties.

The (Sr$_{1-x}$ .Ca$_{x}$)TiO$_{3}$+0.6[mol%]Nb$_{2}$O$_{5}$ (0.05.leq.x.leq.0.2) ceramics were fabricated to form semiconducting ceramics by sintering at about 1350[.deg. C] in a reducing atmosphere(N$_{2}$ gas). Metal oxides, CuO, was painted on the both surface of the specimens to diffuse to the grain boundary. They were annealed at 1100 [.deg. C] for 2 hours. The 2nd phase formed by thermal diffusing from the surface lead to a very high apparent dielectric constant. According to increase of the frequency as a functional of temperature, all specimens used in this study showed the dielectric relaxation, and the relaxation frequency was above 106 [Hz], it move to low frequency with increasing resistivity of grain. The specimens showed three kinds of conduction mechanisms in the temperature range 25-125 [.deg. C] as the current increased: the region I below 200 [V/cm] shows the ohmic conduction. The region rt between 200 [V/cm] and 2000 [V/cm] can be explained by the Poole-Frenkel emission theory, and the region III above 2000 [V/cm] is dominated by the tunneling effect.fect.

Polycrystalline CdTe thin film has been studied for photovoltaic application due to the 1.45 eV band gap energy ideal for solar energy conversion and high absorption coefficient. The formation of low resistance contact to p-CdTe is difficult because of large work function(>5.5eV). Common methods for ohmic contact to p-CdTe are to form a p+ region under the contact by in-diffusion of contact material to reduce the barrier height and modify a p-CdTe surface layer using chemical treatment. In this study, the surface chemical treatment of p CdTe was carried out by H$\_$3/PO$\_$4/+HNO$\_$3/ or K$\_$2/Cr$\_$2/O$\_$7/+H$\_$2/SO$\_$4/ solution to provide a Te-rich surface. And various thin film contact materials such as Cu, Au, and Cu/Au were deposited by E-beam evaporation to form ohmic contact to p-CdTe. After the metallization, post annealing was performed by oven heat treatment at 150.deg. C or by RTA(Rapid Thermal Annealing) at 250-350.deg. C. Surface chemical treatments of p-CdTe thin film improved metal/p-CdTe interface properties and post heat treatment resulted in low contact resistivity to p-CdTe.Of the various contact metal, Cu/Au and Cu show low contact resistance after oven and RTA post-heat treatments, respectively.

In this paper, The effect of the impedances in SNOSFET's memory devices has been developed. The effect of source and drain impedances measured by means of two bias resistances - field effect bias resistance by inner region, external bias resistance. The effect of the impedances by source and drain resistance shows the dependence of the function of voltages applied to the gate. It shows the differences of change in source drain voltage by means of low conductance state and high conductance state. It shows the delay of threshold voltages. The delay time of low conductance state and high conductance state by the impedances effect shows 3[.mu.sec] and 1[.mu.sec] respectively.

Dropouts in magnetic media are a primary quality deficiency which is detrimental to magnetic signal quality and thus the major impediment to error-free recording, especially in high density digital recorders. The specific form of defects and causes found to be responsible for signal dropouts occurring in magnetic tape were studied. Dropout occurred when the RF signal falls to low level due to the various types of surface defects. However, the fall in the level of the RF signal in gravure roll coated tapes was most often caused by foreign particles adhering to the magnetic tape. It was also shown from the present study that scattered particles trapped under the tape surface or put on the top can lift it as it crosses the head, creating a spherical tent shaped defect and causing a temporary signal drop. Dropout producing substances were identified through optical and microchemical analyses. The results were correlated with measured electrical signal losses combined with analytical microscopy to clarify source identification of defects.

In this study, the BaTiO$\sub$3/ capacitor add to MnO$\sub$2/ like depressor and shifter were investigated for temperature or voltage compensation by structural and electrical analysis. The relative density of BCTM, generating poly crystall and formation of lattice defect, has a 90[%] over as the CaTiO$\sub$3/ come out to control grain size. The current density of BCTM2 increased non-ohmic in high-electric field but that BCTM3 and BCTM4 had a few changing. The BCTM3 and BCTM4 unformated grain boundary shown temperature compensation properties, so that the dielectric constant was low value. The curie point was near 140[.deg. C] in BCTM1 and BCTM4, but BCTM3 and BCTM4 not shown the curie point. It is found that the charging energy of BCTM4 was changed 6[%] according to rising temperature from room temperature to 417[K]. The formation of BaMnO$\sub$3/ was low dielectric constant to change frequency and temperature.

정보처리의 다양화, 고속화를 위하여 장래의 집적회로는 다량의 정보를 단시간에 처리하지 않으면 안된다. 종래, 3년에 4배의 고집적화가 실현되어 LSI개발에 기술 견인차의 역할을 하고 있는 DRAM(Dynamic Random Access Memory)은 미세화기술의 한계를 우려하면서도 오히려 개발에 박차를 가하고 있다. 이러한 DRAM의 미세, 대용량화에는 미세가공 기술, 새로운 메모리 셀과 트랜지스터 기술, 새로운 회로 기술, 그 이외에 재료박막기술, Computer aided design/Design automation(CAD/DA) 기술, 검사평가기술 혹은 소형팩키지(package)기술등의 광범위한 기술발전이 뒷받침되어 왔다. 그 중에서 미세가공 기술 및 새로운 트랜지스터 기술과 메모리 셀 기술을 중심으로 개발 동향을 살펴보고 최근에 발표된 1Gbit DRAM의 시제품 기술에 대하여 분석해 보기로 한다.

전자재료라 총칭하는 재료의 종류는 셀 수 없을 정도로 많다. 대표적인 전자재료로는 반도체재료를 들 수 있으며 다음으로는 전기광학 소자의 재료로 쓰이는 여러가지 광학용 단결정, 그리고 저항이나 축전지 등의 제조에 사용되는 여러가지 재료들도 이에 포함된다. 이러한 전자재료의 특성을 평가하는 방법도 여러가지 있겠으나 여기에서는 그 범위를 임의로 반도체레이저의 제조에 사용되는 화합물반도체에 국한시켜 각 공정별로 이떠한 평가방법이 사용되는지, 그리고 각각의 특성평가 방법에 대하여 간략하게 알아보기로 한다.