ZnO films have been grown easily with the conventional thermal evaporation method on SiO$\_$2/ coated Si wafers. Anhydrous zinc acetate has been used as evaporation source. Zinc-acetate was directly heated in the laboratory-made brass boat. Zinc-acetate was sublimed at the boat temperature of about 220.deg. C. The substrates were heated to 600.deg. C with home made tantalium heater. Oxygen has been flowed into the deposition chamber to change the partial pressure of oxygen. X-ray diffraction patterns showed all the films to be amorphous. The films deposited at high oxygen pressure exhibit higher resistivity than films at low pressure. Energy dispersive spectroscopy(EDS) and rutherford backscattering spectrometry(RBS) were conducted on the films to reveal the composition of the ZnO films.

A n-CdS thin films were evaporated by thermal evaporation method and their structure, optical transmission spectra and electrical characteristics were investigated. The photovoltaic characteristics of solar cells which were fabricated in optimum conditions measured. The evaporated CdS thin films showed in hexagonal structure and above 80% of optical transmission spectra regardless of impurity doping. The high quality thin films could be obtained at 150.deg. C temperature of substrate, which is useful for solar cell window layer with low resistivity of 6*10$\^$-2/(.ohm.-cm) by In doping We measured the electrical and optical characteristics of the n-CdS/p-InP heterojunction solar cells. The most efficient photovoltaic characteristics of heterojunction solar cells had the open circuit voltage of 0.66V, short circuit current density of 13.85mA/cm$\^$2/, fill factor of 0.576 and conversion efficiency of 8.78% under 60mW/cm$\^$2/ illumination.

In order to elucidate the electrical and mechanical properties of insulating paper, it is desirable to study the performances of tensile strength, dielectric constant, dielectric strength. In this work, we constructed the characteristics depending on change of fabrication condition, and these specimens were manufactured by hot press method. As a result, tensile strength was about 75MPa and breakdown was above 5 kV/mm at the minimum value.

The surface of GaAs was treated by using the 0.1M solution of N $a_{2}$S.9 $H_{2}$O. The passivation of the surface in this sample was investigated by the photoreflectance(PR) experiment. The surface electric field( $E_{s}$) and built-in voltage( $V_{bi}$ ) discussed from Franz-Keldysh oscillation of PR signals. The density of surface states and Fermi level of GaAs treated with N $a_{2}$S.9 $H_{2}$O for 40min were determined 1.61*10$^{12}$ c $m^{-2}$ and 0.73eV. These values were about 15 and 10% smaller than those in untreated sample.e.

Effect of boron in GaAs have been investigated by photo induced current transient spectroscopy(PICTS). The starting material was undoped liquid encapsulated Czochralski(LEC) semi insulating GaAs and boron ion implantation at 150keV energy was conducted with dose of 10$\^$12/ and 10$\^$13/ions/cm$\^$2/. In ion implanted samples, the peaks related arsenic vacancy(V$\_$As/) were decreased but complex lattice defect was increased with annealing temperature. U band was observed at ion implanted(10$\^$13/ ions/cm$\^$2/) and thermally treated(550.deg. C) sample. More negative peak was detected after annealing at temperature between 600 and 700.deg. C. The measurement of dark current showed that the formation of B$\_$GA/-V$\_$As/, complex defect and complex lattice defect by ion implantation were a reasonable explanation for the decrease in dark current.

To improve dielectric and mechanical properties of insulating composite by plasma surface treatment, new plasma surface treatment process is designed with concentric and hemi-circle electrodes system. the plasma, which is generated between anode and cathode, is induced to the upper side of the electrode system and treats the surface of the insulators. The optimal surface treatment condition is that pressure : 0.5[torr], flux density : 100[gauss], discharge current : 500[mA] and treatment time : 3 minutes. The composite filled with glass cloth surface-treated by plasma shows the improvement in electric and mechanical properties, comparing non- and coupling agent treated samples.

A directional coupler which on the X-cut $LiNbO_3$ substrate is fabricated by using proton exchange method and self-aligned method. After proton exchange process, the waveguide is formed by annealing process. The relation ship between refractive index change of waveguide and maximum output was studied along with the annealing time. A self-aligned method was used to simplify the fabrication process of the waveguide and to maximize the efficiency of electric field. The on-off state of modulator has been observered with the switching of the directional coupler by the electric field effect and also the switching voltage of the directional coupler has been measured with 8.0 [V].

Most important study on development of high-Tc superconducting magnet is magnetic properties with design conditions To study optimal design condition of high-Tc superconducting magnet, small size solenoid magnet was designed and simulated. Design conditions are radius of bobbin, radius of magnet, length of magnet, critical cur-rent and notch size. We know that intensity of magnetic fields was controled by critical current and uniformity of magnetic fields was controled by notch size. The optimal design conditions to get the high intensity and uniformity of magnetic field in this experiments were radius of bobbin=3[cm], radius of magnetic=12[cm], length of Z=10[cm], notch size=6[cm] and critical current=12[A].

The optical and electrical properties of $C_{22}$-Quinolinium(TCNQ) Langmuir-Blodgett films have been studied depending on the annealing temperatures. The optimal properties were investigated using UV/visible(300-800[nm]) absorption spectra and FTIR(Fourier-transformed- infrared) absorption measurements. The electrical properties were investigated in a frequency range of 10[Hz]-13[MHz]. The UV/visible absorption spectra at room temperature show that there are four characteristic peaks at 320, 380, 494 and 678[nm]. These absorption peaks decrease very rapidly above the annealing temperature of 180[.deg. C], which is due to a structural change of TCNQ. The FTIR absorption measurements strongly support the result of the UV/visible absorption spectra, because the absorption peak of TCNQ- at 2181[$cm^{-1}$ /] also decreases above 140[.deg. C]. The frequency-dependent dielectric constant shows that there is a dielectric dispersion near 1[MHz] which is due to an orientational polarization of the molecules inside the film. The overall frequency-dependent dielectric constant is higher near 80[.deg. C]. It may be due to a softness of the alkyl chains.s.

메그네트론 스퍼터링으로 제작한 고밀도 다층박막($Co_75{{Pt_12}{Cr_13}}$합금) 디스크를 투과전자현미경을 이용해 단면 및 평면의 미세조직의 조사 혹은 미소부위 성분분석을 할 경우, 선행되어야하는 시편준비 경로와 각 단계별 구체적방법 및 그 효과를 연구하였다. Ion밀링시간이 증가함에 따라 시료가 얇게 되는과정에서 스퍼터링된 물질이 관찰될 시편부위의 다른 표면에 증착되므로써 미세조직의 선명도를 해칠 수 있고, 이로인한 해석상의 오류가능성이 시사되었다. 또한, 자기박막 디스크와 같이 다층으로 구성된 단면분석용 시료에서는 서로 맞붙인 실리콘 단결정 접착면을 따라 밀링속도가 선택적으로 커서 우선축이 생김으로써 양질의 시편을 얻기 어려운 문제점이 제기되었다. 이같은 문제를 포함한 전자현미경 시료준비과정에서 생길 수 있는 문제를 해결할 수 있는 실마리와 이를 이용해 수행한 전자현미경 분석결과 및 효과적인 시편준비방법이 본 논문에서 언급되었다.

The degree of the photodoping process in Ag(100[.angs.])/a-Se$_{75}$Ge$_{25}$(1500[.angs.]) films has measured as a function of the photon energy between 1.5[eV] and 2.9[eV] with the exposing time. The "window" characteristics of Ag occur at 3400[.angs.] (3.65[eV]) and Ag is almost transparent in this region. It is shown that transmittance is almost constant (40-50%) for the wavelength ranges of our experiment. It is found that the energy gap of a unexposed a-Se$_{75}$Ge$_{25}$ film is 1.81[eV]. Ag photodoping process results in the photodarkening effect which the absorption edge shifts to the long wavelength. Especially, very large band shift (-0.3[eV]) is obtained by exposing He-Ne laser(6328[.angs.]).. We have obtained "the U-type property" for Ar He-Ne and semiconductor laser. It is associated with the variation of energy gap(E$_{g}$) with photo-dose and substantially is explained by DWP model.l.gap(E$_{g}$) with photo-dose and substantially is explained by DWP model.

Cu/NbTi multilayer thin films and superconducting wires were fabricated and heat treated with conventional annealing and analyzed by differential scanning calorimetry (DSC) as a basic study for the enhancement of Jc. Interfacial reactions of Cu/NbTi multilayer thin films and superconducting wires were investigated with optical microscope, SEM, and XRD. According to the effective heat of formation (EHF) model, CU$\_$3/Ti was predicted as a first phase. However, considering the crystalline structure and thermodynamics, CuTi was predicted as a first phase. According to the results of DSC and XRD, CU$\_$2/Ti was found to be the first phase, followed by the formation Of CU$\_$4/Ti. The difference in first crystalline phase between the experimental result and the predicted one was discussed. In case of Cu/NbTi superconducting wires, the compounds formed at the Cu/NbTi interface grew with annealing time and the amount of compounds formed in Nb-47wt%Ti alloy was larger than that in Nb-50wt%Ti alloy. It seemed that the incubation time for the formation of compounds in Nb-50wt%Ti alloy was longer than that formed in Nb-47wt%Ti alloy. Also, the diffusion was the rate controlling step for the growth of compounds in all specimens. These compounds were formed at 500-600.deg. C for I hour annealing and, thus, the drawing time below I hour must be required to minimize the growth of compounds for the enhancement of Jc.

The purpose of this study is to research and develop solid polymer electrolyte(SPE) for Li secondary battery. We investigated the effects of lithium salts, plasticizer addition, temperature dependence of conductivity and electrochemical stability window of polyethylene oxide(PEO) electrolytes. PEO electrolyte completed with LiCIO$\_$4/ shows the better conductivity than the others. PEO-LiCIO$\_$4/ electrolyte, when EO/Li$\^$+/ ratio is 8, showed adequate conductivity around room temperature. By adding propylene carbonate and ethylene carbonate to PEO-LiCIO$\_$4/ electrolyte, its conductivity was higher than that of PEO-LiCIO$\_$4/ without those. Also PEO$\_$8/LiCIO$\_$4/ electrolyte remains stable up to 4.5V vs. Li/Li.

As lengthen gap leng of artificial needle shape void 0.24.rarw.1.5[mm]), the amplitude of AE(Acoustic Emission) pulses was enlarged and number of pulses be generated was few. The longer gap length of void, the shorter breakdown time. As a result of this, I found that existen of void in insulation mate was fatal deterioration of insulation. According to phase angle of applied voltage, time being void was scattered largely in region of phase angle of pulses of origination in phase angle of applied voltage. The result will be used to analysis of void diagnosis.

The purpose of this research is to study on characteristics of corona ignitor which was designed for ignition of plasma, used at hard coating, surface treatment and thin film preparation, at high pressure. Corona ignitor composed of hollow type inner electrode and ring type external electrode. Though corona voltage increased with increasing distance between electrodes, corona discharge can be controlled stably. The gas flow in hollow type inner electrode and the construction between electrodes affect a length of corona flame and corona phenomenon. It is possible to ignite the . plasma, usually generated at low pressure(10 Torr), at high pressure(100 Torr) by corona ignitor.

본 고에서는 Nb$_{3}$Sn 초전도선재의 대표적인 제조방법 및 원리 그리고 고자장마그네트 설계시 중요한 요소인 Nb$_{3}$Sn의 자장중 초전도특성 및 기계적특성 등에 대하여 고찰하고자 한다. 또한 Nb$_{3}$Sn 초전도선재의 응용분야로서 몇가지 대표적인 예를 들어 현재 세계적으로 활발하게 진행되고 있는 선진국의 고자장 초전도마그네트와 관련된 연구개발동향을 소개하고자 한다.