In this paper, we proposed that when combustible burn with ultraviolet radiation, introduce fire detector with sensor of private-use detectable light energy as ultraviolet in energy of electromagnetic-wave type radiate from flame. This research using ultraviolet flame sensor is pyro-electric ultraviolet sensor based black body radiation theory. To have high sensibility and to gain proper output voltage, it has high responsive performance. This research introduced UV flame detector and proposed method of false alarm reduced to resemble fire. the result proposed the prevention and extinction of fire technique degree, certificated operation of detector.

A 3D depth measurement system is proposed for mobile vehicles. Depth measurement system which is composed of a rotating mirror, a line laser and mono-camera is employed to detect depth, where the laser light is reflected by the mirror and projected to- the scene objects whose locations are to be determined. The obtained depth information is converted into an image. Such depth images of the road region represent even and plane while that of off-road region is irregular or textured. Road region is detected employing a simple spatial differentiation technique to detect the plain textured area. Identification results of the diverse situation of Non-linear trail are included in this paper.

In this paper, abnormal heating of circuit breaker in panel board by poor connection was studied. Firstly, calculation method of contact resistance shown in IEC 60943 was examined. Secondly, concerning abnormal heating of circuit breaker in panel board, field measurements were performed. Field measurements showed that locally abnormal heating by poor connection could be detected, therefore, in that case, immediate action was needed. Finally, experiments regarding abnormal heating between terminal of circuit breaker and electric wire were conducted. The results showed that abnormal heating above $180^{\circ}C$ was measured. Also, in the results of analysis of electrical waveforms according to load current, voltage drop occurred around poor connection, and the oxide was generated according to mechanical vibration. In order to prevent electrical disaster caused by poor connection, adequate torque should be applied to electrical connection, and periodic check-ups are needed.

$CuInS_2$ thin films were synthesized by sulpurization of Cu/In Stacked elemental layer deposited onto glass Substrates by vacuum furance annealing at temperature 200[$^{\circ}C$]. And structural and electrical properties were measured in order to certify optimum conditions for growth of the ternary compound semiconductor $CuInS_2$ thin films with non-stoichiometry composition. $CuInS_2$ thin film was well made at the heat treatment 200[$^{\circ}C$] of SLG/Cu/In/S stacked elemental layer which was prepared by thermal evaporator, and chemical composition of the thin film was analyzed nearly as the proportion of 1 : 1 : 2. Physical properties of the thin film were investigated at various fabrication conditions substrate temperature, annealing and temperature, annealing time by XRD, FE-SEM and hall measurement system. At the same time, carrier concentration, hall mobility and resistivity of the thin films was $9.10568{\times}10^{17}[cm^{-3}]$, 312.502[$cm^2/V{\cdot}s$] and $2.36{\times}10^{-2}[{\Omega}{\cdot}cm]$, respectively.

기존의 대부분의 안테나는 한정된 공간에서 한정범위의 인식이 곤란한 단점이 있었다. 이러한 단점을 개선하고 소형화를 위하여, 간단한 형태의 다이폴안테나를 설계 하였다. Ansoft사의 Designer를 이용하여 안테나 시뮬레이션을 수행 하였으며, 산업체의 자동화 공정이나, 컨베이어상에서 제품에 부착된 전자태그의 인식효율과 소형화를 고려하여 설계하였다. 설계한 안테나는 RFID 안테나의 소형화와 한정된 공간에서 Tag 의 인식을 위해 테프론 기판을 이용한 다이폴 형태로 구현 제작하였다. 본 연구결과 설계 제작된 안테나는, 도우넛형태의 방사패턴을 가지며, 협소한 지역에 전파를 방사시켜서, 주변의 불필요한 태그의 인식을 최소로 하였고, 실제로 컨베이어 장치를 이용하여 개발 제품의 성능 테스트를 수행하였으며, 그 결과 제품의 우수성을 검증 하였다.

In this paper, we developed a hybrid simulation model of carbon laser ablation under the Ar plasmas consisted of fluid and particle methods. Three kinds of carbon particles, which are carbon atom, ion and electron emitted by laser ablation, are considered in the computation. In the present simulation, we adopt capacitively coupled plasma with asymmetrical electrodes. As a result, in Ar plasmas, carbon ion motions were suppressed by a strong electric field and were captured in Ar plasmas. Therefore, a low number density of carbon ions were deposited upon substrate. In addition, the plume motions in Ar gas atmosphere was also discussed.

In this study, The new type of loop antenna which detects the partial discharge was designed based on microstrip line technology. In diagnosis of power cable, partial discharge signal generally occurred at the frequency range lower than 100MHz because high frequency PD signals could be lost along the propagation path in the cable. The new type of loop antenna sensor has been studied by using Simulation software named CST microwave studio version 5.0. In partial discharge measuring experiments, commercial HFCT sensor was used as a reference sensor. Several experiments were made over HFCT sensor and loop antenna sensor in detection partial discharge on MV XLPE cable of 22.9kV. In this study, we have shown our loop antenna sensor can apply as a commercial HFCT sensor.

Recently, due to the onset of the information age, various high-priced, large-size machines have been invented such as intelligent building and high-tech computer operated facilities. Consequently, all kinds of electrical, electronic, and communication equipments and facilities have been found to be vulnerable even to small amounts of electrical shock. Interference between equipments and equipment malfunction occur because of various electromagnetic interferences. Galvanic action by direct current (D.C.) causes gas valve corrosion and other electrical problems such as static electricity and electromagnetic interference (EMI) occur as well. Most of the problems stated above occur because of problems in grounding.

Al-doped ZnO (AZO) thin films have been fabricated by vertical in-line dc magnetron sputtering for transparent conducting oxides (TCOs) applications. The effects of substrate temperature and dc power on the characteristics of AZO thin films are investigated and also optimized the process conditions to get the best electrical and optical properties. The fabricated thin films show a good electrical and optical uniformity within ${\pm}5%$ over the whole area of substrate ($200mm\;{\times}\;200mm$) ; the minimum resistivity of $8\;{\times}\;10^{-4}\;{\Omega}cm$ and the average transmittance of 90% within the visible wavelength range. We have found that the band gap ($E_g$) increases with increasing substrate temperature and dc power, whereas the crystallinity is getting improved with increasing substrate temperature. The binding energy of Zn $2p_{3/2}$ and O 1s is observed to decrease as the substrate temperature increases.

In this study, we report an electrical properties of green OLEO, using the changed thickness of Al Layer. We investigated the electrical properties of OLEOs by IVL and optical properties by EL spectrum. The fundamental structure of green OLEOs was ITO anode/TPD($400{\AA}$)/$Alq_3(600{\AA})$)/LiF($10{\AA}$)/Al($200{\sim}600{\AA}$) cathode. The threshold voltage was low value according to the more thin Al layer. The luminance was increased by decreased cathode layer. The threshold voltage was 12V and wavelength was 530nm at $200{\AA}$ cathode.

Polyethylene is widely used as the insulator for power cable. To investigate the conduction mechanism for power cable insulation under ac high field, it is very important to acquire the dissipation current under actual running field. Recently, we have developed the unique system, which make possible to observe the nonlinear dissipation current waveform. In this system, to observe the nonlinear properties with high accuracy, capacitive current component is canceled by using inverse capacitive current signal instead of using the bridge circuit for canceling it. We have already reported that the dissipation currents of $40\;{\mu}m$ thick LDPE film at 10 kV/mm and over 140 Hz, it starts to show nonlinearity and odd number's harmonics were getting large. To investigate the conduction mechanis ms in this region, especially space charge effect, various kinds of estimation, such as time variations of instantaneous resistivity for one cycle, FFT spectra of dissipation current waveforms and so on, has been examined. As the results of these estimations, it was found that the dissipation current will depend on not only the instantaneous value of electric field but also the time differential of applied electric field due to taking a balance between applied field and internal field. Furthermore, two large peaks of dissipation current for each half cycle were observed under certain condition. In this paper, to clarify the reason why it shows two peaks for each half cycle, the film thickness dependences of dissipation current waveforms were observed by using the three different thickness LDPE films.

In this work, the $TiO_2$ pigment influence in HDPE dielectric strength was analyzed. Chemical and structural characterizations were made to identify changes during the processing and your influence in the electrical properties. Formulations containing 0, 0.5, 1, 2.5, 4 and 6 of titanium dioxide were processed by extrusion and injection molding with stabilization-antioxidants, ultraviolet stabilizers and plasticizers. The electrical strength tests were analyzed by the statistical distribution of Weibull, and the maximum likelihood method. The high concentrations present lower values to electrical strength. The $\beta$ parameter could be using to insulator particles dispersion. The $TiO_2$ concentration variation shows that these incorporations implicate strength values increase has a maximum (5,35MV/cm). High pigment concentration induces a little falls in property values. Observing the $\beta$ parameter, minimum experiment electric field (Ebmin) and electric strength value, found that the best electric perform formulation was the formulation with 2.5% $TiO_2$ weight.

A new modular Lateral Information Propagation Networks can be implemented in a IC chip with the circuit VLSI technology for detection of bad materials. The proposed modular architecture is propagated the neural network through inter module connections. For such inter module connections, the host(computer or logic) mediates the exchange of information among modules. Also border nodes in each module have capacitors for temporarily retaining the information from outer modules. For detecting of Faulty Insulator, $4\;{\times}\;4$ neural network modules has been designed and simulation of interpolation with the designed networks has been done.

$TiO_2$ is a wide band-gap semiconductor (3.4 eV) and can only absorb about 5% of sun light in the ultraviolet light region, which largely limits its practical applications because of the lower utility of sun light and quantum yield. In order to move the absorption edge of $TiO_2$ fims to visible spectrum range, we have made the impurity level within a band-gap of $TiO_2$ thin film by introduction of oxygen vacancy. Oxygen-defected $TiO_2$ thin film have prepared by reactive sputtering with the partial pressure of $Ar:O_2=10:90{\sim}99.33:0.66$ ratio. As a result, we could have the impurity level of about 2.75 eV on condition that oxygen partial pressure is below 7%.

Spacecrafts such as most of commercial satellites that are operating in the geostationary orbit can be subjected to intense irradiation by charged particles. The surface made of dielectric materials can therefore become probable sites for damaging electrostatic discharges. Thanks to a specially equipped chamber, the spatial environment can be reproduced experimentally in the laboratory. In this paper, the behavior of high energy electrons injected in polymers such as PolyMethylMetaAcrylate (PMMA) and Kapton is studied. Results obtained by surface potential technique, pulse-electro acoustic device and a cell based on the split Faraday cup system are analyzed and discussed.

Decay processes of accumulated charge in e-beam irradiated polymers during elevating temperature are observed using pulsed electro-acoustic measurement system. Since the polymeric materials have many superior properties such as light-weight, good mechanical strength, high flexibility and low cost, they are inevitable materials for spacecrafts. In space environment, however, the polymers sometimes have serious damage by irradiation of high energy charged particles. When the polymers of the spacecraft are irradiated by high energy charged particles, some of injected charges accumulate and remain for long time in the bulk of the polymers. Since the bulk charges sometimes cause the degradation or breakdown of the materials, the investigation of the charging and the decay processes in polymeric materials under change of temperature is important to decide an adequate material for the spacecrafts. By measuring the charge behavior in e-beam irradiated polymer, such as polyimide or polystyrene, it is found that the various accumulation and decay patterns are observed in each material. The results seem to be useful and be helpful to progress in the reliability of the polymers for the spacecraft.

In this paper, we have investigated dispersibility, volume resistivity of nano-composite by solution mixing method. Dispersibility measured by FE-SEM(Field Emission Scanning Electron Microscope. And volume resistivity measured by ASTM D991. To expect interaction used dual filler system. But, dual filler system had influence on polymer complex. So, polymer chain mobility doesn't resist.

In this paper, we measured the activation energy of the Bisphenol A type Epoxy resin (DGEBA)-Jeffamine system according to an irradiation. We put the mixed solutions to the silicon mold after mixing both DGEBA(216g) and Jeffamine(93.9g), curing agent of amine system. The mixed solutions were cured in the atmosphere during 24hours after finishing the first curing during 4hours in the vacuum oven under $80^{\circ}C$. The mixed solutions were cured in the atmosphere during 24hours after finishing the second curing during 12hours in the vacuum oven under $60^{\circ}C$ again. Prepared samples were irradiated to the dose rate of 8kGy/hr with 500kGy, 700kGy, 1000kGy, 1500kGy, 2000kGy, 2500kGy. Experimental results indicated activation energy of the samples reduced as the irradiation dose increased because of the peroxides of the Epoxy created by the oxidation and the radiation.

In this paper, we have designed the Anti-Reflection (AR) coating for 850, 1310 nm(multi type) and 1310, 1550 nm(multi type) wavelength ranges on the ferrule facet of special optical connector. The reflectance of the AR coated ferrule facet is designed under 5% for 850, 1310 nm(multi type) and 1310, 1550 nm (multi type). The average return loss of the AR coated ferrule facet is 47.1 dB.

Polyimide is widely used as a high-temperature insulating material. Space charge distributions in polyimide (PI) films strongly depend upon electric field, temperature, water content and so on. We observed space charge distributions in PI films with various water contents. When a dc field was applied to as-received PI films or water-treated PI films, positive and negative homo space charges were observed near the respective electrodes at 333 K. In dried PI films, the homo space charges were much reduced, and positive and negative hetero space charges in the bulk were clearly observed. The space charge amounts in water-treated PI films were smaller than in as-received ones, while the current density in water-treated PI film was larger than that in as-received one by two or more orders of magnitude. These suggest not only that the charge injection from the electrode is enhanced by absorbed water but also that absorbed water makes carriers mobile. The decay of space charge was also faster in water-treated PI than in as-received or dried one. This also supports the enhancement of apparent mobilities of carriers in PI by absorbed water.

$CuInSe_2$ thin film were prepared in order to clarify optimum conditions for growth of the thin film depending upon process, and then by changing a number of deposition conditions and heat treatment conditions variously, structural and electrical characteristics were measured. Thereby, optimum process variables were derived. For the manufacture of the $CuInSe_2$, Cu, In and Se were deposited in the named order. Among them, Cu and In were deposited by using the sputtering method in consideration of their adhesive force to the substrate, and the DC/RF power was controlled so that the composition of Cu and In might be 1:1, while the annealing temperature having an effect on the quality of the thin film was changed from $200^{\circ}C$ to $350^{\circ}C$ at intervals of $50^{\circ}C$.

Polymers submitted to thermo/electrical stress suffer from ageing that can drastically affect their functional behaviour. Understanding the physico/chemical processes at play during ageing and defining transport regimes in which these mechanisms start to be critical is therefore a prime goal to prevent degradation and to develop new formulation or new materials with improved properties. It is thought that a way to define these critical regimes is to investigate under which conditions (in terms of stress parameters) light is generated in the material by electroluminescence (EL). This can happen through impact excitation/ionization involving hot carriers or upon bi-polar charge recombination (a definition that excludes light from partial discharges, which would sign an advanced stage in the degradation process). After a brief review of the EL phenomenology under DC, we introduce a numerical model of charge transport postulating a recombination controlled electroluminescence. The model output is critically evaluated with special emphasize on the comparison between simulated and experimental light emission. Finally, we comment some open questions and perspectives.

Methods and analysis of a simple wireless sensor concept for detecting and locating faults as well as for load monitoring are presented. The concept is based on distributed wireless sensors that are attached to the incoming and outgoing power lines of secondary substations. A sensor measures only phase current characteristics of the wire it is attached to, is not synchronized to other sensors and does not need configuration of triggering levels. The main novelty of the concept is in detecting and locating faults by combining power distribution network characteristics on system level with low power sampling methods for individual sensors. This concept enables the sensor design to be simple, energy efficient and thus applicable in new installations and for retrofit purposes in both overhead and underground electrical distribution systems.

In, this paper, we consider the relation between on-line monitoring and diagnostics on the one hand and high-voltage (HV) withstand and partial discharge (PO) on-site testing on the other. HV testing supplies the basic data (fingerprints) for diagnostics. In case of warnings by on-line diagnostic systems, off-line withstand and PO testing delivers the best possible information about defects and enables the classification of the risk. Because alternating voltage (AC) is the most important test voltage, the AC generation on site is considered. Frequency tuned resonant (ACRF) test systems are best adapted to on-site conditions. They can be simply combined with PO measuring equipment. The available ACRF test systems and their application to electric power equipment -from cable systems to power transformers - is described.

Continuous on-line temperature monitoring allows corrective measures to be taken to prevent upcoming failure. Continuous temperature monitoring and event recording provides information on the energized equipment's response to normal and emergency conditions. On-line temperature monitoring helps to coordinate equipment specifications and ratings, determine the real limits of the monitored equipment and optimize facility operations. Using wireless technique eliminates any need for special cables and wires with lower installation costs if compared to other types of online condition monitoring equipment. In addition, wireless temperature monitoring works well under difficult conditions in strategically important locations. Wireless technology for on-line condition monitoring of energized equipment is applicable both as standalone system and with an interface with power quality monitoring system.

The paper considers the relation between on-line monitoring and diagnostics on the one hand and high-voltage (HV) withstand and partial discharge (PD) on-site testing on the other. HV testing supplies the basic data (fingerprints) for diagnostics. In case of warnings by on-line diagnostic systems, off-line withstand and PD testing delivers the best possible information about defects and enables the classification of the risk. Because alternating voltage (AC) is the most important test voltage, the AC generation on site is considered. Frequency tuned resonant (ACRF) test systems are best adapted to on-site conditions. They can be simply combined with PD measuring equipment. The available ACRF test systems and their application to electric power equipment -from cable systems to power transformers - is described.

A field-oriented UHF system for on-line PD monitoring of transformers. is designed, which has been installed inside the oil tank of a transformer by two ways: on-line installing mode through the oil-valve and pre-installing mode through the man hole/hand hole cover. This system has successfully captured long intermittent discharge signals that hadn't been detected through conventional techniques, and solved the problem successfully. The results demonstrate that UHF technique has great advantages for on-line PD monitoring of transformers. By adopting the peak detection technique, it becomes easy and effective for the transplantation of the phase-resolved pattern recognition technique from conventional method to UHF method, and then to realize continuous on-line monitoring, source characterization and trending analysis.

In this paper, viologen derivative is used as charge transfer material to develop sensors for detecting the organic pollutants which are the main reason of harbor pollution. We fabricated self-assembled monolayers of viologen derivative on gold electrode of QCM and investigated an electrochemical behavior property. We also determined electrochemical sensing property about environmental pollution materials such as bezene, phosphate and surfactant through quantitative and qualitative analysis of charge transfer using intrinsic property of viologen derivative by temperature and concentration change. From the achieved results, we can apply and develope the detecting sensors for harbor pollutants.

Blue emitting materials have been explored by various researchers. However, blue-emitting materials with high luminous efficiency, good color purity, and thermal stability are still much desired. In this study, we synthesized a new blue luminescent material, $SnDP(HPB)_2$ which is low molecular compound and thermal stability. The PL spectrum of $SnDP(HPB)_2$ was observed blue at the wavelength of 447nm. The ionization potential(IP) and the electron affinity(EA) of $SnDP(HPB)_2$ was measured to be 6.7 eV and 3.0 eV, respectively. The fundamental structure of the OLED was ITO/NPB/$SnDP(HPB)_2/Alq_3$/LiF/Al. As a Result, we obtained to enhance the performance of blue OLED.

We investigate characteristics of J-aggregation as take advantage of LB technic. In order to confirm the applications possible for the molecular electronic device, the morphological properties of merocyanine dye were investigated by AFM. $\pi$-A curves investigated the surface pressure of the LB film from a liquid to a solid state ranged between 90 and 100 mN/m. We observed aggregation and it's characteristics by using visible reflection spectroscopy. This paper focuses on results obtained in mercocyanide dye. When LB films of merocyanine dye are mixed with arachidic acid, J-aggregate formation is exhibited. J-aggregate formation has been serving as typical systems in revealing the physical and structural aspects of nano-sized molecular aggregates constructed as muiltilayers.