Thick films of Carbon fiber were prepared by a heating element of plan shape made in Darin co.. We have investigated surface morphology of the specimen depending on second heat-treatment temperatures. X-ray diffraction patterns of Carbon fiber thick films show that the specimen heat treated below $600^{\circ}C$ was an amorphous phase and the one heat treated above $1100^{\circ}C$ forms a poly-crystallization. Scanning electron microscope(SEM) image of Carbon fiber thick films of the specimen heat treated in between 900 and $1100^{\circ}C$ shows a grain growth. At $1100^{\circ}C$, the specimen stops grain-growing and becomes a poly-crystallization.

The $SrBi_2Ta_2O_9$ thin films are deposited on Pt-coated electrode(Pt/$TiO_2/SiO_2$/Si) using RF magnetron sputtering method. The ferroelectric properties of SBT capacitors with annealing temperatures were studied. Through the x-ray diffraction analysis and the scanning electron microscopy (SEM), it could be observed that crystallization of the SBT thin film started around $650^{\circ}C$ and complete crystallization was accomplished around $750^{\circ}C$ and grains grew from a small spheric form to rod-like. For the leakage current density of the SBT capacitor depending upon various annealing atmospheres, capacitor annealed in the oxygen atmosphere showed the most excellent characteristic, and they were respectively about $2.13\times10^{-9}[A/cm^2]$ at 5V and 340.

The purpose of this study was to investigate heat resistance for union type SMD inductor core. The samples was produced with process 5 step. In this study, it analysis heat resistance of SMD(Surface Mounted Device) inductor core and it get electric field only exist inside of SMD core. Therefore electric fields do not affect any device and equipments. These results are very important to design data acquisition system(several test equipments such as temperature, impedance, and current test), because data acquisition system can place under the SMD Inductor core. So, it can be decrease their test error due to electric field.

In the procedure of the estimation, the short time breakdown characteristics for the epoxy composite specimens, which were made with the variation of hardener and/or filler, were tested firstly. Then the long time voltage-to-time test was implemented. Finally, the long time breakdown voltage of each specimen was estimated with the parameters obtained from the statistical treatment with Weibull distribution. Base on the results, it has been found that the optimal weight ratio of epoxy resin/hardener/filler that has the excellent long time breakdown characteristic was 100/100/65. It was due to the silane treatment which relieves the electric field at the interface between filler and epoxy.

We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage. And then, each experiment was performed to irradiation group and non-irradiation group for bone marrow cells. MIT assay method was chosen to verify the cell increase of two groups and the effect of irradiation on cell proliferation was examined by measuring 590nm transmittance of ELISA reader. As a result, the cell increase of bone marrow cells was verified in irradiation group as compared to non-irradiation group.

Organic field-effect transistors (OFETs) are of interest for use in widely area electronic applications. We fabricated a copper phthalocyanine (CuPc) based field-effect transistor with different metal electrode. The CuPc FET device was made a top-contact type and the substrate temperature was room temperature. The source and drain electrodes were used an Au and Al materials. The CuPc thickness was 40nm, and the channel length was $50{\mu}m$, channel width was 3mm. We observed a typical current-voltage (I-V) characteristics in CuPc FET with different electrode materials.

Built-in voltage in organic light-emitting diodes was studied using modulated photocurrent technique ambient conditions. From the bias voltage-dependent photocurrent, built-in voltage of the device is determined. The applied bias voltage when the magnitude of modulated photocurrent is zero corresponds to a built-in voltage. Built-in voltage in the device is generated due to a difference of work function of the anode and cathode. A device was made with a structure of anode/$Alq_3$/cathode to study a built-in voltage. ITO was used as an anode, and Al and LiAl were used as a cathode. A layer thickness of Al and LiAl were 100nm. Obtained built-in voltage is about 1.0V in the Al layer was used as a cathode. The obatined built-in voltage is about 1.6V in the LiAl layer was used as a cathode. The result of built-in voltage is dependent of cathode. We can see that the built-in voltage increase up to 0.4V when the LiAl layer was used as the cathode. These results correspond to the work function of LiAl which is lower than that of Al. As a result, the barrier height for an electron injection from the cathode to the organic layer could be lowered when the LiAl was used as a cathode.

본 연구에서는 우리나라와 같은 낮은 풍속에서 사용 가능한 블레이드의 형태와 블레이드의 피치각이 풍력터빈의 효율에 미치는 영향을 확인하고자 블레이드를 2종류의 형태로 제작하여 블레이드의 피치각에 따른 출력특성을 측정 하였다. 풍력터빈의 효율은 블레이드의 형태와 피치각에 대해 출력이 크게 좌우되었으며, 낮은 풍속 상태에서는 공기의 힘을 받는 면적이 클수록 출력특성이 좋게 나타났다.

Photovoltaic effects in organic solar cell were studied in a cell configuration of ITO/PEDOT:PSS/CuPd(20nm)/$C_{60}$(40nm)/BCP/Al(150nm) at room temperature. Here, the BCP layer works as an exciton blocking layer. The exciton blocking layer must transport electrons from the acceptor layer to the metal cathode with minimal increase in the total cell series resistance and should absorb damage during cathode deposition. Therefore, a proper thickness of the exciton blocking layer is required for an optimized photovoltaic cell. Several thicknesses of BCP were made between $C_{60}$ and Al. And we obtained characteristic parameters such as short-circuit current, open-circuit voltage, and power conversion efficiency of the device under the illumination of AM 1.5.

본 연구에서는 전면 유기 발광소자(TE-OLED)를 제작하여 전기 광학적 특성을 연구하였다. 전면 발광 OLED의 투명 전극으로 사용된 Al과 Ag의 박막 두께에 따른 투과율과 면저항값은 다음과 같이 나타났다. 파장 520nm의 기준으로 Al 금속 박막의 두께가 10nm 이하여야 50% 투과율을 보였고, 반면 Ag는 25nm 이하로 나타났다. 면저항값은 박막두께 20nm 기준으로 Al은 약 $40\Omega/\square$, Ag는 $10\Omega/\square$이하로 나타났다. 전면발광 방식의 시야각에 따른 빛의 세기는 cos $60^{\circ}$ 일 때 0.1로, TE-OLED는 시야각이 증가하였을 때 현저히 감소되는 것을 볼 수 있다. TE-OLED의 시야각의 증가에 따른 EL-peak 또한 약 520nm의 파장대에서 약 500nm으로 변화하였다. 전면 발광 방식의 반폭치(FWHM)는 배면 발광 방식 보다 약 32nm정도 좁게 나타났다.