In this paper, a hybrid dual band LNA(Low Noise Amplifier) with a tunable matching circuit using varactor is designed for 433MHz and 912MHz RFID reader. The operating frequency is controlled by the bias voltage applied to the varactor. The measured results demonstrate that S21 parameter is 16.01dB and 10.72dB at 433MHz and 912MHz, respectively with a power consumption of 19.36mW. The S11 are -11.88dB and -3.31dB, the S22 are -11.18dB and -15.02dB at the same frequencies. The measured NF (Noise Figure) is 15.96dB and 7.21dB at 433MHz and 912MHz, respectively. The NF had poorer performance than the simulation results. The reason for this discrepancy was thought that the input matching is not performed exactly and a varactor in the input matching circuit degrades the NF characteristics.

최근 이동통신을 이용해 다양한 서비스를 제공하기 위하여 멀티 밴드, 멀티 채널의 송수신기를 단일칩화 하기 위한 연구가 활발히 진행되고 있다. CMOS 집적 회로 기술은 가격 경쟁력이 높고 집적도가 높아 멀티 밴드, 멀티 채널 송수신기를 집적화하기에 적합하다. 그러나 0.18 ${\mu}m$ 이하의 채널 길이를 갖는 CMOS 집적 회로는 1.8 V 이하의 낮은 공급 전압을 제공함으로 높은 이득을 갖는 mixer의 구현이 어렵고, mixer에서 발생되는 2, 3차 상호 변조에 의한 왜곡으로 선형성이 문제가 된다. 이런 문제점을 해결하기 위해서 기능성 능동부하를 적용하여 선형성을 향상한 Direct Conversion Down Mixer를 설계 분석 하였다.

CMOS technology 기반의 고주파 직접회로에서는 충분한 이득과 안정성을 얻기 위하여 inductor, capacitor와 같은 수동 소자를 적절히 사용하여 설계하여야 한다. 이와 같은 수동 소자는 CMOS 집적회로에서 넓은 면적을 차지하는 단점이 있다. 고주파 증폭기의 부하를 능동 소자로 대체하게 되면 작은 크기로 회로의 제작이 가능하게 되나, 능동 소자는 수동 소자에 비하여 선형 특성이 좋지 않기 때문에 실제로 고주파 증폭기 설계에 사용하지 않는다. 본 논문에서는 이와 같은 능동 소자의 비선형성을 억제하면서, 동시에 회로의 크기를 줄일 수 있는 기능성 능동 부하를 적용한 고주파 증폭기를 설계하였다. 기능성 능동 부하는 2개의 MOSFET은 대칭으로 연결된 구조를 가지며, 하나의 MOSFET은 일반적인 load로 동작하며, 다른 MOSFET은 gate에 가변 전압을 인가함으로써, 증폭기의 전달함수를 변화시킬 수 있다. 이와 같은 특성을 이용하여 고주파 증폭기의 선형성을 보상할 수가 있다.

RoF 링크 시스템을 적용한 무선 근거리 통신망(IEEE 802.11b/g)의 중심 주파수 대역인 2.4 GHz에서 저가의 Febry-Perot 레이저 다이오드를 이용한 피드포워드 광송신기를 제작 및 측정 하였다. 제작된 피드포워드 광송신기의 측정 결과는 2.4 GHz에서 주신호의 간격이 10 MHz이고 크기가 -4 dBm인 입력 신호에서 피드포워드 보상기법을 적용하기 전보다 3차 상호 변조 왜곡 신호가 22.9 dB 개선되었다. 제작된 피드포워드 광송신기의 전자소자의 사양을 바탕으로 송신기 집적을 위한 RFIC회로(감쇄기, 증폭기)를 0.18 ${\mu}m$ 공정을 이용하여 설계하였다.

디지털용 Uncooled DFB 레이저 다이오드를 이용하여 광대역 아날로그 피드포워드 광송신기를 제작하였다. 광송신기의 상호변조왜곡 성분 및 잡음성분을 제거하기 위해 광 피드포워드 보상기법을 사용하였으며, 다중서비스를 위해 $2.05{\sim}2.60$ GHz(550 MHz)에서 상호 변조왜곡 성분이 10 dB 이상 억제되었고, 상대강도잡음은 1.5 dB 이상 억제되었다. 2.3 GHz 에서 3 차 상호변조왜곡성분이 21.3 dB, SFDR 이 7.11 dB 향상된 결과를 얻었다. 또한 단일 모드 광섬유 전송 실험을 통해 전송길이에 따른 3 차 상호변호 왜곡성분의 크기 변화를 확인하였다.

In the fibre to the home (FTTH) era, it is expected that broadband network provisioning will require thousands of optical fibres to be accommodated in a central office for optical access networks. An optical fibre line testing system could be used to reduce maintenance costs and improve service availability depending on the PON's element manager capabilities and the maintenance procedures adopted by the network supplier. When monitoring optical fibres transmitting communication lights, a wavelength of 1625 nm is used for maintenance testing. The splitter installed optical filters allow the communication light to pass but that cut off the test light in the front of optical line terminals (OLTs) and optical network terminals (ONTs). In the economic point of view, We design new planer lightwave circuit splitter embedded filtter and study it optical property.

This paper deals with an equivalent circuit model for RF passive components. Rational functions are obtained from the frequency responses of EM simulation by using Foster canonical partial fraction expressions. The Vector Fitting(VF) and the Adaptive Frequency Sampling(AFS) scheme are also implemented to obtain the rational functions. A passivity enforcement algorithm is applied to ensure the stability of the equivalent circuit model. In order to verify the schemes, S parameters of the equivalent circuit model is compared to those of EM simulation in case of the microstrip line structure with 3 slots in ground.

This work presents the simplified mechanism that the microstrip line generates the radiated emission which is one of the measures on the EMI levels. The electric currents on the metallization of the structure are input to the radiation integrals with the Green's functions being derived to consider the stratification of the microstrip. The simulated results suggest the method of the conceptualization on the RE characteristics of the signal trace in the PCB structure.

효율적인 OFDM(Orthogonal frequency division multiplexing)의 동작을 위해 데이터의 시작 위치를 검출하는 프레임 동기 과정은 필수적인 요소이다. 본 논문에서는 OFDM 을 기반으로 한 이동 멀티미디어 통신 시스템에 적용가능한 새로운 프레임 동기 방법을 M-sequence 를 이용하여 설명하고 분석한다. 두 개의 반복되는 M-sequence 는 시간 영역에서 OFDM 의 프레임에 직접 더해지고, 수신단에서 M-sequence 의 자기상관 특성을 수행함으로 효과적인 프레임 동기를 얻을 수 있다. 이와 함께 주파수 옵셋 추정 알고리즘이 이루어 진다. 제안된 알고리즘은 비교적 단순하며 다중경로채널에서도 훌륭한 특성을 보여준다. 마지막으로 이 기술은 4G 이동 멀티미디어 통신 시스템에 적용할 수 있다.

Multi-input multi-output (MIMO) system can increase data rate, capacity and bit error rate (BER) performance compare to traditional single antenna system. However MIMO technique is pointed out the problem that has high complexity to design receiver. So a recent trend of research on the MIMO system pays more attention to simplified implementation of receiver structure. In this paper, we propose differential space time block code (STBC) for MIMO system with cyclic delay diversity (CDD). This structure can provide a very close performance to that of the conventional diversity scheme with maximum likelihood (ML) detection without channel estimation block while the receiver structure is highly simplified. Bit error rate (BER) performance of the proposed system is simulated for an AWGN channel by theoretical and simulated approaches. The results of this paper can be applicable to the 4G mobile multimedia communication systems.

Multiple Antenna Technologies such as Multiple-Input Multiple-Output (MIMO) and Beamforming provide the increase of channel capacity and the reliability of wireless link. To obtain these advantages, WiBro, Mobile WiMAX and $4^{th}$ Generation System are employing multiple antenna technologies. There exist, however, many technical issues in considering the application of the technologies or the providing of services using them. In this paper, various technical topics are discussed and simple solutions are proposed. Beamforming has several technical issues which include coverage imbalance, difficulties in providing Multicast-Broadcast Service (MBS). In Addition, network planning is a critical point from a cell extension and initial network entry point of view. In case of MIMO, network deployment is discussed in that cellular data network such as WiBro has many repeaters. MIMO mode selection for maximizing the cell capacity is also covered.

현재 국내에서 ITS(Intelligent Transport Systems) 통신방식으로 이 용되고 있는 DSRC 방식은 TTA(한국정보통신기술협회)의 기술표준으로서 대전시,전주시에 적용되어 BIS(Bus Information Service)에 이용되고 있고,최근 고속도로 ETCS(Electronic Toll Collection System)가 DSRC방식으로 전국고속도로 Tollgate 에서 2007년 연말에 개통될 예정이다. DSRC 방식은 2000년에 TTA(한국정보통신기술협회)에서 기술표준이 제정되어 현재 1Mbps 의 Data 용량을 가진다. DSRC 방식의 물리링크 변조방식은 ASK(Amplitude Shift Keying)로 ITS 확장 서비스 적용을 위해 변조방식을 QPSK(Quadrature Phase Shift Keying )로 개선하게 되면 이론적으로 4배의 Data Rate 향상이 이루어진다. 물리적인 RF 변조방식을 ASK에서 QPSK로 바꿔 간단히 Data Rate을 개선하게 되면 회로구현의 경제성이 향상되어 DSRC 응용 서비스가 활성화 될 것이다.

An adaptive subcarrier allocation scheme based on comparative superiority of opportunity cost between groups is proposed for the enhancement of system capacity and its simple implementation at the base station of a multiuser OFDM system. The proposed algorithm is similar to the blockwise or the decentralized subcarrier allocation algorithm proposed by Xiaowen et al and Alen et al, respectively. In the proposed algorithm, however, all subcarriers are grouped according to the coherence bandwidth and the comparative superiority concept, which swaps the groups between users if the system capacity is increased, is adopted for the enhancement of system capacity. In addition, the proposed algorithm provides a simple solution for the conflict problem among users by reallocating only the conflicted groups and unassigned groups instead of reallocating entire groups. Simulation results demonstrate that the proposed algorithm increases the system capacity effectively over a static, an adaptive blockwise, and a decentralized subcarrier allocation algorithms.

본 논문은 지연 다이버시티를 이용한 초광대역무선통신시스템의 PN 부호 포착 성능을 분석하였다. 무선채널은 주파수 선택적인 로그노말 페이딩 채널로 모델링하였다. 포착 성능은 PN 부호의 불확실한 부분에서 여러 개의 동기 상태가 존재한다는 가정하에서 검파 확률과 평균 포착 시간의 관점에서 분석되었다. 시뮬레이션 결과로부터 지연 다이버시티를 이용한 포착 시스템이 낮은 수신기의 단가와 복잡도에도 불구하고 다이버시티 이득을 획득할 수 있다는 것이 증명되었다. 본 논문의 결과는 CDMA에 기초한 초광대역무선통신시스템의 동기단을 디자인하는데 적용될 수 있다.

Commercial WiBro and 3G HSDPA services are launched last year in order to provide high speed wireless Internet access and multimedia service. Currently mobile communication service providers concentrate on the deployment of indoor mobile network since indoor traffic is remarkably increased. For fine indoor wireless communication, an installation of access point system via Public IP network which is called Femtocell is required. The development of indoor Femtocell system must be considered in the viewpoint of low hardware complexity, cost reduction, interlocking with WiBro/HSDPA network without change of network component and easy element management. In this paper, we review the implementation issue and technology of dual mode AP which provides WiBro and HSDPA signal to the user simultaneously. Especially, we describe on the HSDPA Femtocell standardization status and possible 3 types of HSDPA communication module development design. Furthermore we analyze the merits and demerits of each HSDPA Femtocell design type and propose a system which enables handover between indoor HSDPA Femtocell and outdoor commercial HSDPA mobile network.

In this paper, we analyze the performance of the network management system with intelligent mobile agent system. The proposed system dynamically selects appropriate its destinations. Thus, the system has an advantage of flexible network management in mobile network environments as well as dynamic change of traffic. Comparing its delay and throughput performance with the conventional SNMP based network management system, we find that the proposed mobile agent system performs better efficiency than the conventional one.

국내의 홈네트워크 서비스는 홈오토메이션 제공 중심에서 엔터테인먼트 요소가 강화된 멀티미디어 기반의 네트워크 서비스로 변모하고 있다. 홈네트워크를 구성하는 요소 중 PC와 TV는 댁내에 멀티미디어 기반의 네트워크 서비스를 구축하는데 있어 가장 중요한 역할을 수행할 것으로 예상된다. 그에 따라 PC와 TV 간 네트워크를 구축하는 것이 중요한 이슈로 떠오르고 있다. 그러나 PC와 TV 간 네트워크 구축을 위해서는 댁내 노출 배선 등의 문제로 인하여 무선 기술을 사용하는 것이 유용하지만, 현재 기존 무선 전송 기술(IEEE 802.11 a/b/g, Bluetooth 등)들은 HD 등의 대용량 컨텐츠 전송 및 QoS 를 제공하기가 어렵다. 따라서 본 논문에서는 PC와 TV 간 무선으로 네트워크 구축시 고려사항 및 무선전송기술개발 요소를 살펴본다. 특히 무선전송기술로는 고속 데이터 전송이 가능한 UWB(Ultra Widebnad)와 IEEE 802.11n 기술을 중심으로 고려한다. 또한 UWB와 IEEE 802.11n을 이용하여 네트워크가 구축되었을 때 제공 가능한 서비스 시나리오에 대해서도 소개한다.

2007년도 상반기부터 단독주택지역 가입자를 대상으로 FTTH 구축이 꾸준히 증가하고 있으며, 초고속 인터넷 서비스를 비롯한 고화질의 IP-TV등의 서비스제공이 상용화 단계에 있다. 단독주택지역의 FTTH의 구축은 향후에도 지속적으로 추진해 나갈 예정으로 있으며, 신축아파트 또한 정보통신건물 인증 정책 추진으로 초기의 건물 신축 당시부터 UTP케이블 및 광케이블의 구축이 보편화되는 추세이다. 반면에 건축된지 오래 경과된 기축아파트의 경우에는 여러 가지 건물 구조형태의 문제점과 열악한 구내통신시설 환경으로 FTTH를 구축하는데 많은 어려움이 있으며, 구축방법의 부재로 인하여 활발히 추진되지 못하고 있는 실정이다. 본 논문에서는 이러한 기축아파트를 대상으로 FTTH 구축을 효율적으로 하기 위한 방법에 대해 언급하였고, 아파트 구내통신설비를 세부 구간별로 분리하여 최적의 FTTH 구축을 할수 있는 방법에 대해서 논하였다.

This paper describes various FTTH topology such as FTTH-R, Hybrid-FTTH etc. Especially, we focus on GW-PON based Hybrid-FTTH topology. Furthermore, the optical link technology and the features of the developed GW-PON system were explained in detail.

Multimedia service based on interactivity, personalization, multiple channels and community distinguishes IPTV from incumbent TV. But data encoding/decoding time and image frame processing should be considered in digital TV versus analog device. Especially channel zapping time is one of the most important parameters for the service quality of IPTV. This paper proposes the mechanism for decreasing the channel zapping time with multiple decoder and image frame processing. We also implemented the multi-group video community service system using IP multicasting function supporting interactive learning service.

현재 통신 시장은 보다 편리하고 다양한 서비스를 찾는 소비자의 욕구와 맞물려 TPS(Triple Play Service) 방향으로 급속히 나아가고 있다. 인터넷 전화의 보급은 이미 보편적 서비스가 된 초고속인터넷 서비스와 연계하여 빠르게 확산되고 있으며, 2007년 들어 방송서비스까지 결합한 TPS에 대한 통신사업자간 경쟁이 본격화되고 있는 추세이다. 트리플 플레이 서비스(Triple Play Service;이하 TPS)는 초고속 인터넷과 인터넷 전화와 방송 서비스를 하나의 회선으로 제공하는 종합 인터넷 서비스로, 광대역 통합망(BcN; Broadband Convergence Network)의 핵심 서비스이다. 액세스 스위치(Access Switch) 단은 TPS로 인해 더욱 많은 역할을 담당할 것으로 전망되는데, 디지털 방송을 인터넷 프로토콜을 통해 전송하기 위한 멀티캐스트 기능과 혼재된 이종간의 디지털 신호를 각 서비스의 품질에 맞게 보장해 주는 QoS(Quality of Service) 기능이 무엇보다 중요하게 고려 되어야 한다. 본 논문에서는 TPS의 핵심일 수 있는 방송 서비스를 위해 액세스 스위치 단에서 제공해야 할 멀티캐스트와 QoS 기능 구현 방안에 대해 제시한다

For several ten years, the Internet and IT services have been greatly developed in PC area and with this, new BM and services with terminals like Post-PC and Non-PC types will come into the spotlight in few years. In various fields of service, terminals exclusive to individual service come into the market already, the hardware and the contents used in the terminals are circulating. The communication service providers are very enthusiastic about developing and providing various services in order to overcome the growth limit of existing network connection service. And they think that providing the Non-PC type Information Appliance services will make added values and be sources of making profits in next generation. Hereupon we are going to observe the Non-PC type Information Appliance services, the structure of the service platform that make that services possible, and their prospect.

FTTH상용화, IEEE802.11n 무선랜 기술의 상용화 등과 같은 초고속 전송기술의 발전에 따라 홈네트워킹 환경 또한 급격하게 변화하고 있다. 100Mbps를 초과하는 많은 홈네트워킹 기술들의 개발로 인해 홈게이트웨이에 보다 넓은 대역의 LAN 인터페이스를 요구하게 되었고, xDSL이나 케이블모뎀 기반의 가입자망과의 대역폭 차이는 고성능의 QoS 기능을 요구하게 되었다. 이러한 통신환경을 토대로 홈게이트웨이의 기능에 대한 요구사항을 분석하고 홈게이트웨이용 스위칭 칩의 개발규격을 도출하였다. 그리고 새로운 네트워크 기반의 비즈니스 모델을 개발하고자 하는 통신사업자의 요구사항과 QoS나 IPv6등의 다양한 네트워크 요구사항을 등을 유연하게 수용할 수 있으며, 칩의 기능과 성능을 수정하 또는 추가할 수 있는 네트워크 프로세서 기반의 기가빗 스위치 칩을 개발하였다. 개발 칩은 패킷 프로세서로 Layer 4까지 의 패킷헤드를 처리하고, 2기가빗이더넷 + 6패스트이더넷 포트를 갖도록 설계하였으며, FPGA를 이용하여 스위칭 칩의 기본적인 전송기능과 성능, Flow별 패킷 분류 및 패킷 필터링, 스케쥴링 기능 등의 시험을 통하여 설계한 칩의 기능과 성능을 확인하였다.

본 논문에서는 인터넷전화 품질평가를 위한 국내 동향에 대하여 기술하고, BcN영상전화 서비스에 대한 SLA 품질지표 및 품질기준을 국내외 동향 및 기준표준화에 근거하여 마련하고 이를 검증하기 위한 품질측정 방법을 제시하고자 한다. 이를 통해서 영상전화 서비스의 SLA 품질기준이 조기에 마련되어 국내 통신사업자들의 이용약관에 반영되기를 기대한다. 따라서 본 논문의 목차는 서론, SLA 개요, 영상전화 서비스의 품질지표 및 기준, 품질지표별 측정방법 및 시험측정 결과에 대하여 기술하였다.

This article describes a definition of next generation access network, and introduces the researches about a candidate optical links for the next generation access network, and a trend of standardization of Next Generation Access (NGA). Expansion in reaches of access network enables to the evolutions to the metro-access union system. Also, this paper reviews the access network in Korea, and suggests the requirements for the system in NGA.

This article describes a function and structure of access network equipment under BcN environment. Access network until now have constructed separately to offer voice, data service. However, simplifies network structure, function that can do traffic concentration, subscriber certification, individual charging, QoS according to service and routing is required in BcN. In this paper, compare method offering by separate system with existing access network and method that offer integrating function inside system for structure of suitable access network to BcN and search structure of access network equipment for desirable access network of hereafter. Composition of this paper is as following. In Chapter 2, establishment history and structure of access network until present. In Chaprte 3, define suitable requirement and functions to BcN. And compare structure for access net work that is new with present. Last Chapter 4, suggests direction of structure of BcN access network and concludes conclusion.

본 논문에서 제안하고자 하는 IPTV 채널캐슁 서비스는 IPTV 서비스의 품질요소인 QoE(Quality of Experience)의 개선을 목적으로 하고 있다. IPTV 채널캐슁 방법은 IPTV 서비스가 실시간 방송 및 VOD(Video On Demand)등 다양한 패턴의 서비스를 선택하는 사용자의 채널요구 패턴을 반영한 인접채널(adjacent-channel)을 멀티캐스트하면, 사용자의 채널전환요구시 제어메시지 전송 및 스위칭에 소요되는 대기시간을 줄여 사용자의 채널전환지연시간을 개선할 수 있다. 이를 위하여 본 논문에서는 LRFU(Least Recently Frequently Used) 알고리즘에 기반한 MCA(Multicast Channel Agent)을 제안하며, MCA을 구성모듈에 대한 설명을 기술한다.

논문은 LG 데이콤의 TPS 서비스에서 사용되는 여러 단말의 초기 설치의 편의성을 최대한 보장하기 위한 자동 프로비저닝 시스템에 대한 연구이다. 이를 위해서 요구되는 단말기의 식별자와 암호화를 처리하기 위한 자동 프로비저닝 시스템의 수행 절차를 제안한다. 기본 구성은 홈게이트웨이를 이용한 홈네트워크를 구성하고 있다. 이를 기반으로 하여 IPTV 셋탑, WiFI 폰, PC 를 동시에 사용하기 위해서는 자동 프로비저닝 시스템에서 여러 단말기로 네트워크 접속에 필요한 정보(접속할 시스템의 주소(IP), 포트 및 환경 파일)를 전송하거나, 단말기가 직접 다운받을 수 있도록 한다. 이를 제공하는 시스템을 TPS 자동 프로비저닝 시스템이라 명하며, 이는 가입자의 개입없이 홈네트워크 환경과 멀티미어어 서비스 환경을 자동으로 설치함으로써 사용자의 편이성을 극대화하게 된다. 본 논문은 TPS 서비스와 디지털 홈 서비스의 근간이 되는 프로비저닝 플랫폼의 기술적 가능성을 검증함으로써 향후 관련 단말기 개발 및 개방형 서비스를 제공하기 위한 기초자료로 활용되고자 한다.

The frequency accuracy and phase alignment is necessary for ensuring the quality of service (QoS) for applications such as voice, real-time video, wireless hand-off, and data over a converged access medium at the telecom network. As telecom networks evolve from circuit to packet switching, proper synchronization algorithm should be meditated for IP networks to achieve performance quality comparable to that of legacy circuit-switched networks. The Time of Packet (ToP) specified in IEEE 1588 is able to synchronize distributed clocks with an accuracy of less than one microsecond in packet networks. But, The ToP can be affected by impairments of a network such as packet delay variation. This paper proposes the efficient method to minimize the expectable delay variation when ToP synchronizes the distributed clocks. The simulation results are presented to demonstrate the improved performance case when the efficient ToP transmit algorithm is applied.

Digital Rights Management (DRM) technology has been widely used for protecting the digital contents over the recent years. But the digital contents protected by DRM are vulnerable to various video memory capture programs when DRM packaged contents are decrypted on the consumers' multimedia devices. To make up for this kind of DRM security holes the Forensic Marking (FM) technology is being deployed into the content protection area. Most leading DRM companies as well as big electronics companies like Thomson and Philips already have commercial FM solutions. Forensic Marking technology uses the digital watermarking to insert the user information such as user id, content playing time and etc. into the decrypted and decoded content at the playback time on the consumer devices. When the content containing watermarked user information (Forensic Mark) is illegally captured and distributed over the Internet, the FM detection system takes out the inserted FM from the illegal contents and informs contents service providers of the illegal hacker's information. In this paper the requirements and test conditions are discussed for the commercial Forensic Marking systems.

This paper presents an advanced RFID reader system implementing multi-protocols and multi-standards at 900MHz. In accordance with the strict regulations specified by ISO 18000-6 B-Type and EPC Global Gen 2, we have designed corresponding systemic factors which meet the domestic radio frequency utilizing bands of 910-914MHz. In addition, we develop numerous crucial factors of system compatibility options including SSB (Single-Side Band) and DSB (Double-Side Band) specifications, also OOK (On-Off Keying), ASK (Amplitude Shift Keying) and PR-ASK (Phase Reversed-Amplitude Shift Keying) modulation formula. Remarkable technical features of system in this paper can be the direct conversion routines using I/Q Modulation/Demodulation respectively, and Full-Duplex formulation operating at identical frequency bands.

This paper describes the project for constructing a traceability system for producing using RFID antenna in 900MHz frequency band and the consideration. In this project we reviewed analysis of properties classified by production process and RFID system through each frequency band, and designed a single unit RFID reader including antenna. The developed antenna is optimized to a field condition and this paper will show the test results. Also, we designed a single unit RFID reader by adding a reader to a designed antenna and explained the rule of tag memory allocation. Lastly, after running the system we could calculate visible and invisible effects of operation results and check up a wide possibility of application for RFID.

In this paper, we solved the underestimation problem of PSNR, which is caused by repeated frames, by easily synchronizing original and decoded frames using the proposed marks. Also we propose full-reference system which can be applied for measuring the quality of various kinds of video communication systems, e.g. wireless handsets, mobile phones and applications for PC. In addition, we propose a new video quality assessment metric using video communication parameters, i.e. frame rate and delay. According to the experiments, the proposed metric is not only appropriate for real-time video communication systems but also shows better correlation with the subjective video quality assessment than PSNR. The proposed measuring system and metric can be effectively used for measuring and standardizing the video quality of future communications.

최근 IPv6 기반 WiBro 망에서 다수의 사용자가 동종망간 혹은 이기종망간 인터넷 연결을 유지하면서 그룹으로 이동하는 상황에서의 핸드오버 처리 폭증 및 핸드오버 지연 시간 문제를 효율적으로 해결할수 있는 기술 및 시스템이 요구되어 지고 있다. 본 이동 AP는 IPv6 기반 WiBro 망에서 다양한 광대역무선망 접속 및 다양한 하향 단말 접속이 가능한 하드웨어 기반에 네트워크 이동성 기술를 구현하여 IPv6 기반 WiBro 네트워크 실, 내외 환경에서 이동성을 지원하지 않는 다수의 단말들이 네트워크 이동시 각 단말들의 이동성 처리가 수행됨을 확인하였으며 관련 서비스 연속성이 유지됨을 시험을 통해 확인 할 수 있었다.

This paper describes a IPv6 trial service provided by LG DACOM and discusses about the output of trial service. MIC has urged public organizations to introduce IPv6 technology into their network. As one of propelling policies, MIC and NIA launched some IPv6 trial project. LG DACOM, MIC's agent in doing IPv6 trial project, has selected three public organizations in order to deploy IPv6 based VoIP trial service. KMA, KISITI and MND gave out their different service requirements. In achieve this project we developed IPv6 supported voice IP phone, video IP phone, media gateway and IP-PBX. Furthermore, two KMA provincial offices adopted trial IP phone as working phone and replaced legacy PBX with IP-PBX. At the same time, public organizations introduced IPv6 technology into their local networks.

The word of U-City means next generation information city. U-City mixes both high technology information infrastructure and ubiquitous information in city to improve easy life in city, quality of life, personal security in city life, and well-fare service and to make business in new area. To provide information and joy of life to citizen in U-city, we will design U-Booth among IT infrastructure solutions. In this article, we will study designing city-type U-Booth and summarize designing point of U-Booth in terms of the specific place. At last, we want to say about the role of U-Booth in U-city. In this article, we want to study designing point of U-Booth and important parts in terms of the specific place of U-Booth.

So far, almost all IP media services are targeted to the specific devices, for example, IPTV services are mainly for TV, and social community services are mainly for PC etc.. This paper describes newly developed media service platform in which the high quality video services can be provided not only to the TV or PC but also to the PMP(Portable Media Player) and even to the mobile phone. The major technical issues of the service platform are synchronization of contents among the different devices and high quality TV grade video display in PMP device. We confirmed successful operation of multi-device converged services in the developed media platform. We also have a trial service plan in Gwangju city at the end of this year.

In this study, we deployed the cable tunnel inspection and monitoring system by wireless sensor network. It is shown that the wireless sensor network which is composed of sensor, wireless communication module, and gateway can be applied to cable tunnel monitoring system. Sensors considered herein are flame detection sensor, flood detection sensor, intruder detection sensor, and temperature sensor, etc. It is also found that the wireless sensor network can deliver sensing data reliably by wireless sensing technology. The gateway system that can transmit sensed data to server by CDMA is developed. Monitoring system is constructed by web service technology, and it is observed that this system can monitor the present state of tunnel without difficulties. The system provides an alternative to inspect and monitor the tunnel efficiently where the conventional wired system is infeasible.

Up to now, a lot of houses, roads and other urban facilities have been damaged by natural disasters such as flash floods and landslides. It is reported that the size and frequency of disasters are growing greatly due to global warming. In order to mitigate such disaster, flood forecasting and alerting systems have been developed for the Han river, Geum river, Nak-dong river and Young-san river. These systems, however, do not help small municipal departments cope with the threat of flood. In this study, a real-time urban flood forecasting service (U-FFS) is developed for ubiquitous computing city which includes small river basins. A test bed is deployed at Tan-cheon in Gyeonggido to verify U-FFS. Wireless sensors such as rainfall gauge and water lever gauge are installed to develop hydrologic forecasting model and CCTV camera systems are also incorporated to capture high definition images of river basins. U-FFS is based on the ANFIS (Adaptive Neuro-Fuzzy Inference System) that is data-driven model and is characterized by its accuracy and adaptability. It is found that U-FFS can forecast the water level of outlet of river basin and provide real-time data through internet during heavy rain. It is revealed that U-FFS can predict the water level of 30 minutes and 1 hour later very accurately. Unlike other hydrologic forecasting model, this newly developed U-FFS has advantages such as its applicability and feasibility. Furthermore, it is expected that U-FFS presented in this study can be applied to ubiquitous computing city (U-City) and/or other cities which have suffered from flood damage for a long time.

This article describes a development CDMA LBS in order to apply to "Control System of Underground Infrastructure Fire Accident" which one of U-City Projects of Seoul City. Our goal guides taking shelter of the sufferer it will not be able to use a GPS when the fire occurs from subway station. There are Location measurement methods which measures the AOA(Angle of Arrival) of the signal which it sends with the MS(Mobile station) from the BS(Base station), an electronic delivery time (TOA:Time of Arrival) and the relative difference of electronic arrival time from Base stations (TDOA:Time Difference of Arrival). This time the error due to a multiplex course error and near-far problem and NLOS(Non Line of Sight). We are planning to construct the Test Bed which is an error below 1 meter.

Recently, landslides frequently happen at a natural slope during period of intensive rainfall. With rapidly increasing population of steep terrain in Korea, landslides have become one of the most significant natural hazards. Thus, it is necessary to protect people from landslides and to minimize the damage of houses, roads and other facilities. To accomplish this goal, many landslide prediction methods have been developed in the world. In this study, a simple landslide prediction system that enables people to escape the endangered area is developed. The system is focused to debris flows which happen frequently during periods of intensive rainfall at steep slopes in Kangwondo. This system is based on the wireless sensor network that is composed of sensor nodes, gateway, and server system. Sensor nodes that are composed of sensing part and communication part are newly developed to detect sensitive ground movement. Sensing part is designed to measure tilt angle and acceleration accurately, and communication part is deployed with Bluetooth (IEEE 802.15. I) module to transmit the data to the gateway. To verify the feasibility of this landslide prediction system, a series of laboratory tests is performed at a small-scale earth slope supplying rainfall by artificial rainfall dropping device. It is found that sensing nodes installed at slope can detect the ground motion when the slope failure starts. It is expected that the landslide prediction system by wireless senor network can provide early warnings when landslides such as debris flow occurs, and can be applied to ubiquitous computing city (U-City) that is characterized by disaster free.

과거 전화교환사업에 있어서 치국점을 결정하는 가장 중요한 요소는 동선로의 기술적인 성능한계였다. 즉, 전력과 신호를 동시에 공급하는 동선로가 갖는 감쇠제한과 신호제한을 극복할수 있는 위치에 전화국을 건설하여 왔다고 볼 수 있다. 그러나, 광통신 기술의 발전과, VoIP의 출현에 따라 이와 같은 제한요소들은 점차 극복되기에 이르렀고, 과거 통신사업자의 중대한 고민이었던 치국의 중요성은 점점 감소하고 있다. 특히, 신도시, u-City 개발 등을 통하여, 통신 인프라가 구축되어있지 않은 지역(본 고에서는 신규개발지역이라고 함.)의 통신망계획에 있어서, 통신사업자들은 현재의 가용한 기술을 최대한 활용하여 경제적이고도 효율적인 통신망을 구축하고자 시도하여야 할 것이다. 그럼에도, 기존의 통신 사업자가 쉽게 전화 서비스를 광통신 인프라로 전환하기 어려운 것은 VoIP 기술을 차용한 전화 서비스가 시내전화사업으로 인정받기 위해서는 긴급통신의 제공과 함께 정전시 통화기능을 필수적으로 구현하여야 한다는 점에 있다. 이에, 본 고에서는 인터넷 접속과 전화를 동시에 제공할 수 있는 대표적인 솔루션을 정형화하고, 각 모델별 전력공급방안에 관하여 고찰하고자 한다.

일반적으로 홈 게이트웨이는 가정 내 PC와 인터넷 가전 모두에 대해 공유 인터넷 액세스가 가능하도록 통신 서비스와 홈게이트웨이 자체의 보안 및 홈 오토메이션과 같은 서비스를 제공한다. 또한 추가로 미래에 제공되어야 할 여러 서비스를 위해서는 현재 개발되는 홈 게이트웨이는 모듈식 아키텍쳐를 기반으로 해야 할 것이다. 이와 같은 홈 게이트웨이를 구현하기 위해서는 독창적이고 확장 가능한 하드웨어 플랫폼은 물론, 운영체제 및 애플리케이션의 업그레이드와 새로운 서비스의 배치를 가능케 해주는 강건한 파일 시스템을 포함해야 한다. 따라서 본 논문에서는 위와 같은 홈 게이트웨이 기능 및 새로운 서비스 추가 및 관리에 용이한 개방형 표준인 OSGi(Open Service Gateway Initiative)를 기반으로 한 홈게이트웨이를 설계하고, 본 플랫폼을 통한 댁내 가전제어를 위해 센서네트워크와 연동하여 실제 댁내에 부착된 액추에이터 센서노드를 제어할 수 있도록 개발했다. 가전제어를 위한 S/W는 OSGi 상에서 서비스 번들로 개발하였으며 언제 어디에서든 해당 번들을 다운받아 홈 제어가 가능하다.

최근 전자파에 일반인에 대한 관심이 높아지고 있고, 기업들의 환경경영의 일환으로 전자파환경 관리도 하나의 이슈로 대두되고 있다. 초고속인터넷서비스 속도개선을 위해 통신장치를 기존의 전화국사내에서 가입자 주택 가까이 또는 주택 건물의 내부로 이동하여 설치하고 있다. 이런 경우 주변 거주자들은 전자파의 인체 유해성에 대한 우려를 하게 되며, 이로 인해 일부 장치설치 곤란하여 서비스제공에 어려움이 발생하기도 한다. 본 논문은 초고속서비스 제공을 위해 가입자 가까이에 설치된 여러 지역의 옥외 통신설비 주변에서 전자파 측정기술을 서술하고 측정된 결과를 국내 기준과 비교 분석하였다. 측정결과 국내 기준보다 매우 낮은 결과를 보였다.

Development of IT and electronics industries has make our life more convenient, yet at the cost of radio communication noise, malfunctioning of electronic appliance and risks against human health all resulting from EMI. Many states are tightening their EMI (Electro Magnetic Interference) regulations around the world and the EMI regulatory measures are likely to increase in terms of targets and types. Against this backdrop, this paper aims to introduce fundamental and adequate EMI countermeasures encompassing product production cycle from design to production stage.

In this paper, we have analyzed the effects from the change of separation distance between grounding equipment at end of telecommunication line and the inducting facilities in power inducting situation. In the result of measurement, we can see that as the separation distance between grounding equipment ant end of telecommunication line and the inducting facility become longer, the induced noise level and PIF level is decreased. From the another experiment results about the effect of changing the impedance size in both ends of telecommunication line, however, we already knew that as the ground impedance at either end of the telecommunication line become grower, the noise level is increased, and as the ground impedance at either end of the telecommunication line become smaller, the noise level is decreased. Hence we can not define the relationship exactly between separation distance from inducting facility to inducted facility and the induced noise level because when the grounding equipment is moved, its impedance size is changed too. In conclusion, changing the separation distance between grounding equipment at end of telecommunication line and the inducting facilities have not influence on the induced noise level.

일반 전화뿐 아니라 xDSL 초고속서비스를 제공하는 가입자 통신선로는 옥외에 노출되어 있어 매년 우기철 낙뢰 피해가 발생하고, 통신선로에 접속된 단말장치는 낙뢰서지에 의한 부품 소손 및 서비스가 일시 중단되기도 한다. 낙뢰로 인해 가입자 통신선로에서 나타나는 낙뢰유도서지 특성을 파악하는 것은 통신시설 보호 및 서비스 중단을 최소화 할 수 있는 중요한 기초 자료가 된다. 본 논문은 가입자 통신시설에 나타나는 낙뢰유도전압을 측정하여 각종 파라메터 분석 및 가입자선로에 구성에 따른 파라메터 특성 변화를 분석하였다.

This paper first outlines the technology used in Power Line Communications(PLC) systems, and the political support being offered to the technology, from the point of view of its effect on electromagnetic compatibility (EMC). The radio spectrum needs protection from other interferers, and there is a regime in place to provide this interference avoidance/mitigation. Nevertheless, PLC has several features that mean that it is capable of creating such interference. These features are discussed, and some published field trial results are reviewed. Difficulties in achieving compatibility between the requirements for radio protection and the requirements for operation of the PLC system mean that there is no consensus as yet as to how PLC system components can be made compliant with EMC requirements. It is concluded that there is little prospect of an accommodation between the competing demands, so that if PLC is to become widespread it will be at the expense of the radio environment.

In this paper, we have analyzed the change characteristics of induced noise due to the impedance change of the ground in both ends of telecommunication line. As what affects the induced noise, there are power influence or longitudinal transverse voltages and its weighted filtered voltage. In the result of measurement, we can see the noise level change due to the change of the ground impedance, that is, as the ground impedance at either end of the telecommunication line become grower, the noise level is increased, and as the ground impedance at either end of the telecommunication line become smaller, the noise level is decreased. However, we can't define the relation between ground impedance size and PIF in these measurement results, so we will have to carry out the measurement more deeply and more practically with various conditions in environmental viewpoint and/or experimental viewpoint to establish the definition between ground impedance size and PIF.

와전류를 이용한 전위강하법은 시험체에 와전류를 비 접촉식으로 발생 시킬 수 있어 기존의 방식에 비해 결함 검출시 발생하는 오차를 줄일 수 있고 물체의 결함 검출신호의 신뢰성을 향상 시킬 수 있다. 본 논문에서는 와전류를 이용한 전위강하법의 전자기 유한요소해석을 수행하였다. 3차원 유한요소해석과정에서 해석시간을 단축시키기 위해 각 영역별로 MVP, ESP, RMSP, TMSP의 미지수 변수를 부여하여 유한요소해석을 수행하였다. 기존의 전위강하법에 와전류의 개념을 적용하기 위해서 주파수에 대한 결함 깊이의 영향과 결함에 대한 주파수에 대한 영향을 검토해본 결과 결함의 깊이가 깊어질수록 또한 높은 주파수에서 신호의 크기가 선형적으로 증가하는 패턴을 보였다. 연구결과 와전류를 이용하여 ACPD법을 시행할 경우 데이터 처리 과정과 실험 장비를 단순화 시킬 수 있어 결함 검사를 손쉽게 할 수 있을 것이라 예상된다.

Concerns on environmental issues and global warming are increasing worldwide. Environmental regulations such as Tokyo Protocol, RoHS, WEEE are also getting harder and harder and used as trade barriers. Different from other manufacturing industries, information and communication industry is basically environment friendly-low emission of harmful materials and little consumption of energy. But information and communication industry can contribute to world environment by recycle articles in disuse and properly process discarded trash. Furthermore, by using more renewable energy, it can reduce the $CO_2$ emission, one of the major the green house gas.

본 논문에서는 전자기파 산란 문제를 해석하는데 있어서 중요한 기법의 하나인 유한 차분 시간영역 해석방법(FDTD : Finite-Difference Time-Domain Method)을 이용하여 금속 차폐구조의 틈새인 개구를 통한 EMC 문제를 중점적으로 다루었다. 이와같은 3차원 FDTD를 이용한 전자파 산란 문제의 해석을 통한 연구는 통신 시스템의 차폐 방안과 전자파 내부침투 문제 해결을 위한 중요한 기반 작업이 될 것으로 기대된다.

Mobile WiMAX(WiBro)를 비롯한 통신서비스는 정지 및 이동 중에도 다양한 형태의 휴대 단말기를 이용하는 가입자에게 음성 및 데이터 서비스를 제공하기 위한 양질의 QoS와 Seamless mobility를 보장하는 무선망의 구축이 필요하다. 무선망 구축을 위해서는 년도별/지역별 트래픽 수요예측 분석과 서비스 대상 지역에 대한 사업 단계별 망 구축 및 확장 시나리오에 따른 투자비의 산출과 양호한 서비스 품질을 보장하기 위한 무선망 설계가 선행되어야 한다. 본 논문에서는 무선망설계 절차 및 무선서비스사업자의 경제적인 무선망 구축을 위해 필요한 무선망설계툴 운용방안에 대해 알아보고, 노미널 설계, 상세 설계, 그리고 망운용 및 최적화에 필수적인 KT가 자체 개발하여 휴대인터넷 망설계에 사용한 무선망설계툴 CellTREK의 최근 기능에 대해서도 간략하게 소개한다.

There are three main kinds of service standards for 3G(Third-Generation) wireless communication as WCDMA, CDMA2000 and TD-SCDMA(Time Division-Synchronous Code Division Multiple Access). Compare with WCDMA and CDMA2000, TD-SCDMA system has distinguished technical characters. It is a TDD(Time Division Duplexing) based technology and deploys several advanced but in some respects complex technologies such as smart antenna, joint-detection and baton-handoff, etc. Therefore to analyze and design TD-SCDMA wireless network, it needs more efficient and systematic simulation tool. General simulation tool has so many analysis functions including path loss prediction, capacity and coverage analysis. For more suitable for TD-SCDMA, new additional technologies have to be implemented in simulation tool. Especially as the wireless network highly advancing focused on data service, it more needs to research and develop on the reliability of the simulation tool. In this paper, to give the concrete process and skill about how to implement TD-SCDMA simulation tool, we define the kinds of simulation tool and list basic analysis functions available for TD-SCDMA network design at first. And then we explain how to consider the effects of new technologies of TD-SCDMA and give the solutions about theses considerations.

In this paper, propagation analysis method in using 3D Ray Tracing propagation model in wireless cell planning is proposed. Through 3D Ray Tracing model, we can predict the distribution of propagation loss of the received signal. For correct and a low complex analysis, Quad Tree and Pre-Ordering and Hash Function algorithms are included in 3D Ray Tracing algorithm. And 3D Ray Tracing model is embodied in CellTREK that is developed by KT and used to plan Wibro system analysis. In CellTREK, propagation analysis is performed and that result is represented in 3D viewer. In numerical results, it is showed that the proposed scheme outperforms Modified HATA model when comparing with measurement data.

Multicast and Broadcast Service (MBS) provides flexible and efficient transmission of the same information to multiple users using shared radio resources on WiBro network. The advantage of this service is to achieve the most efficient use of radio and network resources as well as to lessen sender's processing load when sending the same information to multiple users. Though radio resources are saved since a multicast or broadcast transport connection is associated with a service flow, it is hard to change MBS service channel dynamically. In this paper, we propose a Radio Resource Management System (RRMS) for supporting dynamic scheduling of MBS service channels. Results show that our proposed scheme using Radio Resource Allocation Table (RRAT) can efficiently support MBS services by providing dynamic schedule for MBS service channels.

무선 사업자가 각자의 네트웍 기반으로 제공하던 유무선 통신서비스는 무선사업자들은 음성서비스에 의한 유선서비스 대체(FMS)로 나타나고 있으며, 유선사업자들은 All-IP 기반의 NGN 진화에 따라 유선사업자 중심으로 유무선 서비스 통합(FMC)이라는 형태로 진화하고 있다. 초기의 FMC는 하나의 단말기로 실내의 유선서비스와 실외의 무선서비스를 Seamless 보장없이 제공하였으나, 유선전화(PSTN)의 무선랜 기반 VoIP 진화 등에 의해 무선랜-CDMA 듀얼폰 기반의 FMC Seamless 서비스를 유무선 사업자들이 준비 중에 있다. Seamless 서비스를 위한 이동성기술은 네트웍 기반에서 음성/데이터 이동성을 제공하는 기술(UMA/UNC)을 유럽에서 상용화 서비스 중이며 최근 플랫폼 진화(IMS)로 IMS/VCC기반의 음성이동성 기술이 개발되고 있으며 향후 유무선 사업자간의 IP 기반 서비스를 위한 이동성 기술 또한 다양한 기술들이 표준화 중에 있다. 이에 본 논문에서는 이러한 음성/IP이동성 기술에 대한 고찰을 통해 무선랜 중심으로 듀얼폰 기반의 이동성 기술 적용 방안을 고찰코자 한다.

This article presents the performance evaluation case study of circuit-switched WCDMA R5MSC(Mobile Switching Center) Server and CS-MGW(Circuit Switched Media Gateway) in 3'rd generation mobile telecommunication (UMTS : Universal Mobile Telecommunication System). The presented work adopted circuit switching scenarios recommended by 3GPP(Third Generation Partnership Project) and terrestrial spectrum calculation parameters and its values defined in ITU-R M.2023 and M.1390 to do the case study on performance evaluation of circuit switched system (R5 MSC Server and CS-MGW) in WCDMA core network. This paper describes test results by using simulator which substitutes for wireless section (MS, Node-B, RNC).

In order to expand cell coverage, increase system capacity, and offer various multimedia service with high throughput in indoor environment, WiBro Access Point(AP) is developed. Home AP is IFA/Omni type and has stack-up structure of channel card and RF board. SOHO AP is designed to support up to 2FA and has remote RF(RRF) structure using UTP method. Inter-operational test with mobile terminal were completed for 3 terminals using web browsing service simultaneously. The performance test results of WiBro AP are as follows: RCE(EVM) value is -34.431 dB for 64-QAM and throughput is up to 6.79 Mbps(DL) and 1.1 Mbps(UL) with 2.5m Line-of-Sight(LOS) condition.

In the next generation wireless mobile network, various methods are studied to offer interworking and mobility between various radio networks. To offer these harmoniously, network adaptation methods based on IP is generalized, and specifications of host-based mobility method with Mobile IPv4 and Mobile IPv6 to offer IP's mobility are defined in IETF specially. However, it is insufficient to satisfy quality of service that should be offered in wireless mobile network environment. Alternatively studies about Network-Based Mobility of Proxy Mobile IPv4, Proxy Mobile IPv6 etc. are preceded. This paper presents optimum plan that can offer mobility in the next generation radio transfer communication network by comparing and analyzing IP mobility methods divided by Host-based Mobility and Network-based Mobility.

Typically a wireless sensor network consists of a number of nodes that sense surrounding environment and collaboratively work to process and route the sensing data to a sink or gateway node. We propose an architecture with support of multiple routers in IPv6-based Low-power Wireless Personal Area Network (6LoWPAN). Our architecture provides traffic load balancing and increases network lifetime as well as self-healing mechanism so that in case of a router failure the network still can remain operational. Each router sends its own Router Advertisement message to nodes and all the nodes receiving the messages can select which router is the best router with the minimum hop-count and link information. We have implemented the architecture and assert our architecture helps in traffic load balancing and reducing data transmission delay for 6LoWPAN.

This article presents the change characteristics of induced noise whether the sheath layer of the cable is grounded or not. As what affects the induced noise, there are power influence or longitudinal transverse voltages and its weighted filtered voltage. The sheath ground is basicaly predicted to have the effects of alleviation on the power influence. But practically the effects may not happen in the case of common cable's sheath layer. Rather there are cases that the ground of sheath affects so that the noise level could increase. So we need to scrutinize the effects of the sheath gorund in the measures for the protection against electromagnetic induction by powerline or traction line system. And the evaluation of using the designated shielding purpose cable is needed.

FTTH (Fiber to the Home) is constructed with optical devices and optical cables from central office (CO) to subscribers. With FTTH, it is possible to provide service platform in order to meet the customers' emerging demands for more bandwidth/security and diverse IP multimedia applications including high definition (HD) video streaming service. FTTH can provide enough bandwidth from 100Mbps to several Gbps per subscriber. It is also most appropriate network architecture for convergence of communication and broadcasting. So, FTTH is thought the final destination of telecom operators, since it is the fastest and most reliable solution so far and various IP multimedia services are possible through it. In this paper, newly attempted technologies of FTTH construction for apartment complexes using CWDM-PON system are discussed.

OSP 에서 주로 사용되는 Drop Cable 은 통신단말인 단자함에서 통신전주 두상에 설치된 인입클램프 걸이에 인입클램프를 취부하고, 가공구간을 통해 가입자 댁으로 가설을 하며, 가입자 댁의 일정한 지점에 인입벽철 또는 인입용 훅을 설치하고, 인입클램프를 체결하여 Drop Cable 의 이도 및 루트를 고려하여 개통공사를 완성하여 해당서비스를 공급하게 된다. 이때, 사용되는 Drop Cable 은 일반적으로 자기지지를 할 수 있는 "8" 형태의 자기지지형 Drop Cable 을 주로 이용하였으나, 광섬유를 이용하는 FTTH 사업에서는 서비스 개통시 "0" 형태의 Optical Drop Cable(광옥외선)을 사용하여 개통작업의 시공성 및 생산성을 향상 시켰다. 이에 사용되는 적합한 인입광 클램프는 광옥외선의 외형적인 구조에 손상을 전가하여서는 안되며, 광옥외선 내부의 광섬유에 손상을 가하지 않는 최소의 손실을 가지며, 일정한 인장력을 유지하고 있어야 한다. 따라서, 위의 사항을 고려한 인입 광클램프의 특성에 대해 고찰하고자 한다.

2007년 1월 20일 20시 56분경 오대산 부근에서 발생한 지진이 제주도를 제외한 전국에서 감지되어 우리 생활에 직접적인 영향을 끼치는 등 더 이상 우리나라도 지진에 안전한 나라가 아니라는 것이 입증되고 있으며, 정부에서도 자연재해대책법에 통신설비에 대한 내진설계 의무화 규정을 포함시켜 현재 시행을 눈앞에 두고 있는 시점에서 통신시설물에 대한 내진성능 평가와 내진대책 수립이 절실히 요구되고 있다. 따라서, 본 논문에서는 지진 발생시에 가장 민감하게 반웅하며 피해가 클 것으로 예상되는 통신 장치랙에 대하여 전력설비의 내진성능 검증에 사용되는 인공 지진파와 미국에서 측정한 실측 지진파를 진동대에 입력, 지진모사 실험을 실시하여 지진시 발생할 수 있는 통신장비의 기능 이상 유무를 확인하고 동적 거동 특성을 분석함으로써 장치랙이 보유한 내진성능을 도출하여 보았다. 이러한 지진모사 실험은 향후 통신 장치랙의 내진성능을 평가하는 기준을 수립하는데 중요한 기초자료로 활용될 것이라 판단된다.

현재 통신용 강관전주는 상, 하로 2 분할된 강관을 조립하여 대부분 사용하고 있다. 콘크리트전주에 비해 가볍고, 길이가 짧기 때문에 도심지 등 협소한 지역에서도 시공이 가능하며 특히 소규모 인력으로 시공이 가능하다. 하지만 전주의 단면이 작아 별도의 기초 보강을 하지 않고서는 지반의 지지력이 부족하여 전주가 기울어지거나 전도되는 현상이 빈번히 발생하고 있으며, 또한 운반을 용이하게 하기 위하여 2 분할한 강관의 조립 부분에서의 꺽임 현상이 발생하여 도시 미관을 해치고 있는 실정이다. 통신전주의 안정성을 확보하기 위해서는 전주 자체가 보유한 강도를 발휘할 수 있도록 충분한 지반지지력이 확보되어 있어야 한다. 강관전주의 휨강도 실험 및 현장 지반지지력 실험을 통해 충분한 지반지지력을 확보할 수 있는 공법을 도출해 내고, 현재 강관전주의 지반지지력 보강을 위해 사용하는 콘크리트블록 설치 방식이 아닌 시공 편리성 및 안정성을 개선한 기초콘크리트 방식을 제시하고자 한다.

지하구에는 국 가의 신경이라 할 수 있 는 전력, 통신, 상수도 등 주요시설물들이 수용되어 있으며, 지 하구는 화재, 집중호우에 의한 침수, 외부침입 등의 재난에 항상노출되어 있다. 2006년 12월에 발생된 구리 전력구 화재와 2000년 여의도 공동구 화재 등에서 보듯이 화재가 발생하면 화염과 연기, 유독가스로 인해 내부로 진입할 수 없으므로 조기경보 및 조기 대처가 매우 중요하다. 따라서 본 논문에서는 지하구 중에서 통신케이블을 수용하는 통신구의 재난에 조기 대처할 수 있는 통신구 원격감시 시스템에 대해 기술하고자 한다. 통신구 원격감시 시스템은 통신구내의 침입, 침수, 화재 등을 모니터링하여 재난을 미연에 방지할 수 있도록 하고, 각 감지기 및 장치에 설정된 임계치를 초과한 경우 경보 현황을 운용자에게 알려 신속하게 조치할 수 있도록 하였으며, 시스템의 안정성과 확장성, 유지보수의 용이성 등을 고려하여 통합/분산 서버, 데이터 수집장치, 감지기 등 으로 구성 하였고, 시스템간의 연동과 호환성을 위해 표준화된 통신 프로토콜을 사용하였으며, 필요에 따라 감지기 및 장치를 수정, 추가할 수 있도록 개발하였다. 그리고 이를 검증하기 위해 부산지역의 지하철병행통신구 3.8km에 대해 시범설치하여 운용함으로써 시스템의 안정성, 운용성 등에 대해 검증하였다.

우리는 가끔 도로상에 설치되어 있는 맨홀뚜껑이 뒤집혀 있는 것을 보거나, 맨홀뚜껑 이탈로 인한 차량 파손 소식을 접할 수 있다. 맨홀뚜껑은 일반적으로 도로나 보도에 많이 설치되어 있고, 현재 사용중인 KS규격의 맨홀뚜껑은 마모 및 충격 등 여러 가지 복합적 요인으로 인하여 소음이 발생하고, 또한 극히 일부는 도로에서 이탈하여 인적, 물적 피해를 발생시키고 있는 실정이며 이를 방지하기 위해 많은 연구와 제품 등이 만들어 지고 있는 실정이다. 본 연구에서는 KS규격 맨홀뚜껑의 정적 및 동적 특성을 각종 해석프로그램과 진동실험을 통해 분석하였고, 파라미터 해석을 통한 거동의 핵심 요소 등을 확인하였다. 이러한 분석결과는 보다 안전하고 경제적인 맨홀뚜껑을 개발하는데 중요한 기초자료로 활용될 것이라 판단된다.

지하에 설 치된 맨홀의 구조물이 노후되거나, 내부에 수 용된 시설물로 작업 공간이 협소하여 맨홀 구조물을 대개체 할 펼요가 있을 경우, 지금까지는 대부분 현장 콘크리트 타설에 의한 방법을 사용하였다. 이러한 방법은 거푸집 시공, 콘크리트 타설, 콘크리트 양생, 거푸집 철거 등의 공정이 소요되어 공사 기간이 장기화 되고, 도심지에 위치한 맨홀인 경우에는 차량과 보행자의 통행 불편을 초래하기도 하였다. 또한, 통상적으로 사용되고 있는 프리캐스트 맨홀에 비해 시공 품질이 낮아 향후 맨홀의 운용 및 유지관리에 많은 어려움을 겪는 원인이 되기도 하였다. 본 논문에서는 이러한 문제점들을 해결하기 위해, 폴리머 콘크리트를 이용하여 하부, 벽체, 상부로 구성된 다수의 세그먼트를 생산한 후, 현장에서 이들 세그먼트를 조립하여 맨홀을 설치하는 방법을 연구하였다. 가변형 거푸집을 이용한 세그먼트 제작과 조립식 블록에 의한 관구를 사용하여 현장 적용성을 높임은 물론, 프리캐스트로 생산되는 폴리머 콘크리트 맨홀 수준의 시공 품질을 확보할 수 있도록 하였다.

Mobility Anchor Points are used for the mobility management in HMIPv6 networks. Currently a mobile node selects the MAP farthest away from itself as a new MAP among available candidates when it undertakes a macro handoff. With this technique, however, the traffic tends to be concentrated at a MAP with the largest domain size and the communication cost increases due to the distance between the mobile node and the MAP. In this work, we proposed a cost effective MAP selection scheme. When leaving the current MAP domain. the mobile node calculates the optimum MAP domain size to minimize the local mobility cost at the new MAP domain considering mobile node's velocity and packet transmission rate. The mobile node then selects a MAP domain of size close to the optimum domain size calculated among the candidate MAP domains. In this way, it is possible for the mobile node to select an optimal MAP adaptively taking the network and node states into account, thus reducing the communication cost.

This article discusses a capacity planning method in QoS-guaranteed IP networks such as BcN (Broadband convergence Network). Since IP based networks have been developed to transport best-effort data traffic, the introduction of multi-service component in BcN requires fundamental modifications in capacity planning and network dimensioning. In this article, we present the key issues of the capacity planning in multi-service IP networks. To provide a foundation for network dimensioning procedure, we describe a systematic approach for classification and modeling of BcN traffic based on the QoS requirements of BcN services. We propose a capacity planning framework considering data traffic and real-time streaming traffic separately. The multi-service Erlang model, an extension of the conventional Erlang B loss model, is introduced to determine required link capacity for the call based real-time streaming traffic. The application of multi-service Erlang model can provide significant improvement in network planning due to sharing of network bandwidth among the different services.

방송과 초고속인터넷 서비스를 동시에 제공할 수 있는 HFC(Hybrid Fiber Coaxial) 망은 상/하향이 비대칭 구조이며, 하향속도에 비해 상향속도가 1/10 수준이어서 상향 트래픽이 과다하게 생성될 경우 인터넷속도 지연이 발생한다. 지연에 민감한 VoIP 서비스의 품질보장 방안으로는, DOCSIS(Data Over Cable System Interface Specification) 1.1 기반의 상향 스케쥴링 기능을 이 용한 VoCM(Voice Over Cable Modem)이 있다. 그러나 별도의 VoCM을 사용해야 하며 아날로그 전화기를 사용해 IP 기반의 VoIP 단말을 사용할 수 없다는 단점이 있다. 일반 CM(Cable Modem)에 DOCSIS 1.1 Config File을 이용하여 VoIP 품질을 보장할 경우 별도의 트래픽 대역을 항상 점유해야 하는 단점이 있다. 이에, 본 논문에서는 효율적 대역폭 이용과 단말장비에 종속적이지 않은 방안을 제안하고 일반 CM을 통한 유무선 환경하에서 Dynamic QoS(Quality Of Service)를 제공할 수 있는 PCMM(Packet Cable MultiMedia) 적용 방안 및 시험결과에 대해 고찰하고자 한다.

This paper proposes a multicast scheme over IEEE 802.16 networks which support multiple upper layer protocols such as ATM, IPv4 packets, IPv6 packets, IEEE 802.3 over IPv4 and so on. The multicast capabilities over IEEE 802.16 are important both control plane and data plane. The proposed multicast scheme can be divided into two types: direct mapping and indirect mapping. The direct mapping scheme is that layer 3 address is directly mapped into CID information which is used for connection identifier at IEEE 802.16 link layer. The indirect mapping scheme has two steps for mapping between layer 3 address and layer 2 CID. Firstly, a layer 3 address translates to Ethernet MAC address with group MAC address. Secondly, a group MAC address is mapped into CID. The mapping scheme depends on the upper layer protocols.

Broadband Convergence Network (BcN) can provide a range of quality guaranteed broadband multimedia services through packet-based converged transport network. For providing new emerging application services in due season over BcN, it is important for network designers or planners to develop a new design methodology for BcN, which differs from legacy design processes applied to a single service network. This paper thus introduces a new design concept and detailed design processes for KT-BcN. We also present a design example of BcN control network using a design system that we have developed.

본 논문은 주파수공용통신 시스템과 디지털 이동전화 시스템간의 양립성에 관해 분석하였다. 이 분석의 목적은 주파수공용통신 시스템의 기지국의 불요방사로부터 디지털 이동전화 시스템 이동국에 야기하는 간섭확률을 몬테카를로 방법을 이용하여 계산하여 양립성을 분석하는 것이다.

This paper presents an real-time implementation of H.264/AVC High 4:4:4 Predictive profile decoder using general-purpose processors by exploiting multi-threading technique and Single Instruction Multiple Data (SIMD) instructions without any quality degradation. We analyze differences between the existing High profile and High 4:4:4 Predictive profile decoder, and show various optimization techniques to decode high fidelity and high definition (HD) video in real-time. Simulation results show that the proposed decoder can play high fidelity HD video at average 40 frames per seconds (fps) for the IBBrBP bistream and about 50 fps for the Intra-only bitstream.

This article presents several methods of mobile communication network to access technologies utilizing unlicensed spectrum interworking. Generic Access Network (GAN) technology was already specified in GERAN (GSM EDGE Radio Access Network) and Interworking WLAN (I-WLAN) was standardized for WCDMA system for WLAN user to access WCDMA packet based services through WLAN access point. Voice Call Continuity is not access network dependent technology but is a kind of domain change scheme for voice call from Circuit Switching (CS) network to IP Multimedia Subsystem (IMS) and vice versa.

전자연동장치(Interlocking System)는 열차의 안전운행 확보와 함께 수송능력과 보호향상, 정확하고 신속한 운송과 더불어 이용률을 증대하는데 중요한 역할을 한다. 철도 신호보안 설비 중에서 그 핵심을 이루는 연동장치 설비에 첨단기술인 전자, 정보처리 및 정보전송기술을 철도 신호 시스템에 도입하여 신뢰성과 안정성이 확보된 신호설비를 구현하기 위해 최근에는 마이크로프로세서를 이용한 전자연동장치 기술이 개발되었다. 본 논문에서는 전자연동장치의 필요성 및 기존설비(기계 및 계전 연동장치)의 노후화에 따른 장애 및 호환성 결여 등의 문제점들을 해결하기 위하여 전자 연동장치와 기존 계전 연동장치의 차이점을 제시 및 문제 해결방안을 고찰하고, 전자연동장치 동향을 살펴보았다.

This paper discusses a most suitable wireless communications system for subway trains on condition that a geo-spatial video system is implemented in subway trains. Geo-spatial video system for subway trains refers to the device that can transfers the images captured by cameras within a subway station building or in and around a subway track to on coming trains wirelessly, which allows the operator in operating room to monitor the state of a platform and a subway track, the flow of passengers, and the condition of passengers getting on and off. To minimize the problem, secure civil safety and prevent accidents and calamity from occurring, a geo-spatial video system for subway trains has been increasingly introduced. The wireless communications systems for GVS for subway trains involve HF(High Frequency), IR(Infra Red), M/W(Micro Wave), wireless LAN approaches. Each has its own strengths/weaknesses, and different vendors have different technology.

In this paper, we have implemented the device management system to upgrade T-PAK software in mobile phone. The hybrid scheduling method and selective upgrade method are proposed. Hybrid scheduling method is based on distribution of delivery data in accordance with network traffic load and service priority from device management server to mobile phone. Selective upgrade method manages DSL classified by T-PAK software version to be upgrade using version management established in OMA DM SCOMO. Key mechanism of selective upgrade method is to only deliver DSL to be replaced to the mobile phone. We made an experiment on two methods using MS-700T terminals. The experimental result shows that the proposed method is faster than normal from delivery time standpoint.

This paper suggests remote injection system and explains the design of the system and means of implementation. Remote injection system means a system delivering the precise injection prescribed to the patient in the ward through input into the remote server using TCP/IP protocol. The system has been planned in detail. The syringe has been designed to be linked with the Ringer's rubber tube and the independently developed syringe-module is to be used in order to ensure precise and accurate delivery of the injected medication. In development stage of embedded software, object-oriented planning method has been chosen.

As development of wireless communication technology has promoted mobility, Location Based Service (LBS) became embossed. The LBS is a service to recognize and utilize a location of a person or a thing through a device that ensures mobility based on wireless communication network. This paper thus researches on Healthcare Method to respond to emergency rapidly by recognizing a patient's location with the LBS. The LBS also provides location information of a user as well as remote management of organism data such as ECG data or pulse, which is transferred to a hospital or an emergency room.

TV technology started from black and white TV. Color TV invented and users request more realistic TV technology. The next technology is 3DTV. For 3DTV, 3D display technology, 3D coding technology, digital mux/demux technology in broadcast and 3D video acquisition are needed. Moreover, Almost every contents now exist are 2D contents. It causes necessity to convert from 2D to 3D. This article describes 2D/3D conversion algorithm and H/W platform on FPGA board. Time difference makes 3D effect and convolution filter increased the effect. Distorted image and original image give 3D effect. The algorithm is shown on 3D display. The display device shows 3D effect by parallax barrier method and has FPGA board.

The reliability as well as the power capability of the UPS system can be increased by replacing a single UPS unit with multiple small UPS units in parallel, resulting in a so-called module UPS. This module UPS system allows that a new module can be added or replaced while maintaining power to loads, which is a hot-swappable operation. In addition, it has desirable features such as ease of output power expandability, convenience of maintenance and repair, and high reliability. To realize the module UPS, load sharing without interconnection among parallel connecting modules as well as a small scale and lightweight topology is necessary. The frequency and voltage droop method is applied to parallel operation control to achieve load sharing. 5kVA modules are designed and implemented to confirm the effectiveness of the proposed approaches. Experimental results show that the module UPS system has a high power factor, a low distortion of output voltage and input current, hot-swappable operations and good load sharing characteristics.

This thesis aims the development of power supply for the BTS of Mobile Telecommunication system. Specially, it receives AC power and it can be possible both supply the uninterrupted and stabile DC Power to BTS and simultaneously maintain full charging the back-up battery that is used in case failing AC power supply. In addition, easy maintenance is also the main purpose of it regardless of front and left side except rear side. In these days, it needs more small size power supply system in order to comply with the user needs regarding more easy maintenance and more less space as become smaller main telecommunication systems. This system can be installed close to wall and support more easy maintenance and it was considered easy expansion in case when it needs.

⇒ 초록(영문) 입력자 : This document defines JSR298 Telematics API for Java ME. The main purpose of JSR298 is to be able to provide automotive telematics services through use of this specification on embedded devices that are using Java ME platform. The goal is to standardize specification in order to provide automotive telematics services using embedded devices with Java ME as their base platform. This specification defines methods for controlling and obtaining diagnostic information and conditions on various components built in to the vehicle. Therefore, this document will provide specifications required for controlling various equipments built into the vehicles as well as obtaining diagnostic information on these components and vehicle conditions. Automotive components are defined as equipments that are accessible for drivers including airbag, door, window, and brake. This specification is applicable to telematics-specific automotive terminals as well as other various portable devices including cellular phones and PDAs.

In the RRH (Radio Remote Head) of a WCDMA Node B System, an HPA (High Power Amplifier) is used in order to amplify the transmission RF signal. Upon designing an HPA, the design requirements demand that the intermodulation characteristics are optimized during design and that the stability of the characteristics is maintained in the field. In this DOE (Design of Experiments) research, a few vital factors that affect intermodulation characteristics were first selected; then, an optimal solution was produced for high reliability in a noisy environment in the field by employing the Taguchi Method, a statistical method used for a robust design. Furthermore, by employing HALT(High Accelerated Life Test) during the verification test, this experiment has verified that an HPA that was designed using the Taguchi Method proved to be a far more robust design than an HPA that was designed without using the method.

In this paper, we studied on characteristic improvement of Balun-BPF using dual-mode ring resonators. The simulated Balun-BPF shows bandwidth of 150MHz at center frequency of 2.45GHz, 4-pole characteristic, return loss of 15dB and symmetrical out-put characteristic.

This paper presents the design and analysis of LNA-Mixer for 2.45GHz RFID reader. The LNA is implemented by PCSNIM method for low power consumption. The Mixer is implemented by using the Gilbert-type configuration, current bleeding technique, and the resonating technique for the tail capacitance. The connection between the two designed circuits is made by active balun. This LNA-Mixer has about 35dB for -40dBm input RF power, LO power is 0dBm and RF frequency is 2.45 GHz and IIP3 is -4dBm. The layout of LNA-Mixer for one-chip design in a $0.18-{\mu}m$ TSMC process has 2.6mm ${\times}$ 1.3mm size.

This paper, designed UWB elliptical slot antenna and analysis based on the distribution of the electromagnetic fields pattern and resonant mode of designed antenna is presented. Designed antenna is fabricated on FR4 substrate with thickness of 1.524mm and relative dielectric constant 4.4. The measured bandwidth of $3.6GHz{\sim}20GHz$ for VSWR<2. Through the field pattern and resonant mode analysis that the slot antenna operates on a series of the multi-pole radiation based on TE modes matched to system impedance. And the perfect magnetic wall is along the axis of symmetry on the y-z plane. This result gives us an easier method to design the similar antennas, which is the impedance matching to the system impedance after once constructing a proper structure with a series of multi-mode resonances.

An active Balun is designed for RFID reader at 2.45GHz. The Balun is integrated inside the receiver, then the LNA and mixer can be connected. The unbalanced LNA output signal is transformed to a balanced signal at the input mixer The RF mixer and LO mixer, by using this balun. The Balun provided a balanced signal with two output stage, gain mismatch is 0.116dB. The phase show a good behavior with $163.918^{\circ}$,$-16.609^{\circ}$. The phase mismatch is about $0.527^{\circ}$. The tight difference between the gain and phase on each brancd, is because of the used capacitor and integrated inductor and the other parasitic element inside the balun.

Applications in present-day mobile communication systems particularly require miniaturized dimensions and low-profiles of antenna in order to meet the mobile units. Thus, size reductions and bandwidth enhancements are becoming crucial design considerations for practical applications of microstrip antennas. The motivation of further experiments have been stepped to follow those studies for achieving compact and broadband, even multiplied operation modes, which are greatly increased with much attentions recently. To obtain broadband, single-feed, circularly polarized characteristics of microstrip antennas, a design with feed-line ought to be a factor of two. Usually, diagonally balanced-line feeds with hybrid coupler are employed to attain circular polarizations. We firstly formulated DGS (Defected Ground Structures) based operation principles of the entire microstrip components and therefore were able to derive impedance variance of feed-lines. After verifying corresponding experimental results, we targeted the frequency bands of UHF RFID (Ultra High Frequency Radio Frequency IDentification) and approximately of 0.4-2.4GHz have exhibited remarkable two resonance amplitudes as a dual band antenna. Our secondary researches were aimed to design quad band microstrip antenna which represents four resonance characteristics within the identical frequency bands as well. Microstrip patch has been meandered to lengthen the electrical paths, and the other design criteria with respecting physical parameters including radiation patterns and impedance bandwidths measurements will be described for verification. Advisable applications of these antennas can be GSM850, GSM900, GPS (L1-1575 and L2-1227) and UMTS-2110 of cellular systems, which extremely desire multiband and minimum size.

In this paper, a dual band microstrip patch Antenna is designed for RFID Application. The antenna shows a good performance at the frequencies, 900MHz and 2.45GHz for the radiation characteristics and input impedance matching, as well. The reflection factor is lower than -25dB and a good directivity higher than 5dB is achieved for both frequency.

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

As the mobile communication service is widely used, the demand for wireless repeaters is rapidly increasing because of the easiness of extending service areas. But a wireless repeater has a problem that the output of the transmit antenna is partially fed back to the receive antenna, which results in feedback interference. In this paper, we propose a new varable step-size LMS algorithm, which utilizes correlation between reference and error signals to adjust the step sizes, for cancelling the feedback interference signals in the WCDMA repeater under time-varying multi-path channels. The proposed algorithm was investigated through computer simualation by being applied to the time-varying channels. The simulation results demonstrated that the proposed one is superior to the conventional ones in terms of cancelation perormance.