The $ZnNb_2O_{6}$ ceramics with CuO(1, 3, 5wt%) were prepared by the conventional mixed oxide method. The ceramics were sintered at the temperature of $950^{\circ}C$∼$1075^{\circ}C$ for 3hr in air The structural properties and the microwave dielectric properties of $ZnNb_2O_{6}$ ceramics were investigated with sintering temperature and the addition of CuO. Increasing the addition of CuO, the peak of second phase($Cu_3Nb_2O_{8}$) was increased. The grain size of the $ZnNb_2O_{6}$ ceramics with CuO was increased with CuO addition at same temperature. The dielectric constant of $ZnNb_2O_{6}$ ceramics with CuO was increased with sintering temperature and CuO addition. While the quality factor of the $ZnNb_2O_{6}$ ceramics with lwt% CuO depended on sinterability, the quality factor of $ZnNb_2O_{6}$ with 3wt% and 5wt% CuO depended on second Phase due to the CuO addition. The optimum dielectric Properties of $\varepsilon$$_{r}$ = 21.73 Q${\times}$f = 19,276 were obtained from the condition of 3wt% CuO addition and sintering temperature of $1025^{\circ}C$(3hr).

The composites were fabricated, respectively, using 61vol.% SiC - 39vol.% TiB$_2$ and using 61vo1.% SiC - 39vo1.% WC powders with the liquid forming additives of 12wt% $Al_2$O$_3$＋Y$_2$O$_3$ by pressureless annealing at 180$0^{\circ}C$ for 4 hours. Reactions between SiC and transition metal TiB$_2$, WC were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H), TiB$_2$ and YAG(Al$_{5}$Y$_3$O$_{12}$) crystal phase on the SiC-TiB$_2$, and SiC(2H), WC and YAG(Al$_{5}$Y$_3$O$_{12}$) crystal phase on the SiC-WC composites. $\beta$\$\longrightarrow$$\alpha$-SiC phase transformation was ocurred on the SiC-TiB$_2$, but $\alpha$\$\longrightarrow$$\beta$-SiC reverse transformation was not occurred on the SiC-WC composites. The relative density, the vicker's hardness, the flexural strength and the fracture toughness showed respectively value of 96.2%, 13.34GPa, 310.19Mpa and 5.53Mpaㆍml/2 in SiC-WC composites. The electrical resistivity of the SiC-TiB$_2$ and the SiC-WC composites is all positive temperature coefficient resistance(PTCR) in the temperature ranges from $25^{\circ}C$ to 50$0^{\circ}C$. 2.64${\times}$10-2/$^{\circ}C$ of PTCR of SiC-WC was higher than 1.645${\times}$10-3/$^{\circ}C$ of SiC-TiB$_2$ composites.posites.

A new 600 V dual gate transistor employing thyristor action, which incorporates floating PN junction and trench gate IGBT, is proposed to improve the forward current-voltage characteristics and the short circuit ruggedness. Our two-dimensional numerical simulation shows that the proposed device exhibits low forward voltage drop and eliminates the snapback phenomena compared with conventional trench gate IGBT and EST The proposed device achieves high current saturation characteristics by separating floating N+ emitter and cathode. The proposed device achieves low saturation current value compared with conventional devices, and the short-circuit ruggedness is improved. The proposed device may be suitable for the use of high voltage switching applications.

In this Paper, a flashover prediction method using the leakage current in the contaminated EPDM distribution polymer insulator is proposed. The leakage currents on the insulator were measured simultaneously with the different salt fog application such as 25g, 50g, and 75g per liter of deionized water. Then, the measured leakage currents were enveloped and transformed as the CDFS using the Hilbert transform and the level crossing rate, respectively. The obtained CDFS having different gradients(angles) were used as a important factor for the flashover prediction of the contaminated polymer insulator. Thus, the average angle change with an identical salt fog concentration was within a range of 20 degrees, and the average angle change among the different salt fog concentrations was 5 degrees. However, it is hard to be distinguished each other because the gradient differences among the CDFS were very small. So, the new weighting value was defined and used to solve this problem. Through simulation, it Is verified that the proposed method has the capability of the flashover prediction.

The metal halide lamps are now widely used in the application and commercial lighting due to their attracting properties such as good color rendering and high efficiency. But, they have the serious problem of acoustic resonance for high frequency operation and they need the high voltage to ignite. So, they have not been applied to indoors. Over the past few years, a considerable number of studies have been conducted on the electronic ballast together with hot restarting and resonance phenomenon. But, Very few attempts have been made with the adaptive ignition method according to the lamp state. In this paper, electronic ballast is proposed for metal halide lamps with an igniter for adaptive ignition. The proposed electronic ballast can generate different ignition voltages according to the arc tube state.

A discharge plasma reactor using a ferroelectric pellet packed bed is now used as a removal means of pollutant gases, such as NOx, SOx and VOCs. When an ac voltage is applied to this plasma reactor, then the pellets are polarized, and great electric fields are formed at each top and bottom contact points of the ferroelectric pellets. Thus the points of each pellet become covered with intense corona discharges, where an electrophysicochemical reaction is taking place strongly However these strong discharges also elevate the temperature of the pellets greatly and concurrently decrease the output ozone generation, as a result, the overall removal efficiency of gas becomes decreased greatly A new configuration of discharge plasma reactor using a ferroelectric pellet layer and a wire-to-wire electrode has been proposed and investigated experimentally. It is found that an intensive microdischarge is taking place on the surface of ac corona-charged ferroelectric pellet layer of the proposed reactor, which concurrently enhances the efficiency of plasma generation greatly And, this type of configuration of plasma reactor utilizing a wire-to-wire electrode and a ferroelectric pellet layer could be used as one of effective plasma reactors to remove pollutant gas.

A study has been made of surface modification of organic materials by ion implantation to increase the surface electrical properties. The substrate used were PET(polyethylene teraphtalate). N$^{＋}$, Ar$^{＋}$ implantation was peformed at energies of 40 keV and 50 keV with fluences from $5{\times}10^{15}$, $1{\times}10^{16}$,$7{\times}10^{16}$, $1{\times}10^{17}$/ ions/$cm^2$. UV/Vis, FT-IR and XPS spectroscopy measured for surface structure changes. Surface resistance decrease of implanted polymers was affected by ion implantation energy, ion species and ion dose rate. Surface conductivity of PET increased $2{\times}10^{9}$/∼$2{\times}10^{10}$/$\Omega$/sq by ion implantation. Result of various spectroscopy analysis, the cause of increasing PET surface conductivity was expected to breaking C=O bonds. It was formation carbon network structure by promote cross-linking and create C-C, C=C bonds.

Diamond films were deposited on the cemented tungsten carbide WC-Co cutting insert substrates by using both microwave plasma chemical vapor deposition(MWPCVD) and radio frequency plasma chemical vapor deposition (RFPCVD) from $CH_4$$-H_2$$-O_2$ gas mixture. Scanning electron microscopy and X-ray diffraction techniques were used to investigate the microstructure and phase analysis of the materials and Raman spectrometry was used to characterize the quality of the diamond coating. Diamond films deposited using MWPCVD from $CH_4$$-H_2$$-O_2$ gas mixture show a dense, uniform, well faceted and polycrystalline morphology. The compressive stress in the diamond film was estimated to be (1.0∼3.6)$\pm$0.9 GPa. Diamond films which were deposited on the WC-Co cutting insert substrates by RFPCVD from $CH_4$$-H_2$$-O_2$ gas mixture show relatively good adhesion, very uniform, dense and polycrystalline morphology.

In this paper, the four-pole elliptic function microstrip filter at 2.4GHz band with fractional bandwidth of 4% is realized using compact miniaturized hairpin resonators. The parallel algorithm FDTD method is used to analyze S-parameter of hairpin resonator filter more accurately, and to calculate the electric coupling and magnetic coupling among the hairpin resonators. Absorbing boundary conditions for mesh termination used Sulivan's simplified PML and the FDTD code was paralleled by MPI for IBM SP2 which had enhanced calculation speed. The experimental measurements are performed by HP8720D vector network analyzer. Measured results on fabricated hairpin type cross coupled bandpass filters show good agreements with theoretic results.