A new three-dimensional transition solid elements was presented for the automated three-dimensional adaptive h-refinement where the steep stress gradient exists. To be consistent with 8-node solid element with nonconforming modes in accuracy, these transition elements were improved through the addition of the associated nonconforming modes. Numerical examples show that the performance of the element and the applicability to 3D adaptations are satisfactory.

An Analytical study of shear locking is introduced for linear thick beam element. The appropriate sampling point which eliminate shear locking phenomenon was Proposed through this study. Reduced integration point is exactly same as the sampling point obtained from this study. Numerical example indicates how shear locking is serious. some solutions for shear locking are presented.

The p-version crack model based on integrals of Legendre polynomial and virtual crack extension method is proposed with its potential for application to stress intensity factor computations in linear elastic fracture mechanics. The main advantage of this model is that the data preparation effort is minimal because only a small number of elements are used and the high accuracy and the rapid rate of convergence can be achieved in the vicinity of crack tip. There are two important findings from this study. Firstly, the limit value, the strain energy of the exact solution can be estimated with successive three p-version approximations by ascertaining the approximations is entered the asymptotic range. Secondly, the rate of convergence of p-version model is almost twice that of h-version model on the basis of uniform or quasiuniform mesh refinement for the cracked panel problem subjected tension.

Precast large panel structures behave differently form frame and monolithic wall structures under external loads, because of the distinct planes of weakness in the horizontal and vertical joints between panels. These joints may slide and open during shaking, producing large localized changes in the bending and shear stiffness of individual walls. The structural behavior of large precast panel buildings depends on the relative strength and stiffness of the panels and joints. Special modeling are thus required for the analysis of precast panel connections. This study suggests a new analytical modeling and method to obtain the rational estimation of discontinuity and slip movements form the connections of precast large panel structures .

There are a lot of linear dynamic analysis methods for complex structures. Each method has advantages and shortcomings. Method of dynamic analysis for complex structure is selected considering characteristics of dynamic loading, computer facility available number of degree of freedem and accuracy of results. It is a main point of view to get economical results rather then accurate ones for analysis of general complex structures, Mode superposition method and direct integration method are generally used. However, the characteristics of load is not considered in mode superpositon method, the personal computer cannot be used in direct integration methods. To over-come these shortcomings, the component mode method incorporating Ritz algorithm updated is proposed to solve economically dynamic behavior of the structures. The purpose of study is a formulation of algorithm, and computer programing suitable for dynamic analysis of the complex structure in personal computer environment.

Evaluation of structural stability of aged wharf structure of pier type is of great importance for both safety and rehabilitation, Series of field dynamic experiments were performed for berthing impact and the results were used to calibrate analysis model. Through dynamic analysis for design, berthing impact safety of old wharf structure were evaluated. In this paper the procedure and results of experiments and analysis are presented.

Nonlinear equation of motion due to material nonlinearity of structure is transformed to linear equation of motion by treating the nonlinear elastic force term as an applied force. The solution in a time step is carried out by iterative linear dynamic analysis. The present simple algorithm is varidated by several examples .The results show that this algorithm is and efficient.

A computer program for free vibration analysis of plane framed structures has been developed by object oriented programming technique using C" language. The object oriented programming concepts such as object, class, method and inheritance are represented. The static and free vibration analyses for framed structures were satisfactorily performed by this program which consists of TOP, VECTOR, MATRIX, STRU, GUI and other classes. Numerical test shows the validity and capability of the present study which can be expandable to develop a general purpose object oriented finite element analysis program of structures ,res ,

This study serves as a part for the development of an integrated structural design system. Efficient data management is essential in engineering computer applications where the volume of data is large and the data flow and sharing are required. From a viewpoint of computer application, building structures can be considered to be a mass ofdata. The centralized database(CDB) and database management system frees the application from the details of managing data storage and retrieval while providing a common pool of information. For this, systematic information analysis and modeling have to be preceded. In this paper we described the result of database modeling of building structure.

An integrated structural design system can define and process complex design information that occurs in each of the design stages for flexible cooperation. It can also reduce human error on sequential design steps: preliminary design, analysis and detailed design. Therefore, it's very important to have consistent semantic expression and procedure for structural design information that has complex relationships. In this study, we introduce the object-oriented concepts and object-oriented database thechnique that provides high level semantic expression in order to develop an integrated structural design system.

The study summarized in this paper is concerned with the buckling of a longitudinal bar in reinforced concrete members by numerical analysis method. The objectives of this study are to investigate the stress transfer mechanism between concrete and reinforcment and to propose a modeling equation. The result gives an acceptable agreement between the proposed modeling equation and the computer package as follows: (1) the proposed equation is a possible prediction of the strain softening of concrete and reinforcement buckling. (2) the buckling of longitudinal bars is mainly influenced by the spacing of hoops and the location of the bar.

Conventional tuned mass dampers are located on the top floor of tall buildings, which reduce the fundamental mode response of buildings. Higher modes may have a greater contribution toward the acceleration response of tall buildings. To reduce this, additional tuned mass dampers are required and could be substituted as building equipments. This paper shows, with a numerical ezample, how the lecate tuned mass damper in order to reduce the higher mode response effectively

A simplified dynamic analysis method for high-rise building structures is proposed in this study. In the proposed method, member forces are obtained through static analysis using story forces derived from story shear forces which are obtained using dynamic analysis procedure. Major advantage of the proposed method is in the convenience in load combinations for design analysis.

구조물의 신뢰도를 평가하는 방법을 살펴보고 각각의 장,단점을 비교한다. 각 방법의 정확성을 평가하는 기준으로 Crude Monte Carlo(CMC)방법을 택하여, Importance Sampling(IS)방법, 그리고 Directional Sampling(DS)방법을 살펴 보고, 1차 근사방법은 현재 많이 사용되고 있는 Rackwitz-Fiessler(RF)방법, Chen과 Lind가 제안한 3-parameter방법(CL), Hohenbichler가 제안한 Rosenblatt 변환방법(RT)을, 그리고 2차 근사방법은 Breitung이 제안한 곡률적합 포물선 (Curvature Fitted Paraboloid,CFP)공식과 Kiureghian이 제안한 점적합 포물선(Point Fitted Paraboloid,PFP)공식, 그리고 Log-Likelihood function을 이용하여 원변수공간에서 파괴확률을 구하는 2차 근사공식(LLF)을 비교한다. 그리고 한계상태식이 불명확할 때 효율적으로 사용할 수 있는 반웅웅답법(Response surface method, RSM)을 살펴본다. 각 방법의 효율성 특히 적용 가능성을 예제를 통해 해석한 결과 추출법의 경우는 DS 방법이, 그리고 근사방법에서는 RSM 방법이 효율적임을 알 수 있었다.

The Neumann Expansion method has been used for evaluating the response variability of three dimensional truss structure resulting from the spatial variability of material properties with the aid of the finite element method, and in conjunction with the direct Monte Carlo simulation methods. The spatial variabilites are modeled as three-dimensional stochastic field. Yamazaki 〔1〕 has extended the Neumann Expansion method to the plane-strain problem to obtain the response variability of 2 dimensional stochastic systems. This paper presents the extension of the Neumann Expansion method to 3 dimensional stochastic systems. The results by the NEM are compared with those by the deterministic finite element analysis and by the direct Monte Carlo simulation method

Preflex composit girder is intended for a better use on both steel and concrete by introducting prestress into the lower flange concrete with preflection. In Korea, recently preflex bridges are widely used especially for urban construction but the design method depends on the conventional ASD(Allowable Stress Design). This paper suggests an optimization model for the design of preflex composite bridges based on LIFD(Load Resistance Factor Design). The optimization algorithm adopted for the NLP model proposed in the paper is the FTM(Flexible Tolerance Method) which is very efficient for the approximate continuous optimization. For the discrete optimum results, a pesudo discrete optimization is used for the economical round-up to the available dimensions. The economic effectiveness of optimum design based on the LRFD method is investigation by comparing the results with those of the ASD method. Based on applications to the actual design examples, it may be concluded that the optimization model suggested in the paper provides economical but reliable design. And the suggested in the paper provides economical but reliable design. And the computer code for the automatic optimum design of preflex bridges developed in the paper for a CAD system may be successfully used in practice.

The optimum weight design of structure is to determine the combination of structural members which minimize the weight of structures and satisfy design conditions as well. Since most of loads and design variables considered in structural design have uncertain natures, the reliability-based optimization techniques need to be developed. The aim of this study is to estabilish the general algorithm for the minimum weight design of transmission tower structure system with reliability constraints. The sequential linear programming method is used to solve non-linear minimization problems, which converts original non-linear programming problems to sequential linear programming problems. The optimal solutions are produced for various reliability levels such as reliability levels inherent in current standard transmission tower cross-section and optimal transmission tower cross-section obtained with constraints of current design criteria as well as selected target reliability index. The optimal transmission towers satisfying reliability constraints sustain consistent reliability levels on all members. Consequently, more balanced optimum designs are accomplished with less structural weight than traditional designs dealing with deterministic design criteria.

In this paper, TVLEM is selected for the shear wall model which was proposed by Kabeyasawa and the characteristics of spring models composing TVLEM was studied. In axial stiffness spring model, the horizontal displacements when Kabeyasawa model and simple axial stiffness hysteresis model were used, were closely similar. When the large shear-displacement was occured, stiffness degrading model was more adquate to the shear wall modelling than OOHM. Also for the purpose of modelling the horizontally continuous wall, the seperational method for TVLEM was used. The results of nonlinear analysis by this method were closely similar to experimental results .

In this paper a useful method on evaluating the joint stiffness of bolted memeber was introduced using optimization technique on the basis of Finite Element Method. A finite element model having one directional gap element at bo undary area was introduced to compensate the prying force in jointed members which might caused by geometrical configuration of members. Results showed a good aggrement with classical method in certain range and will be available to definine the design margine of pre-load design.

This paper presents a computer design program for In-Core Instrumentation(ICI) guide tube routing and locations on support system, and checking the interference between ICI guide tubes in the reactor coolant system of typical Pressurized Water Reactor. The program, ICITRIC, has been written in FORTRAN language which is available under UNIX environment. Results of this program are compared with those of the commercial code, PATRAN, and both results are almost same Also the results may provide input data for ICI system static and dynamic analysis performed by the commercial code, SUPER PIPE. This program can simulate ICI guide tube routing and locations on support system, and checking the interference between ICI guide tubes. Through a process of iteration, the designer can apply initial conditions, and modify the routing until satisfied with the overall system performance.

A non-linear mathematical model has been developed for the dynamic analysis of the reactor internals. The model includes a lumped mass and stiffness with non-linear members such as gap-spring. As hydrodynamic couplings have also been considered in the model, the effect of fluid/structure interaction between internals components due to their immersion in a confining fluid can be studied for the dynamic response analysis. The reactor internals responses for seismic and pipe break excitations have been calculated for the case of with-and without-hydrodynamic couplings.

주구조물의 여러층에 지지점을 가지는 부구조물의 응답스펙트럼 해석방법에 대하여 연구하였다. 본 연구에서는 지지점 입력간의 상관관계를 고려할 수 있으며 실무에서 부구조물의 내진설계에 쉽게 적용할 수 있는 다중 응답스펙트럼 해석방법을 제시하였다. 다중 응답스펙트럼과 지지점 입력간의 상관계수는 random vibration 이론을 이용하여 설계지반응웅답스펙트럼으로부터 직접 유도하였다. 예제해석 결과 본 연구에서 제안한 방법은 지지점 입력간의 상관관계를 고려하지 않는 통상의 다중 응답스펙트럼 해석방법보다 정확한 지진응답을 예측함을 알 수 있었다.

The seismic response of the reactor structures depends on the dynamic charact-eristics of the structures and the input earthquake loadings. The stuctural integ-rity of the reactor internal components can be verified by the dynamic response analyses to implement the effects of the design loadings like earthquakes. The sensitivity analyses of the dynamic characteristics for the analytical model of reactor structures considering the possible variations of the stiffnesses of the CSB upper flange and the snubber were performed to improve the dynamic characteri-stics of the structures against seismic loading. And to enhance the structural design margin of the reactor internal components the nonlinear time history analyses were attempted for the modified analytical model, and the results were compared between the reference model and the modified ones.

This paper presents the analysis briefs to evaluate the structural adequacy of the KMRR spent fuel storage racks which stack modules in three layers. The seismic analysis models are idealized to consider the overall dynamic motions such as rocking, sliding and liftoff in the event of an postulated earthquake. The displacement time histories of the floor obtained from the floor response spectra in three orthogonal directions are simultaneously applied to the nonlinear seismic model of the structure with gap and friction elements.

동적무한요소를 이용한 지반-구조물 상호작용에 대하여 연구하였다. 동적무한요소는 무한원방향으로 전파되어 나가는 여러종류의 지진파 성분을 동시에 모형화 할 수 있도록 개발된 축대칭요소로서, 구조물에서 멀리 떨어진 지반영역(외부영역)을 모형화 하는데 사용되었다. 반면, 구조물에 가까운 지반영역(내부영역)은 재래의 축대칭요소를 사용하여 모형화 하였다. 본 해석방법의 검증은 적충된 반무한 지반위에 놓여진 원형강판의 임피던스함수를 구하여, 이를 이론적 결과와 비교하는 방법으로 수행되었다. 또한, 지반에 일부가 묻힌 원통형구조물에 대하여 수행된 강제진동시험 결과와 실제 지진발생시 구조물의 거동기록을 같은 입력조건에 대하여 본 해법으로 구한 결과와도 비교하였다. 해석결과로 부터 본 해석방법이 구조물의 거동을 타당히 산정하여 줌을 알 수 있었다.

In the construction of underground structures, it is critical to accurately predict the ground deformations during excavation. In this paper, a finite element procedure for the computation of solid displacement and fluid pore pressure during incremental excavation is presented based on Biot's theory. The numerical formulation is done using the virtual work principle. The proposed procedure is applied to some example problems with different excavation rates and permeabilities.