The variable node plate bending element, ie, the element with one or two additional mid-side nodes is used in the analysis of mat foundation to generate the nearly ideal grid model in which more nodes are defined near the column location. The plate bending element used in this study is the one based on Mindlin/Reissner plate theory with substitute shear strain field and the nodal stresses of that element are obtained by the local smoothing technique. The interaction of the soil material with the mat foundation is modeled with Winkler springs connected to the nodal points in the mat model. The vertical stiffness of the soil material are represented in terms of a modulus of subgrade reaction and are computed in the same way as to the computation of consistent nodal force of uniform surface loading. Several mesh schemes were proposed and tested to find the most suitable scheme for mat foundation analysis.

구조물의 동적실험을 통하여 얻은 하중과 거동에 대한 시간기록을 분석하여, 구조계의 동 특성계수들을 추정하는 기법에 대하여 연구하였다. 실험과정 및 해석모형과정의 오차를 고려하기 위하여, 하중기록과 구조거동기록간의 관계를 추계론적 자동회기 및 이동평균모형(Stochastic Auto-Regressive and Moving-Average (ARMAX) Model)음 사용하여 모형화하였다. 미지의 ARMAX 계수행렬들은 순차적 예측오차기법을 사용하여 추정하였으며, 계수추정기법의 효율성을 증진시키기 위하여, Exponential Data Weighting, Global Data Weighting 및 Square Root Estimation 기법을 활용하였다. 다중거동측정계의 예제해석을 통하여 이의 효율성을 분석하였다.

The modal combination methods are studied for estimating the maximum structural responses in the seismic analysis by the response spectrum method. The most important problem in the modal combination is how to account for the correlation between the modal responses and to combine the high frequency modes (of which frequencies are greater than that at which the spectral acceleration approximately returns to the ZPA(zero period acceleration)). In this study, therefore, the widely known methods are investigated and compared among the numerous ones proposed up to now including those recommended in Regulatory Guide 1.92. The applicability of each method is investigated through example analyses also.

Modern tall buildings are subject to wind induced oscillations. Those oscillations can cause discomfort to the occupants. To control these motions, tuned mass dampers have been used. In this paper, component node synthesis, based on Lagrange multipliers formulation. is applied to the along-wind motion of tall buildings with multiple tuned mass dampers. Spectral densities of accelerations of top floor are compared by changing the numbers and locations of tuned mass dampers. It is found that multiple tuned mass dampers can be more effective than single tuned mass damper in reducing the acceleration response.

Since many design problems in the railroad, aerospace and machine structures involve considerations of the effect of cyclic loading, manufacturing and quality control processes must fully account for fatigue of critical components. Due to the sensitivity of the Paris law, it is very important to calculate the ΔK numerically to minimize the error of predicted fatigue life in cycles. It is shown that the p-version of FEM based on LEFM analysis is far better suited for computing the stress intensity factors than the conventional h-version. To demonstrate the proficiency of the proposed scheme, the welded T-joint with crack problem of box car body bolster assembly and a crack problem emanating Iron a circular hole in finite strip have been solved.

This paper proposes a method of h-type adaptive mesh generation for the finite element analysis of two dimensional elasticity problem. The error energy norm of a posteriori error estimation is difined based on the complementary energy of each element. Computer codes are developed and some examples are investigated. It is shown that the approach to the optimized mesh in this paper is effective and useful.

해양 가이드 타워를 대상으로 하여, 지진하중에 대한 심해응구조물의 비정상거동해법에 대하여 연구하였다. 지반운동의 비정상특성은 정상과정성분에 시간포락함수가 곱해진 형태로 모형화하였으며, 구조물의 비정상거동은 시간종속분산함수로 구하였다. 지반가속도에 대한 자기상관함수를 복소지수함수의 형태로 이상화함으로써, 구조물 거동의 시간종속함수가 해석적인 방법으로 쉽게 구할 수 있는 기법을 개발하였다. 지진의 발생시간 동안 예상되는 최대거동을 구하였으며. 이를 구조물 거동을 정상확률과정으로 가정하여 산정한 결과와 비교 분석하였다.

The primary objective of this study is the development of second moment methods for the efficient reliability evaluations of structural systems. Two methods are presented. One is the improved first order reliability method (IFORM), and the other is the modified probabilistic network evaluation technique (MPNET). For the purpose of verifying the proposed methods, example analyses are carried out on several cases with two failure modes, a plane frame structure involving three failure modes and simplified parallel member models for fatigue reliability evaluations of offshore structures. Numerical results indicate that the effectiveness of the proposed methods over the conventional ones (i.e., the FORM and the PNET) increases very significantly as the number of failure modes of the system increases.

It is usual that underground structures are constructed within multi-layered medium. In this paper, an efficient numerical model ling of multi-layered structural systems is studied using coupled analysis of finite elements and boundary elements. The finite elements are applied to the area in which the material nonlinearity is dominated, and the boundary elements are applied to the far field area where the nonlinearity is relatively weak. In the boundary element model 1 ins of the multi-layered medium, fundamental solutions are restricted. Thus, methods which can utilize existing Kelvin and Melan solution are sought for the interior multi-layered domain problem and semi infinite domain problem. Interior domain problem which has piecewise homogeneous layers is analyzed using boundary elements with Kelvin solution; by discretizing each homogeneous subregion and applying compatibility and equilibrium conditions between interfaces. Semi-infinite domain problem is analyzed using boundary elements with Melan solution, by superposing unit stiffness matrices which are obtained for each layer by enemy method. Each methodology is verified by comparing its results which the results from the finite element analysis and it is concluded that coupled analysis using boundary elements and finite elements can be reasonable and efficient if the superposition technique is applied for the multi-layered semi-infinite domain problems.

This study deals with the finite element analysis of the monotonic behavior of reinforced concrete beams and beam-column joint subassemblages. It is assumed that the behavior of these members can be discribed by a plane stress field. Concrete and reinforcing steel are represented by separate material models which are combined together with a model of the interaction between reinforcing bar and concrete through bond-slip to discribe the behavior of the composite reinforced concrete material. To discribe the concrete behavior, a nonlinear orthotropic model is adopted and the crack is discribed by a system of orthogonal cracks, which are rotating as the principal strain directions are changed. A smeared finite element model based on the fracture mechanics principles are used to overcome the numerical defect according to the finite element mesh size. Finally, correlation studies between analytical and experimental results and several parameter studies are conducted with the objective to estabilish the validity of the proposed model and identify the significance of various effects on the local and global response of reinforced concrete members.

A stochastic simulated anneal ins (SSA) is a recent approach to the solution of problems characterized by large number of interacting degrees of freedom. SSA simulates the degrees of freedom in a problem in a such a way that they are a collection of atoms slowly being coolded into a ground state which would correspond to the stationary point of the problem. In this paper, for a randomly disturbed current design, SSA optimization technique is used, which establishes a probabilistic criterion for acceptance or rejection of current design and iteratively improves it to arrive at a stationary Point at which critical temperature is reached. Simple truss optimization problem which consider as their constraints only the tensile and compressive yielding strength of the members are tested using SSA. Satisfactory results are obtained and some discussions are given for the behavior of SSA on the tested truss structures.

An integrated design system has as its aim the incoporation of all the design processes, such as, planning, preliminary design, analysis, detailed design (mamber design), evaluation, and drafting into an unified software system. Successful implementation such a system could lead to major improvements in efficiency by eliminating duplication of data and efforts. reducing errors, saving design time, providing management support, and so on. This study presents a methodology for an computer-integrated design system for building structures, synthesizing algorithmic procedures and knowledge based expert systems on the network database. Network database, which was designed to store all information systematically during the design processes, provides centeral communication area between algorithms and expert systems. The conventional procedural codes automate the routine design phases such as structural analysis, whereas knowledge-based expert systems support designer's decisions at the creative design phases such as preliminary design etc. The user interface with interactive and batch modes controls the design phases and manages design information and activates the algorithms and the expert systems. The concept presented in this paper will contribute to the formulation of automated design systems for building structures.

In general, the strength and stiffness of laminated composite cylinderical shells are very sensitive to the variation of slenderness parameters, some coupling-stiffness parameters, lamination angles, stacking sequence and number of layers. In the paper, the effects of these factors on the strength and buckling reliabilities of GFRP laminated cyclinderical shells are investigated based on the proposed strength and buckling limit state models. It may be concluded that the applicable ranges of the slenderness limits of the strength and buckling failure criteria for laminated composite cylinderical shells should be indentified and incorporated into the design formula with appropriate safety factors which provide uniform consistent reliability for balanced design in practice.

구조물의 비탄성 지진응답을 예측하기 위하여 수행되는 진동대 실험(Shaking Table Test)과 준정적 실험(Quasic-Static Test)의 각 장점을 조합한 유사동적 실험(Pseudodynamic Test)은 실물 크기 구조물의 비탄성 거동온 파악하는 데 널리 사용되고 있다. 이러한 유사동적 실험에서는 구조물에 변위이력의 정확한 가력 및 측정이 가장 중요하다. 측정된 변위와 계산된 변위의 차를 조절오차(Control Error)라고 하며, 임의의 단계에서 측정된 변위를 조정하므로서 그 다음 단계의 조절오차 및 측정오차(Measurement Error)를 감소시킬 수 있다. 따라서 개선된 유사동적 실험의 알고리즘을 얻을 수 있다.

The Pseudodynamic test is a new experimental technique for simulating the earthquake response of structures or structural components in the time domain. It is especially efficient for testing structures that are too large, heavy or strong to be tested on a shaking table. But the obtained responses in the Pseudodynamic test are distorted by the experimental errors inevitably during control and measurement procedures. The studies are to investigate the effects of the experimental errors on the Pseudodynamic responses and apply a correction method to the Pseudodynamic testing algorithm. It is shown that the corrected responses using the Equivalent Energy Compensation Method are in a good correlation with the theoretical ones. Thus, the corrected Pseudodynamic responses could be reliable for evaluating the seismic performance of structural systems.

This study deals with the effect of a series of moving trucks on the Dynamic Load Factor (DLF). The DLF is calculated by investigating the load effect of moving trucks. Therefore, analytical models for frocks, bridge, and road profiles were developed and dynamic structural analysis computer program were developed. Then the DLFs are calculated as a ratio of maximum dynamic load effect and maximum static load effect. Trucks used in this study are 5 axle semi tractor-trailer with the weight of 36 and 54 ton. Simply supported prestressed concrete box girder bridges with 20 and 40m span length are selected. From the results of the DLF for various headway distances, they show a very scattered and relatively high values of the DLF in case of a 20m span length bridge. For a 40m span length bridge, the results show less scattered and small increase of the DLF compared to a 20m span length bridge.

In order to design and construct a safe and economic underground structure, it is essential to understand the structural behavior of underground openings considering the effect of the sequential excavation. Therefore, this paper includes the study of initial stress distribution before excavation and stress redistribution due to the sequential excavation. And discussion on numerical simulation techniques for the sequential excavation is also included. Then, the underground structure is analyzed using the finite element and distinct element methods of analysis considering the effect of the sequential excavation. Based on the results of the analysis, the followings are discussed: shape of the openings, effect and timing of structural reinforcements. methods and sequence of excavation.

The ground deformation due to the tunnel excavation is dependent on various factors such as ground condition, geometry of the tunnel, excavation method, installation of support members, construction condition of each excavation stage, etc. And the distance from the facing effects significantly the stress conditions of the supported and unsupported ground due to the 3-dimensional structural nature of the excavated tunnel. The concept of ground characteristic line has been applied to properly consider the loading condition given by staged tunnel excavation so that the imaginary supporting pressure is applied against the surface of excavated ground. Discussions on the results of the performed finite element analysis were mainly made with respect to the ground settlement, tunnel displacement, earth pressure, stress mobilized in supporting members.

The structural soundness of bridges is mainly damaged by overloaded heavy vehicles. The increasing volumes of overloaded heavy vehicles has been indicated as serious state. As results several countries have revised their bridge load codes. However, because of variety of truck types and their weights it is difficult to develop rational standard truck loads. In addition the common practice that only one design configuration of standard truck is adopted to design variety of bridges causes further difficulties. The objective of the study is to investigate the statistical characteristics of vehicle loadings based on survey data col looted, in which some major factors, such as vehicle configurations, vehicle freights, traffic modes, etc. are incorporated.

This study introduces simple derivation of optimum load factors based on both cornell's MFOSM (Mean First Order End Moment) methods and Lind - Hasofers AFOSM (Advanced First Order 2nd Moment) methods and demonstrates the relationship between the optimum reliability, the load factors, the probability distributions selected to model the load, and a measure of relative failure cost. Although some of the cost parameters cannot be evaluated accurately and the upper tail characteristics of the distributions of the random loads remain uncertainty, this optimum reliability formulation provides insight on which Parameters are most significant in selecting appropriate load criteria for structure design.