In this study, it should be mentioned that Lipid-LCG can be prepared with the main compound of hydrogenated lecithin in oil-in water emulsion. The results of its physical property and stability are as follows. First, the best suitable compositions of Lipid-LCG are made from 4.0wt% of the hydrogenated lecithin, 4.0wt% of cetostearyl alcohol as emulsifier and gelling agent, 3.0wt% of butylene glycol and 2.0wt% glycerin as moisturizers, 3.0wt% of cyclomethicone, 3.0wt% of isononyl-isononanoate, 3.0wt% of capric/caprylic triglycerides, 3.0wt% of macadamia oil as emollients. Second, As the optimum conditions to form Lipid-LCG, which figured out 6.0 ${\pm}$ 1.0 for pH level, 32kg/mm, min for hardness to make a .essence to be formed the ternary phase of liquid crystal(multi-lamellar type). Third, as the analytical result of this system, it obtained that particle size is $1{\sim}8{\mu}m$ level, and is certified with it at 400 and 1,000 magnifications by microscope. The stability of Lipid-LCG is very stable on condition of a low temperature ($4^{\circ}C$), a room temperature ($25^{\circ}C$) and a high temperature ($40^{\circ}C$), which is not to be split in for a long time(for 3-month). We produced our own moisturizing essence, which has a good affinity to skin by means of this system.

It is a great role that the character of man or woman could be distinguished by hair on the aspect of ornament. Hair will be support of beautifulness of human being in various permanent wave by many kinds of its drugs. Hair is based upon the skin which enroll the body of high living animals and have multiple membrane structure. This study used rat and the effects of commercial permanent wave products to skin which are composed with thioglycolic acid and bases. Results are as follows. Permanent wave penetrated to 4 hours later with steady state in skins and was not significant changeable after 20hr later. In case of neutralizer with thioglycolic acid lag time and permeability coefficient in healthy skin is 3.38hr and $0.094^{\mu}g/cm^{2}$ ${\cdot}$ hr, it old skin is 3.48hr and 0.129$^{\mu}g/cm^{2}$ ${\cdot}$ hr, and it wounded skin is 4.72hr and $0.158^{\mu}g/cm^{2}$ ${\cdot}$ hr. In conclusion, lag time and permeability coefficient in old skin and wounded skin are faster than healthy skin. In vivo which was studied by general time and method of permanent wave. We notified that fine rinkle and rash of skin were changeable in the case of treating with permanent wave drugs than normal skin. We can see even rash and eruption by the naked eye.

Two PU flame-retardant coatings, 2,3-DBPO/N-l00 (DBPON) and 2,3-DBPO/IL (DBPOI), were prepared by curing 2,3-dibromo modified polyester (2,3-DBPO) with isocyanate curing agent Desmodur N-l00 (or Desmodur IL) at room temperature. The physical properties and flame-retardancy of the two coatings were tested and compared. As a result, the pot-life, yellowness index, lightness index difference, $60^{\circ}$ specular gloss, cross-hatch adhesion, viscosity, and accelerated weathering resistance of DBPON were better than those of DBPOI; the fineness of grind of the two coatings were the same; and the drying time, hardness, and abrasion resistance of DBPOI were better than those of DBPON. The flame retardancy of the flame-retardant coatings increased with the content of the flame retarding component, 2,3-dibromopropanoic acid (2,3-DBP); and the LOI values of the two coatings were in a range of $27{\sim}29%$ when the content of 2,3-DBP was 30wt%.

Copolymerization of ${\alpha}$-Methylstyrene(AMS) with Acrylonitrile(AN) was carried out with benzoylperoxide(BPO) as an initiator in toluene at $80^{\circ}C$ in a continuous stirred tank reactor. Reaction volume and residence time were 0.6 liters and 3 hours, respectively. The monomer reactivity ratios, $r_{AMS}$ and $r_{AN}$ determined by both the Kele$T{\"{u}}d\"{o}s$ method and the Fineman-Ross method were $r_{AMS}$=0.16(0.14), $r_{AN}$=0.04(0.06). The cross-termination factor ${\Phi}$ of the copolymer over the entire AMS composition ranged from 0.75 to 0.92. The ${\Phi}$ factors of poly(AMS-co-AN) were increased with increasing AMS content. The simulated conversions and copolymerization rates were compared with the experimental results. It was observed that the average time to reach dynamic steady-state was three times the residence time.

We carried out this subject to observe photoisomerization using 1,2-dioleoyl-sn- glycero-3-phosphocholine(DOPC) mixed with fatty acid containing azobenzene group which has reversible to cis-trans by light irradiation. Spreading solutions for the LB films were prepared in chloroform($5.0{\times}10^{-5}$mol/L).We investigated the photoisomerization and property of the organic ultra thin film of fatty acid containing azobenzene was prepared on the hydrophilic ITO(idium tin oxide) glass plate by LB method. As a result, the absorption spectra of 8A5H and DOPC of mixture LB films was induced to photoisomerization by alternating irradiation of ultraviolet and visible light, because the condensation of pure azobenzene monolayers was loosened by the introduction of phospholipid into the monolayers, and the molecular high aggregation in pure azobenzene monolayers is also weakened by the introduction of phospholipid. We found that it was reversibly induced to cis-trans photoisomerization in several solvents and mixture LB films.

We carried out this experiment to observe electrochemical properties for LB films of phospholipid(Dilauroyl-L-${\alpha}$-Phosphayidylcholine) and 4-octyl-4'-(5-carboxypentamethylene-oxy)azobenzene mixture by the cyclic voltammetry. LB films of 8A5H and 8A5H-DLPC(1:1, 2:1) were deposited by using the Langmuir-Blodgett method on the ITO glass. We determined electrochemical measurement by using cyclic voltammetry with a three-electrode system, An Ag/AgCl reference elect rode, a platinum wire counter electrode and LB film-coated ITO working electrode measured in 0.1, 0.5, and 1.0 mol/L $NaClO_{4}$ solution. A measuring range was reduced from initial potential to -1350 mV, continuously oxidized to 1650 mV and measured to the initial point. The scan rate were 50, 100, 150 and 200 mV/s. As a result, LB films of 8A5H 8A5H-DLPC appeared irreversible process caused by only the oxidation current from the cyclic voltammogram.

Microemulsion is stable to aggregation, sedimentation, fusion and has $3nm{\sim}200nm$ of particle size which is transparent and semitransparent. The isoflavone as a derivatives of Flavone is colorless crystalline compounds. It has similar basic structure to steroid materials which is hormone that acts to skin physiological phenomenon. On this study, we tried to search and demonstrate system content rate of dermal translocation system for cosmetics using O/W type microemulsion containing isoflavone. We manufactured O/W microemulsions by phase inversion emulsification method. It's was found that POE(20) monostearate with HLB value 14 caused microemulsion to be formed, which had $4nm{\sim}18nm$ of average diameter and $3nm{\sim}33nm$ of particle size distribution. Apparent viscosities of the microemulsions have increased in proportion to add surfactant dose.

Natto is a Japanese traditional food made from whole soybeans by the fermentation of Bacillus natto. The purpose of this study was to investigate the effect of Natto mucilage on lipid metabolism in rats. The levels of total cholesterol, LDL-cholesterol and triglyceride in serum of rats fed Natto mucilage diets were lower than those in control rats, but serum HDL-cholesterol and phospholipid were higher than those in control rats. The results indicate that Natto mucilage may have more beneficial roles in lipid metablism because it decreased serum cholesterol and increased bilirubin excretion.

We have seen the effects of buffer layer in organic light-emitting diodes(OLEDs) using poly(N-vinylcarbazole)(PVK) depending on a concentration of PVK. Polymer PVK buffer layer was made using spin casting technique. Two device structures were fabricated; one is ITO/TPD/$Alq_{3}$/Al as a reference, and the other is ITO/PVK/TPD/$Alq_{3}$/Al to see the effects of buffer layer in organic light-emitting diodes. Current-voltage-luminance characteristics and an external quantum efficiency were measured with a variation of spin-casting rpm speeds and PVK concentration. We have obtained an improvement of external quantum efficiency by a factor of four when the PVK concentration is 0.1wt% is used. The improvement of efficiency is expected due to a function of hole-blocking of PVK in OLEDs.