• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.3
• /
• pp.627-631
• /
• 2009

This paper presents a novel current steering cell matrix DAC(digital-to-analog converter) architecture to reduce decoder area. The current cell matrix of a existing architecture is selected by columns and lows thermometer code decoder of input bits. But The current cell matrix of a proposal architecture is divided 2n by the thermometer code decoder of upper input bits and are selected by the thermometer code decoder of middle and lower input bits. Because of this configuration, decoder numbers have increased. But the gate number that composed of decoder has decreased. In case of the designed 8 bit current steering cell matrix DAC, the gate number of decoder has decreased by about 55% in comparison with a existing architecture.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.2
• /
• pp.44-48
• /
• 2009

A simulation study of a 10-bit two-stage DAC was done by using a conventional current switch cell. The DAC adopts the segmented architecture in order to reduce the circuit complexity and the die area. The 10-bit CMOS DAC was designed in 2 blocks, a unary cell matrix for 6 MSBs and a binary weighted array for 4 LSBs, for fabrication in a 0.35-${\mu}m$ CMOS process. To cancel the accumulation of errors in each current cell, a symmetrical switching sequence is applied in the unary cell matrix for 6 MSBs. To ensure high-speed operation, a decoding circuit with one stage latch and a cascode current source were developed. Simulations show that the maximum power consumption of the 10-bit DAC is 74 mW with a sampling frequency of 100 MHz.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.3
• /
• pp.270-277
• /
• 2012

This paper presents a new DAC design strategy to achieve a wideband dynamic linearity by increasing the bandwidth of the output impedance. In order to reduce the dominant parasitic capacitance of the conventional matrix structure, all the cells associated with a unit current source and its control are stacked in a single column very closely (stacked unit cell structure). To further reduce the parasitic capacitance, the size of the unit current source is considerably reduced at the sacrifice of matching yield. The degraded matching of the current sources is compensated for by a self-calibration. A prototype 6-bit 3.3-GS/s current-steering full binary DAC was fabricated in a 1P9M 90 nm CMOS process. The DAC shows an SFDR of 36.4 dB at 3.3 GS/s Nyquist input signal. The active area of the DAC occupies only $0.0546mm^2$ (0.21 mm ${\times}$ 0.26 mm).

• ETRI Journal
• /
• v.35 no.1
• /
• pp.158-161
• /
• 2013

This letter proposes a low-power current-steering digital-to-analog converter (DAC). The proposed DAC reduces the clock power by cutting the clock signal to the current-source cells in which the data will not be changed. The 10-bit DAC is implemented using a $0.13-{\mu}m$ CMOS process with $V_{DD}$=1.2 V. Its area is $0.21\;mm^2$. It consumes 4.46 mW at a 1-MHz signal frequency and 200-MHz sampling rate. The clock power is reduced to 30.9% and 36.2% of a conventional DAC at 1.25-MHz and 10-MHz signal frequencies, respectively. The measured spurious free dynamic ranges are 72.8 dB and 56.1 dB at 1-MHz and 50-MHz signal frequencies, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.10
• /
• pp.39-45
• /
• 2011

This paper proposes a low power current-steering 10-bit DAC selecting clock enable signal. The proposed DAC reduces the clock power by cutting the clock signal to the current-source cells in wihich the data will not be changed. The proposed DAC was implemented using a 0.13${\mu}m$ CMOS process with $V_{DD}=1.2V$. Its core area is 0.21$mm^2$. It consumes 4.46mW at 1MHz signal frequency and 200MHz sampling rate. The clock power is reduced to 30.9% and 36.2% of a conventional DAC at 1.25MHz and 10MHz signal frequencies, respectively. The measured SFDRs are 72.8dB and 56.1dB at 1MHz and 50MHz signal frequencies, respectively.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.619-620
• /
• 2006

This paper presents a design of a 6-bit 2.704Gsamples/s D/A converter (DAC) for DS-CDMA UWB transceivers. The proposed DAC was designed with a current steering segmented 4+2 architecture for high frequency sampling rate. For low glitches, optimized deglitch circuit is adopted for the selection of current sources. The measured integral nonlinearity (INL) is -0.081 LSB and the measured differential nonlinearity (DNL) is -0.065 LSB. The DAC implemented in a 0.13um CMOS technology shows s spurious free dynamic range (SFDR) of 50dB from dc to Nyquist frequency. The prototype DAC consumes 28mW for a Nyquist sinusoidal output signal at a 2.704Gsamples/s. The chip has an active area of $0.76mm^2$.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.13-18
• /
• 2013

In this paper design a 8 bit Current Steering D/A Converter for stimulating neuron signal. Proposed circuit in paper shows the conversion rate of 10KS/s and the power supply of 3.3V with 0.35um Magna chip CMOS process using full custom layout design. It employes segmented structure which consists of 3bit thermometer decoders and 5bit binary decoder for decreasing glitch noise and increasing resolution. So glitch energy is down by $10nV{\bullet}sec$ rather than binary weighted type DAC. And it makes use of low power current stimulator because of low LSB current. And it can make biphasic signal by connecting with Micro Controller Unit which controls period and amplitude of signal. As result of measurement INL is +0.56/-0.38 LSB and DNL is +0.3/-0.4 LSB. It shows great linearity. Power dissipation is 6mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.685-691
• /
• 2003

This work describes a 3 V 12b 100 MS/s CMOS digital-to-analog converter (DAC) for high-speed communication system applications. The proposed DAC is composed of a unit current-cell matrix for 8 MSBs and a binary-weighted array for 4 LSBs, considering linearity, power consumption, chip area, and glitch energy. The low-glitch switch driving circuit is employed to improve the linearity and the dynamic performance. Current sources of the DAC are laid out separately from the current-cell switch matrix core. The prototype DAC is implemented in a 0.35 urn n-well single-poly quad-metal CMOS technology. The measured DNL and INL of the prototype DAC are within $\pm$0.75 LSB and $\pm$1.73 LSB, respectively, and the spurious-free dynamic range (SFDR) is 64 dB at 100 MS/s with a 10 MHz input sinewave. The DAC dissipates 91 mW at 3 V and occupies the active die area of 2.2 mm ${\times}$ 2.0 mm.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.4
• /
• pp.211-216
• /
• 2003

This work describes a 3 V 12b 100 MS/s CMOS digital-to-analog converter (DAC) for high-speed communication system applications. The proposed DAC is composed of a unit current-cell matrix for 8 MSBs and a binary-weighted array for 4 LSBs, trading-off linearity, power consumption, chip area, and glitch energy with this process. The low-glitch switch driving circuits are employed to improve linearity and dynamic performance. Current sources of the DAC are laid out separately from the current-cell switch matrix core block to reduce transient noise coupling. The prototype DAC is implemented in a 0.35 um n-well single-poly quad-metal CMOS technology and the measured DNL and INL are within ${\pm}0.75$ LSB and ${\pm}1.73$ LSB at 12b, respectively. The spurious-free dynamic range (SFDR) is 64 dB at 100 MS/s with a 10 MHz input sinewave. The DAC dissipates 91 mW at 3 V and occupies the active die area of $2.2{\;}mm{\;}{\times}{\;}2.0{\;}mm$

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.331-337
• /
• 2017

In this paper, we present the design of a 20MHz bandwidth 3rd-order continuous-time low-pass sigma-delta modulator with low-noise and low-power consumption. The bandwidth of the system is sufficient to accommodate LTE and other wireless network standards. The 3rd-order low-pass filter with feed-forward architecture achieves the low-power consumption as well as the low complexity. The system uses 3bit flash quantizer to provide fast data conversion. The current-steering DAC achieves low-power and improved sensitivity without additional circuitries. Cross-coupled transistors are adopted to reduce the current glitches. The proposed system achieves a peak SNDR of 65.9dB with 20MHz bandwidth and power consumption of 32.65mW. The in-band IM3 is simulated to be 69dBc with 600mVp-p two tone input tones. The circuit is designed in a 0.18-um CMOS technology and is driven by 500MHz sampling rate signal.