• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.4
• /
• pp.275-279
• /
• 2004

A new burst mode clock and data recovery circuit is realized that improves the previousldy-known gated-oscilletor technique with half rate clock recovery, The circuit was fabricated with 0.25um CMOS technology, and its functions were confirmed up to 1 Gbps.

• Journal of IKEEE
• /
• v.17 no.4
• /
• pp.544-549
• /
• 2013

This paper describes a modified binary phase detector (Bang-Bang phase detector - BBPD) for jitter reduction in clock and data recovery (CDR) circuits. The proposed PD reduces ripples in the VCO control voltage resulting in reduced jitter for CDR circuits. A 2.5 Gbps CDR circuit with a proposed BBPD has been designed and verified using Dongbu $0.13{\mu}m$ CMOS technology. Simulation shows the CDR with proposed PD recovers data with peak-to-peak jitter of 10.96ps, rms jitter of 0.86ps, and consumes 16.9mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.28-33
• /
• 2006

An integrated 3.125Gbps clock and data recovery (CDR) circuit is presented. The circuit does not need a reference clock. It has a phase and frequency detector (PFD), which incorporates a bang-bang type 4X oversampling PD and a rotational frequency detector (FD). It also has a ring oscillator type VCO with four delay stages and three zero-offset charge pumps. With a proposed PD and m, the tracking range of 24% can be achieved. Experimental results show that the circuit is capable of recovering clock and data at rates of 3.125Gbps with 0.18 um CMOS technology. The measured recovered clock jitter (p-p) is about 14ps. The CDR has 1.8volt single power supply. The power dissipation is about 140mW.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.87-95
• /
• 2013

In this paper, 2.5 Gb/s burst-mode clock and data recovery(CDR) is presented. Digital frequency calibration scheme is adopted to eliminate mismatch between the input data rate and the output frequency of the gated voltage controlled oscillator(GVCO) in the clock recovery circuitry. A jitter rejection scheme is also used to reduce jitter caused by input data. The proposed burst-mode CDR is designed using 0.11 ${\mu}m$ CMOS technology. Post-layout simulations show that peak-to-peak jitter of the recovered data is 14 ps with 0.1 UI input referred jitter, and maximum tolerance of consecutive identical digit(CID) is 2976 bits without input data jitter. The active area occupies 0.125 $mm^2$ without loop filter and the total power consumption is 94.5 mW.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.77-86
• /
• 2016

This paper describes a dual-mode reference-less CDR(Clock Data Recovery) operating at full / half-rate and its operation algorithm. Proposed reference-less CDR consists of a frequency detector, a phase detector, a charge pump, a loop filter, a voltage controlled oscillator, and a digital block. The frequency and phase detectors operate at both full / half-rate for dual-mode operation and especially the frequency detector is capable of detecting the difference between data rate and clock frequency in the dead zone of general frequency detectors. Dual-mode reference-less CDR with the proposed algorithm can recover the data and clock within 1.2-1.3 us and operates reliably at both full-rate (2.7 Gb/s) and half-rate (5.4 Gb/s) with 0.5-UI input jitter.

• The Journal of the Korea Contents Association
• /
• v.10 no.2
• /
• pp.72-80
• /
• 2010

The 1Gbps clock and data recovery (CDR) circuit using the proposed multi-point phase detector (PD) is presented. The proposed phase detector generates up/down signals comparing 3-point that is data transition point and clock rising/falling edge. The conventional PD uses the pulse width modulation (PWM) that controls the voltage controlled oscillator (VCO) using the width of a pulse period's multiple. However, the proposed PD uses the pulse number modulation (PNM) that regulates the VCO with the number of half clock cycle pulse. Therefore the proposed PD can controls VCO preciously and reduces the jitter. The CDR circuit is tested using 1Gbps $2^{31}-1$ pseudo random bit sequence (PRBS) input data. The designed CDR circuit shows that is capable of recovering clock and data at rates of 1Gbps. The recovered clock jitter is 7.36ps at 1GHz and the total power consumption is about 12mW. The proposed circuit is implemented using a 0.18um CMOS process under 1.8V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.2
• /
• pp.130-134
• /
• 2008

This paper presents a clock and data recovery(CDR) using a quarter-rate technique. The proposed CDR helps reduce the VCO frequency and is thus advantageous for high speed application. It can achieve a low jitter operation and extend the pull-in range without a reference clock. The CDR consists of a quarter-rate bang-bang type phase detector(PD) quarter-rate frequency detector(QRFD), two charge pumps circuits(CPs), low pass filter(LPF) and a ring voltage controlled oscillator(VCO). The Proposed CDR has been fabricated in a standard $0.18{\mu}m$ 1P6M CMOS technology. It occupies an active area $1{\times}1mm^2$ and consumes 98 mW from a single 1.8 V supply.

• ETRI Journal
• /
• v.44 no.5
• /
• pp.859-874
• /
• 2022

This paper presents a low-power and lightweight human body communication (HBC) receiver with an embedded dummy electrode for improved signal acquisition. The clock data recovery (CDR) circuit in the receiver operates with a low supply voltage and utilizes a clock phase inversion scheme. The receiver is equipped with a main electrode and dummy electrode that strengthen the capacitive-coupled signal at the receiver frontend. The receiver CDR circuit exploits a clock inversion scheme to allow 0.9-V operation while achieving a shorter lock time than at 3.3-V operation. In experiments, a receiver chip fabricated using 130-nm complementary metal-oxide-semiconductor technology was demonstrated to successfully receive the transmitted signal when the transmitter and receiver are placed separately on each hand of the user while consuming only 4.98 mW at a 0.9-V supply voltage.

• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.4
• /
• pp.39-45
• /
• 2015

In this paper, variable rate CDR(Clock and Data Recovery) circuit adopting blind oversampling architecture is presented. The clock recovery circuit is implemented by using wide range voltage controlled oscillator and band selection method and the data recovery circuit is designed to digital circuit used majority voting method in order to low power and small area. The designed low power variable clock and data recovery is implemented by wide range voltage controlled oscillator and digital data recovery circuit. The designed variable rate CDR is operated from 10 bps to 2 Mbps. The total power consumption is about 4.4mW at 1MHz clock. The supply voltage is 1.2V. The designed die area is $120{\mu}m{\times}75{\mu}m$ and this circuit is fabricated in $0.13{\mu}m$ CMOS process.

• Journal of IKEEE
• /
• v.13 no.2
• /
• pp.118-125
• /
• 2009

With recent advancement of high-speed, multi-gigabit data transmission capabilities, transmitters usually send data without clock signals for reduction of hardware complexity, power consumption, and cost. Therefore clock and data recovery circuits(CDR) become important to recover the clock and data signals and have been widely studied. This paper presents the design of 10Gbps CDR in 0.18$\mu$m CMOS process. A quarter-rate bang-bang phase detector is designed to reduce the power and circuit complexity, and a 4-stage LC-type VCO is used to improve the jitter characteristics. Simulation results show that the designed CDR consumes 80mW from a 1.8V supply, and exhibits a peak-to-peak jitter of 2.2ps in the recovered clock. The chip layout area excluding pads is 1.26mm$\times$1.05mm.