• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.43-48
• /
• 2008

This paper presents a design of 8B/10B encoder by the coding table reduction. The proposed encoder has reduced coding table modified disparity control block. Logic simulation and synthesis have been done for the proposed design. After synthesized using Magna CMOS $0.18{\mu}m$ process, the proposed design achieved the operating frequency of 343MHz and chip area of $1886{\mu}m^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.60-68
• /
• 2007

A technique is presented to extract differential second harmonic output from common source nodes of a cross-coupled P-& N-FET oscillator. Provided the impedances at the common source nodes are optimized and the fundamental swing at the VCO core stays in a proper mode, it is found that the amplitude and phase errors can be kept within $0{\sim}1.6dB$ and $+2.2^{\circ}{\sim}-5.6^{\circ}$, respectively, over all process/temperature/voltage corners. Moreover, an impedance-tuning circuit is proposed to compensate any unexpectedly high errors on the differential signal output. A Prototype 5-GHz VCO with a 2.5-Hz LC resonator is implemented in $0.18-{\mu}m$ CMOS. The error signal between the differential outputs has been measured to be as low as -70 dBm with the aid of the tuning circuit. It implies the push-push outputs are satisfactorily differential with the amplitude and phase errors well less than 0.34 dB and $1^{\circ}$, respectively.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.4
• /
• pp.26-33
• /
• 2010

This paper presents a multi-channel capacitive touch sensing unit for SoC applications. This unit includes a simple common processing unit and switch array to detect the touch sensing input by capacitive-time(C-T) conversion method. This touch sensor ASIC is designed based on the Capacitive-Time(C-T) conversion method to have advantages of small current and chip area, and the minimum resolution of the unit is 41 fF per count with the built-in sensing oscillator, LDO regulator and $I^2C$ for no additional external components. This unit is implemented in 0.18 um CMOS process with dual supply voltage of 1.8 V and 3.3 V. The total power consumption of the unit is 60 uA and the area is 0.26 $mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.1
• /
• pp.28-36
• /
• 2008

This paper discusses theimplementation of the low-voltage, low-power, third-order, 1-bit switched capacitor delta-sigma modulator of the implantable cardiac pacemaker. The distributed, feed-forward structure and bulk-driven OTA were used in order to achieve an efficient operation under a supply voltage of 1V or lower. The designed modulator has a dynamic range of 49dB at 0.9V supply voltage and consumes 816nW of power. Such a significant reduction in power consumption allows diverse applications, not only in pacemakers, but also in implantable biomedical devices that operate with limited battery power. The core chip size of the modulator is $1000{\mu}m*500{\mu}m$ manufactured, with the $0.18{\mu}m$ CMOS standard process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.405-410
• /
• 2012

This paper presents an inductorless 8-Gb/s adaptive passive equalizer with low-power consumption and small chip area. The equalizer has a tunable RC filter which provides high-frequency gain boosting and a limiting amplifier that restores the signal level from the filter output. It also includes a feedback loop which automatically adjusts the filter gain for the optimal frequency response. The equalizer fabricated in $0.18-{\mu}m$ CMOS technology can successfully equalize 8-Gb/s data transmitted through up to 50-cm FR4 PCB channels. It consumes 6.75 mW from 1.8-V supply voltage and occupies $0.021mm^2$ of chip area.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.9
• /
• pp.31-39
• /
• 2011

In this paper, we propose a signal readout system with small area and low power consumption for CNT sensor arrays. The proposed system consists of signal readout circuitry, a digital controller, and UART I/O. The key components of the signal readout circuitry are 64 transimpedance amplifiers (TIA) and SAR-ADC with 11-bit resolution. The TIA adopts an active input current mirror (AICM) for voltage biasing and current amplification of a sensor. The proposed architecture can reduce area and power without sampling rate degradation because the 64 TIAs share a variable gain amplifier (VGA) which needs large area and high power due to resistive feedback. In addition, the SAR-ADC is designed for low power with modified algorithm where the operation of the lower bits can be skipped according to an input voltage level. The operation of ADC is controlled by a digital controller based on UART protocol. The data of ADC can be monitored on a computer terminal. The signal readout circuitry was designed with 0.13${\mu}m$ CMOS technology. It occupies the area of 0.173 $mm^2$ and consumes 77.06${\mu}W$ at the conversion rate of 640 samples/s. According to measurement, the linearity error is under 5.3% in the input sensing current range of 10nA - 10${\mu}A$. The UART I/O and the digital controller were designed with 0.18${\mu}m$ CMOS technology and their area is 0.251 $mm^2$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.4A
• /
• pp.439-446
• /
• 2004

This paper describes high speed and low power design techniques for an 8-bit 500MSamples/s CMOS 2-step ADC. Instead of the conventional closed-loop architecture, the newly proposed ADC adopts open-loop architecture and uses a reset-switch to reduce loading time in an environment of big parasitic-capacitances of mux-array. An analog-latch is also used to reduce power consumption. Simulation result shows that the ADC has the SNDR of 46.91㏈ with a input frequency of 103MHz at 500Msample/s and consumes 203㎽ with a 1.8V single power supply. The chip is designed with a 0.18mm 1-poly 6-metal CMOS technology and occupies active area of 760${\mu}{\textrm}{m}$*800${\mu}{\textrm}{m}$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.23-29
• /
• 2011

A dB-linearity improved variable gain amplifier (VGA) for GPS receiver is presented. The Proposed dB-linear current generator has improved dB-linearity error of ${\pm}0.15$dB. The VGA for GPS is designed using proposed dB-linear current generator and composed of 3 stage amplifiers. The IF frequency is assumed as 4MHz and the linearity requirement of the VGA for GPS receiver is defined as 24dBm of IIP3 using cascaded IIP3 equation and the VGA satisfies 24dBm when minimum gain mode. The DC-offset voltage is eliminated using DC-offset cancelation loop. The gain range is from -8dB to 52dB and the dB-linearity error satisfies ${\pm}0.2$dB. The 3-dB frequency has range of 35MHz~106MHz for the gain range. The VGA is designed using 0.18${\mu}m$ CMOS process. The power consumption is 3mW with 1.8V supply voltage.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2387-2394
• /
• 2013

A low spur phase-locked loop (PLL) with FVCO-sampled feedforward loop-filter has been proposed. Conventional PLL has loop filter made of a resistor and capacitors. The proposed PLL is working stably with the filter consisted of capacitors and a switch. It has been designed with a 1.8V $0.18{\mu}m$ CMOS process and proved by simulation with HSPICE.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.12
• /
• pp.33-39
• /
• 2013

There have been studies in improving jitter characteristic of delay locked loop (DLL) even it has a shorter jitter that of phase locked loop (PLL). These studies result in numerous architectures of DLL which improve jitter performance. The paper shows that the jitter characteristic can be improved with various loop filters in DLL. It has been designed with 1.8V $0.18{\mu}m$ CMOS process.