It is not an overstatement to say the factory are the number one cause in creating environmental load. However, only a few studies have been done upto this date on environmentally friendly factory. Thus, This study is to present the characteristics of environmentally friendly factory. A survey of current literatures and cases show the characteristics of environmentally friendly factories and buildings and environment assessment method and plan. To better measure the environmentally friendly qualities as written in literature across the globe, classification system was constructed. The classification system was made and important factors were found based on the precedent paper on environmentally friendly building plan and environment assessment method at building and cases and abroad in the literature review. The classification used 4 different sectors : Land & Transportation, Architectural Planning Technique, Environment & Equipment, Energy & Material. Within these 4 sectors 33 discrete factors are applied to the factory according to literature and case review and specialist advice.

To act and respond to the climate changes and to bring about power-saving in buildings, the changes in the atmospheric data in Korea are recorded and assessed. For the two regions representative of Korea, the data obtained from HadCM3 and actual data are compared and analyzed so as to concretely evaluate and confirm the changes taking place in the cooling and heating degree days in Korea. For the past 40 years, from 1996 to 2005, the number of heating degree days was on the decline and in the two representative regions, between 1980's and 1990's, the number of decrease in the heating degree days had been quite large. The number of cooling degree days showed a trend of increase since the 1970's and just as in the case of heating degree days, the extent of increase was quite large between the 1980's and the 1990's. The results of comparison of the number of heating and cooling degree days, one obtained from the "Korea Meteorological Administration" and another from the HadCM3 data (E127.5,N37.5,E127.5,N35), which is one of the ways of predicting the climate, showed similar trends in the number of heating degree days in the Yeosu area. However, in the case of the number of heating degree days in Seoul and the number of cooling degree days both in Seoul and Yeosu, the differences in the number ranged from a minimum of 300 days to a maximum of 1500 days. This could be attributed to the grid points used in the HadCM3, the differences in the values of latitudes and longitudes of these two locations considered in this study, topographical differences, heat island effect caused by population density etc. and while using the HadCM3, these variables factors must be taken into consideration.

It is common to design the duct branches where to supply the required air flow for individual room in residential apartment house. However it is difficult to adjust the air volume adequately in small air duct branches in residential ventilation system. The purpose of this study is to figure out the performance of Multidrop chamber coupling system for the residential ventilation system. The experiments were designed to simulate apartment of $84m^2$ and established multidrop chamber duct and general duct on the ceiling of the apartment. Distribution performance of air supply rate were evaluated in this experiments. As a result, distribution performance of air supply rate in the general duct is different from designed air supply rate by about 35% ~ 50% and about 10% in the multidrop chamber system. In additional the sound insulation performance of the multidrop chamber system decreased about 20% compared with general duct system. Therefore, the multidrop chamber system is considered to satisfy proper air supply rate of each room and to improve the sound insulation performance in apartment Houses.

Standard sound source currently used in heavy-weight floor impact sounds that cause many social problems has excessive low-frequency energy within a range from 63 Hz to 125 Hz, and is difficult to evaluate and measure. To solve these problems, studies are widely performed using a new impact source, the impact ball. In this study, the sound fields in a receiving room were compared and analyzed according to the current impact source, the bang machine, and the impact ball. And deviation of sound pressure level according to the impact source positions were compared. In case of impact ball, the sound pressure level was lower at 63 Hz and below and higher at 125 Hz and above. The same trend was observed at the low-frequency range on the horizontal and vertical planes, regardless of the type of the impact source, which showed the influence of the room mode. There was a problem with the variations in the sound pressure level according to the size or shape of the receiving room. And it also shows that change of source positions may effect the single number rating scheme.

Artificial ground greening has been developed gradually in accordance with increasing demands of out-door space in Apartment complexes. Nowadays other social demand, environmental load abatement, needs qualitative growth of artificial ground greening as well as quantitative growth. So the objects of this study would be seizing and analyzing changeable items in artificial ground greening in the future, and show drafting materials for the development of spheres in connected with artificial ground greening. For this study, Delphi method was applied. First, three groups of panel, 48 people, were selected. Second, set up items of changes possible in the future from the first questionnaire and additional inquiry. Third, made up the second questionnaire of change possible in the future with Likert summated scale, and finally one way - ANOVA executed; independent variables were items of changes, and dependent variables were three groups of panel. To conclude, although limits of this study, we could glance over general flows and changes in artificial ground greening, and discover items which are hardly changeable and necessary to change in present condition of artificial ground greening.

Photovoltaic-thermal(PVT) collectors are a combination of photovoltaic modules with solar thermal collectors, forming one device that receives solar radiation and produces electricity and heat simultaneously. The PVT collectors can produce more energy per unit surface area than side by side PV modules and solar thermal collectors. There are two types of water type PVT collectors, depending on the existence of glass cover over PV module; glass-covered(glazed) PVT module, which produces relatively more thermal energy but has lower electrical yield, and uncovered(unglazed) PVT module, which has relatively lower thermal energy with somewhat higher electrical performance. In this paper, the experimental performance of two types of the water-based PVT combined collectors, glazed and unglazed, was analyzed. The electrical and thermal performances of the PVT combined collectors were measured in outdoor conditions, and the results were compared.