The effect of sodium gluconic acid on the collapsability of the sodium silicate type $CO_2$ mold was studied. The bending strength was saturated with gassing $CO_2$ for 60 sec. under $1kg/cm^2$ and with the flow rate of $10\;{\ell}\;/min$. It was decreased with aging after having been fully hardened. The retained strength was reduced in the heating temperature range of $100{\sim}1,100^{\circ}C$ and the retained strength peak near the heating temperature of $100^{\circ}C$ was removed by the effect of the sodium gluconic acid. Silica gel, $Na_2CO_3$ and dehydrated sodium silicates were formed from the binder of sodium silicate with the addition of sodium gluconic acid at the heating temperature of $100^{\circ}C$. $Na_4SiO_4$ was formed by the reaction of $Na_2O$, from decomposed $Na_2CO_3$, with the dehydrated sodium silicate at $500^{\circ}C$. The crystobalite type of $SiO_2$ was formed at $900^{\circ}C$. The sodium gluconic acid had no effect on the bending strength at around $1,100^{\circ}C$ due to the combustion loss of it.

For Pb-20wt%Cu alloys, severe macrosegregation due to density difference of the resulting phases in normal directional solidification has been minimized and a uniformly aligned dendritic structure has been produced by axially rotating the sample of 5mm diameter in conjunction with horizontal directional solidification. Under the constant growth velocity of $20{\mu}m/sec$, increasing the rotation rate from 0.18 to 12rpm results in a transition from an aligned columnar to an equiaxed Cu-dendritic structure. With a constant rotation rate of 0.18rpm, increasing the growth velocity from 10 to $50{\mu}m/sec$ also has promoted a transition from columnar to equiaxed structure.

일방향 응고법을 이용하여 텔루리움(Te)이 Fe-C-Si 합금 즉 주철의 응고시 흑연의 형태에 미치는 영향을 관찰하였다. Te이 산소와의 반응성향이 큼을 감안하여 수소 및 아르곤으로 응고분위기를 조절함으로써 각각의 분위기에서 나타나는 Te의 영향을 비교 분석하였다. 그 결과 아르곤 분위기에 비하여 수소분위기에서 Te의 효과가 현저하였으며, 이것은 수소가 산소의 영향력을 억제하여 Te의 산화를 방지함에 기인하는 것으로 판단되었다. 수소 분위기 하에서 Te의 효과가 극대화되었을 경우 희주철 조직은 응고속도가 극히 낮은 때에만 얻어졌으며, 미세한 편상(片狀)흑연이 평면형 응고선단을 형성하며 열전달이 일어나는 반대 방향을 따라 성장함으로써 지금까지 볼 수 없었던 독특한 조직이 관찰되었다.

This study describes the influence of the trace amount of sulphur on the nucleation behavior of graphite crystals in high purity Fe-C-Si alloys prepared by levitation melting method. Detailed microstructural analyses of high purity(HP) and sulphur added(HP＋S) samples showed that the nucleation of graphite crystals was prevented by sulphur. With decreasing the sulphur content, the shape of graphite crystals tended to spherulitic, and below 2ppm S, that of graphite crystals was only nodular. The critical cooling rate for the nucleation of griphite crystals was calculated as $1.5{\times}10^3k/s$. It is obvious from this work that residual C-C clusters act as an effective nucleation site for graphite crystals and one of the important role of nodularizing elements is to act as scavenger which removes harmful impurities from the solution.

Aluminium-silicon alloy(JIS AC8A) matrix composites reinforced with SiC particles were fabricated by spray-cast forming process, and the microstructure of powders and preforms produced were studied by using an optical and scanning electron microscopy. SiC particles were co-sprayed by mixed phase injection method during the spray casting process. Most of the composite powders formed by this mixed phase injection method exhibit morphology of particle-embedded type, and some exhibits the morphology of particle attached type due to additional attachment of the SiC particles on the surface of the powders in flight. The preforms deposited were resulted in dispersed type microstructure. The pre-solidified droplets and the deposited preform of SiC-reinforced aluminium alloy exhibit finer equiaxed grain size than that of unreinforced aluminium alloy. Eutectic silicons of granular type are crystallized at the corner of the aluminum grains in the preforms deposited, and some SiC particles seem to act as nucleation sites for primary/eutectic silicon during solidification. Such primary/eutectic silicons seem to retard grain growth during the continued spray casting process. It is envisaged from the microstructural observations for the deposited preform that the resultant distribution of SiC injected particles in the Al-Si microsturcture is affected by the amount of liquid phase in the top part of the preform and by the solidification rate of the preform deposited.

The effects of weld repair on the durability in Al-10%Si-0.3%Mg castings were evaluated. The strength and fracture toughness in fusion zone were higher than those in the base metal by rapid cooling of fusion zone after welding. There were no significant differences between fatigue properties in castings and weld repaired specimen as the results of low cycle fatigue and rotating bending fatigue test. Therefore it was concluded that weld repairing did not have any significant effect on the mechanical properties of castings.

Grey iron containing a small amount of Cu and Mo to improve the effect of heat treatment and microstructures were poured in to the mold and them austenized at $900^{\circ}C$. After austenitizing the specimens of castings were austempered $210^{\circ}C$, $250^{\circ}C$, $300^{\circ}C$ and $350^{\circ}C$. The effects of matrix structures, mechanical properties and wear characteristics were investigated by austempering temperatures. Tensile strength and hardness of austempered grey iron are increased and the amount of retained austenite is decreased as austempering temperature is lower even though the amount of retained autenite in it only 4%. The amount of rolling wear loss are increased as rolling revolution is increased and wear loss of austempered grey iron under dry rolling condition is characterized by three models; initial wear, stationary wear and abnormal wear. It has been found that the amount of wear loss was increased with increasing maxium compressive stress and rolling revolution.

The horizontal continuous casting process with the heated mold was applied to obtain the unidirectionally solidified rods($4{\sim}8mm$ dia.) of pure copper with good surface quality. The results could be summarized as follows. 1. The unidirectional solidification of pure copper rods with good surface(mirror surface) quality could be obtained by placing the S/L interface inside the heated mold cavity even though the cast copper rods were covered with thin copper oxide layer. 2. The casting speed for 4mm dia. rods with mirror surfaces was affected significantly by the mold-cooler distance rather than the cooling flow rate when other casting conditions were fixed. 3. The casting speed was the main factor affecting the oxidation of copper during the continuous casting and the thickness of copper oxide layer decreased almost linearly as the casting speed increased.

The effects of varying the pouring temperature and the die preheating temperature in producing centrifugally cast HP alloy modified with Nb was evaluated on the basis of the resultant macrostructure, microstructure and hardness of these castings. Increased die preheating temperatures and pouring temperatures resulted in an increase in the thickness of the columnar dendritic zone, the primary and secondary dendrite arm spacing and the thickness of the zone of porosity at the casting I.D.(inner diameter). Lower die preheating temperature and pouring temperatures result in increased grain fineness and an increased zone of equiaxed grains. A higher hardness was achieved toward the casting O.D.(outer diameter) compared to the casting I.D., attributable to alloy segregation toward the casting I.D. and segregation differences resulting from reduced solidification cooling rates toward the casting I.D. Also, a higher hardness was realized at the cold end of the casting attributed to a more uniform distribution of carbides.

Water modeling experiments and computer simulation for the predictions of defects of die castings are very important to produce high quality castings with less cost. The relation between the variable air vent system and the characteristics of the fluid flow in the die cavity is studied by using water modeling tests, which give ideas on reasonable designing of die cavity, vent arrangement and gating system. In order to test the water modeling, injection is done by using water containing NaCl. Flow behaviors in cavities are visualized by high speed camera and video tape recorder, and local filling time is measured with electrode sensors. Special attention is paid to the configuration of die cavity. Simulated results by computer are examined and compared with the results of water modeling experiments. There are close correlations between the simulated results and water modeling ones.