Decarburization phenomena of SM50C steel casted in ceramic mold was investigated. As result, decarburized depth increased by increased by increasing the volume-to-surface area ratio and mold temperature. And the relations between them is $y(cm)=(1.96{\times}10^{-5}T+0.0135)\;{\times}M-1.05{\times}10^{-5}T+9.73{\times}10^{-3}$. When mold is controlled by Ar ags, reducing atmosphere, decarburized depth is decreased. In case of adding graphite powder in the mold, decarburization is decreased more. Specially, when graphite powder is added on the mold materials and the wax is layed on the mold, decarburization is almost prevented.

Steel and iron castings made with expandable polystylene (referred to hereafter as EPS) patterns are often affected by distinctive defects associated with incomplete decomposition of the EPS as the molds are filled with metal. The effects of practical factors on carbon pick-up were investigated on the specimens, by taking successive layers of swarf and analysis, whereas the lustrous carbon is determined by using combustion analysis. The quality of the castings, with particular reference to carbon pick-up in low carbon steel and lustrous carbon on gray iron, is further influenced to a significant extent by such practical factors as reduced pressure, the pouring temperature, the density of EPS pattern, the additive in coating and in pattern and the casting thickness. The rate at which carbon pick-up and lustrous carbon deposites are formed can be reduced by reducing the density of the pattern and also reducing pressure, especially by adding $Na_2CO_3$ in coating and in pattern to promote $CO_2$ evolution. The upper parts of castings obtained using EPS patterns are slightly higher in carbon pick-up and in lustrous carbon than other parts.

Diamond is the hardest material known to humans, also possesses the highest thermal conductivity and a very low thermal expansion coefficient. Therefore, these properties of diamond make them logical choices for many difficult grinding application. Bonding material is a very important factor to performance of a grinding wheel. Grinding glass constitutes one of the major application areas of diamond grinding wheels, and Cu-Sn tin bronze matrix is widely used as a metal bond of diamond wheel in grinding glass but these studies are rarely reported. The bronze test pieces excluding diamond are sintered by the method of hot sizing respectively at $600^{\circ}C$, $650^{\circ}C$, $700^{\circ}C$, with a composition(Cu-10wt%Sn) on ${\alpha}$ phase and two compositions(Cu-20wt%Sn and Cu-23wt%Sn) on ${\alpha}+{\beta}$ phase. The rupture strength of Cu-10wt%Sn is highest. The bronze bonded diamond wheels are manufactured by same conditions as the bronze test pieces. The results of grinding ratio of wheels are highest in case of Cu-10wt%Sn bonded wheel sintered at $650^{\circ}C$ and grinding power is highest in same composition sintered at $700^{\circ}C$.

Particle-reinforced metal matrix composites via the Osprey spray casting process were fabricated by injecting second phase particles of $Al_2O_3$(＜$40{\mu}m$) and W($6{\mu}m$) into the spray of Cu droplets, and the thermal behaviors of the composite droplets during flight were considered theoretically on the basis of mixing modes between the Cu droplets and the reinforced particulates injected. It was found that the W-injected spray is comprised of particle-embedded droplets, and the $Al_2O_3-injected$ spray comprises particle-attached droplets. From the predicted results of the thermal behaviors of the composite droplets and preforms produced, it is concluded that the thermal behaviors of the composite droplets during flight, and during the subsequent deposition are strongly influenced by its mixing modes between the reinforced particulates and Cu droplets during flight.

Aluminum alloy matrix composites reinforced with various amounts of SiC particles have been produced by rheo-compocasting followed by hot extrusion. A relatively uniform distribution of SiC particles in the composites was obtained. The amounts of pore and SiC particles cluster were relatively small in the composites. Particle free zones were observed in the hot extruded composites when the amount of SiC particles was less than 20 vol%. However, the width of particle free zone decreases with the increase of SiC particle content. Eutectic Si phase play an important role for improving bonding between SiC particle and matrix. Tensile and yield strength increased with the increase of SiC particle content. the strenthening effect of SiC particle addition was effective even at relatively high temperature of 573 K.

In Al-Pb monotectic alloys Pb particles are difficult to uniformly distribute over the Al matrix because of the gravity segregation of pb element. Therefore the effects of centrifugally spray casting process on microstructures and distributions of Pb particle were investigated. As the preform thickened the sine of Pb particle became larger, the amount of porosity became lower and microstructures showed the change from spray-deposition microstructures in the lower part of the preform to spray-casting microstructures in the upper part of it. The size of Pb particles, amount of porosity and splat layer boundaries in hot forged preform showed still less than of as-deposited preform.