Proceedings of the Korean Society of Marine Engineers Conference (한국마린엔지니어링학회:학술대회논문집)
The Korean Society of Marine Engineering
- 기타
Domain
- Machinery > Naval Architecture/Ocean Engineering
2005.06a
-
This paper addresses the analysis of the combustion characteristics in the oil burner using swirl flow. The reduction of exhaust emissions and high efficiency combustion techniques of the industrial burner have been studied to conserve environmental resources. We make swirl burner equal to dimension of wide burner and it is turn round of the combustion gas in construction. For a vigorous inner flow possessde 3m/s velocity in combustion gas of two burners. In calculation, we make use of a densely mesh to detailed analysis. In this study, the effect of swirl flow on the combustion of a commercial burner is analysed by experimental and also simulative manner. The results show the swirl burner has 40% better efficiency and less emissions of CO, HC, NOx and Smoke.
-
It becomes necessary for engine manufactures to verify whether lots of engines on test bed during shop test are in compliance with NOx Technical Code for marine diesel engines more efficiently on the basis of engine group test concept which contains parent engine and member engines since all the engines are not needed to take NOx measurement. In addition, it becomes more obliged to consider parameters which affect NOx emission level and describe these parameters in NOx technical file as engine information and settings to define engine operation range with tolerance to make sure the engines are still in compliance with NOx emission limit on board after shop test. During preparation of engine group test for 4-stroke marine diesel engines, we evaluated NOx emission value under different engine operating conditions and found that there are certain parameters, for example, Charge air temperature and Max. cylinder pressure which have influence on NOx emission level. The NOx emission shall be satisfied with NOx technical code by means of controlling such parameters.
-
The purpose of this study is to develop venturi type after-burner in order to obtain pollutant reduction effect and find the best stable combustion condition. For this purpose, through a flow analysis, the shape of venturi type was made and flame holder locations were also decided by measuring chemical species at before and after the after-burner. Also, various chemical species concentration were measured at changing the induced air rates and the oxygen for oxygen enrichment for the solution the problems of much oxygen flow rate and the flame stability range. As results of this study, a flow distribution and the purification effect was excellent at venturi contraction 0.5 and flame holder location 12mm below the center of Venturi throat. On the purification characteristics, we found that pollutants reduction was effective when area ratio and oxygen are increased. But there are suitable quantities due to the flame shape change and combustion efficiency.
-
Experiments at the Japan Microgravity Center(JAMIC) have investigated the interaction between diffusion flames and solid surfaces placed near flames. The fuel for the flames was
$C_2H_4$ . The surrounding oxygen concentration was 35% with temperatures of$T_a$ =300. Especially, the effect of wall temperature on soot deposition from a diffusion flame placed near the wall has been studied by utilizing microgravity environment, which can attain very stable flame along the wall. Cylindrical burner with fuel injection was adopted to obtain two dimensional soot distributions by laser extinction method. In the experiment two different wall temperatures,$T_w$ =300,800K, were selected as test conditions. The results showed that the soot distribution between flame and burner wall was strongly affected by the wall temperature and soot deposition increases with decrease in wall temperature. The comparison among the values for two different wall temperatures suggested that the change in thermophoretic effect is the most dominant factor to give the change in soot deposition characteristics. -
Since HiMSEN H21/32, a new medium speed diesel engine of Hyundai's own design, was introduced in 2001, Hyundai has added new models of H25/33 and H17/28 into HiMSEN engine family. These two new engines take after faithfully to the original HiMSEN concept of a PRACTICAL engine by Hi-Touch and Hi-Tech. The prototype of H25/33 was developed jointly with Rolls Royce Bergen originally and also introduced in 2001. But most of the engine design have been changed by Hyundai for the commercial versions to be a member of HiMSEN family, which has little interchangeability with the prototype. H17/28 is now under development as the smallest size of the family. This new engine also has the longest stroke of a class engine, which has been proven as the best basis for future environmental challenge. The higher compression ratio of 17 and optimized Miller Timing with Simplified pulse turbocharging system applied all HiMSEN engines as which showed the most practical solution against current heavy fuel combustion issues for the time being before introducing digital control system. This paper describes the design and development of these new HiMSEN engines and also reviews the service experiences of H21/32 and H25/33, which launched successfully.
-
Cylinder frame manufactured by casting is assembled with the components such as cylinder head, cylinder liner and main bearing cap, etc. The mechanical contact between all of the neighboring components due to bolt tightening was taken into consideration. The loads used in structural analysis were the bolt tightening forces induced by hydraulic jack and the dynamic forces calculated from kinematic analysis. The difference of forces between the neighboring cylinders was taken into account. The maximum stress, stress amplitude and mean stress calculated from the results of structural analyses were used to evaluate the static and fatigue strength. Gray cast iron which is material of cylinder frame has the material characteristics of very small elongation and different strength in tension and compression. Based on such an material characteristics, the strength evaluation of cylinder frame was carried out with in-house program developed internally.
-
Marine Propulsion shafting system coupled with medium diesel engine forms multi-degree torsional vibration system which consist of many inertia masses such as crank, flywheel, propeller and sometimes gear system is adopted additionally for the purpose of improving propeller's propulsion efficiency or connecting with PTO/PTI. The periodic excitation torques generated by combustion pressure in cylinder and reciprocating masses induce various kinds of vibrations in this shafting system. If the frequency of this excitation torques is equal to the natural frequency of the shafting, the amplitude of the torsional vibration increases steeply and the damage of crankshaft or gears may be occurred by that. This frequency is called critical speed. When making a plan for shafting system, it is important for this frequency to be expected exactly and not to be in commonly used speed. For this reason, this paper introduces the experimental equipment for torsional vibration of marine propulsion shafting system and describes the theoretic and the experimental methods to look for natural frequencies.
-
In proportion to the increase of industrial development, emission troubles were concerned as global issue. For these reasons, so many researchers and associated institutes effort to reduce pollution with new technology and various devices. As a kind of these methods, we used catalysts as a after-treatment system. At first, we made equipment of model furnace. And various catalysts were equipped at exhaust duct of combustion system, and excess air ratio( ), change cell numbers, catalyst materials(Pt, Pd) were changed as experimental conditions. With these various condition, temperature, NOx, CO, HC,
$CO_2$ and$O_2$ concentration were measured. As a result, NOx conversion were increased with increasing of cell number in Pd catalyst. And Pt catalyst were became 100% conversion at 200 and 300 cell. Also, Pt catalyst was better than Pd catalyst${\alpha}$ =1.5 in this condition. In addition, CO and HC concentrations were decreased${\alpha}$ =1.5 with Pd catalyst. -
The proceeding bearings of marine diesel engine are affected by dynamic loads from the cylinder gas pressure and the inertia force from the crank mechanism. Oil film must support the load of the shaft and it also must protect the proceeding and the bearings from damage. This study uses Goenka's new curve fit to carry out the theoretical analysis of oil film in proceeding bearings for MAN B&W 12K90MC-C and Hyundai Heavy Industry Co., Ltd HiMSEN H21/32 Engine. The applied engine's analysis results show the behavior of the proceedings in main and crank pin bearings. The results of this study will be the proper criteria for the proceeding bearings design and be available for development of the new technology in the proceeding bearing and for the high strength lining coating.
-
In this experiment study, to acquire elementary data for explaining to generate frost layer in the fin - tube evaporator. the experiment condition is to supply air on 0.3m/s, 0.6m/s, 0.9m/s and inlet air temperature is kept constantly
$20^{\circ}C$ , supplied air relative humidity is 70%, 80, 90%. And brine temperature in the copper tube was kept$-15^{\circ}C$ because, generally cooling temperature range is constantly$-15^{\circ}C$ in the heat exchanger for air conditioning system. in conclusion, through this experiment, we did compare with frost layer and frost quantity in each condition and examine these data -
The object of this experiment is comparing heat transfer performance and pressure drop characteristics by baffle cut rate, fluid velocity and heating temperature. Experiments were carried out in cross flow heat exchanger with water as a working fluid. In this experiment, baffle cut rate is 30%, 40%, 50%, velocity is 0.5m/s, 1.0m/s, 1.5m/s, and heating temperature is
$30^{\circ}C$ ,$40^{\circ}C$ ,$50^{\circ}C$ . An experimental device to measure the heat transfer coefficient was constructed. The experimental result were obtained for the fully developed turbulent flow of water in tube on the condition of uniform heat flux. -
Many studies have been conducted to increase heat transfer in fluid. One of the various heat transfer enhancement techniques is to suspend fine metallic or nonmetallic solid powder in traditional fluid. Nanofluid is defined at a new kind of heat transfer fluid containing a very small quantity of nanometer particles that are uniformly and stably suspended in a liquid. In this study CuNi or CuAg nano particles are used to investigate heat transfer enhancement. The result shows the thermal conductivity of nanofluid is much higher than that of traditional fluid.
-
The effect of heat conduction resistance on laminar film condensation of the pure saturated vapor in forced flow over a flat plate has been investigated as boundary layer solutions. A efficient numerical methods for water are proposed for its solution. The momentum and energy balance equations are reduced to a nonlinear system of ordinary differential equations with four parameters: the Prandtl number, Pr, Modified Jacob number,
$Ja^{\ast}/Pr$ , defined by an overall temperature difference, a property ratio$\sqrt{P_l{\mu}_l/P_v{\mu}_v}$ and the conjugate parameter${\zeta}$ . The similarity and simplified solutions obtained reveal the effects of the conjugate parameter. -
The evaporation heat transfer and pressure drop of
$CO_2$ in a small diameter tube was investigated experimentally. The experiments were conducted without oil in a closed refrigerant loop which was driven by a magnetic gear pump. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and evaporator(test section). The test section was made of a horizontal stainless steel tube with the inner diameter of 4.57 mm, and length of 4 m. The experiments were conducted at mass flux of 200 to 700$kg/m^2s$ , saturation temperature of$0^{\circ}C$ to$20^{\circ}C$ , and heat flux of 10 to 20$kW/m^2$ . The test results showed the evaporation heat transfer of$CO_2$ has great effect on more nucleate boiling than convective boiling. The evaporation heat transfer coefficients of$CO_2$ are highly dependent on the vapor quality, heat flux and saturation temperature. The evaporation pressure drop of C02 are highly dependent on the mass flux. In comparison with test results and existing correlations, correlations failed to predict the evaporation heat transfer coefficient and pressure drop of$CO_2$ , therefore, it is necessary to develop reliable and accurate predictions determining the evaporation heat transfer coefficient and friction pressure drop of$CO_2$ in a horizontal tube. -
As vehicles are recently becoming more important in our life, the study for engine capacity has been conducted for many years. Specially, the study on lubrication in the engine is needed to develop engine capacity. The role of lubrication is to reduce fraction, manage the temperature and protect from corrosion etc. At the view point of the engine, lubrication and cooling of the engine have an effect on the life and efficiency, so we have to study this problem. Ball check valve is located in the inlet of the Oil Jet. Ball check valve is used to control the flow rate of the engine oil, which cools and lubricates the engine. Flow rate at the oil jet is very important, so the study for this problem is needed to conduct researches. The point of this study is to compute the flow rate and the flow in oil jet. The results of this study is that the mass flow rate is satisfied with the research which is obtained at the experiment.
-
The sirocco fan is used to get low noise, and it has been applied to a lot of industry field like the heat engine, the fluid instrument power plant, the food industry, environment industry etc... because there are not any problem even it is mixed with a any kind of liquid, gas, and solid. The flow characteristics in sirocco fan are investigated by PIV. The experiment using PIV measurement for Test section's flow characteristics acquired velocity distribution, .Condition : when sirocco fan in automobile air controller maximum 1450RPM, and a revolution is a variation (1)950RPM, (2)1100RPM, (3)1250RPM. The agreement a experiment shows the validity of this study and the results of this study would be useful to the engineers who design for the flow systems for heating, ventilation and air conditioning.
-
Now a days Automobiles are becoming more important in our life, the study on piston of engine is needed because, piston's cooling and lubrication of piston have an effect on the life and efficiency of engine directly. So, this study is about nozzle part of oil jet for cooling piston in the automotive engine. Piston exposes combustion gas of over
$2000^{\circ}C$ and is shocked high pressure at the time of explosion shortly. Furthermore strong friction occurs by high speed rotation. The cooling system is considered from oil jet to piston. The previous system cooled the lower part of piston only. So, efficiency was low. To improve this system, make the oil gallery in the piston, and oil flows into the gallery. The value of oil flow rate into the gallery is important. Consequently, the point of this study is the research of investigation of flow characteristics for variable Re number. This study has been modelled by a commercial CFD code FLUENT, allowing to assess its validity -
3-D Numerical Analysis on a low Reynolds Number Mixed Convection in a Horizontal Rectangular ChannelA three-dimensional numerical simulation is performed to investigate on a low Reynolds number mixed convection in a horizontal rectangular channel with the upper part cooled and the lower part heated uniformly. The three-dimensional governing equations are solved using a finite volume method. For convective term, the central differencing scheme is used and for the pressure correction, the PISO algorithm is used. Solutions are obtained for A=4, Pr=0.72, 10, 909, the Reynolds number ranging from
$2.1{\times}10^{-2}$ to$1.2{\times}10^{-1}$ , the Rayleigh number is$3.5{\times}10^4$ . It is found that vortex roll structures of mixed convection in horizontal rectangular channel can be classified into three roll structures which affected by Prandtl number and Reynolds number. -
The heat transfer coefficient and pressure drop during gas cooling process of carbon dioxide in a helically coiled tube were investigated experimentally. The experiments were conducted without oil in the refrigerant loop. The main components of the refrigerant loop are a receiver, a variable speed pump, a mass flowmeter, a pre-heater, a gas cooler(test section) and an isothermal tank. The test section is a double pipe type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. It was made of a copper tube with the inner diameter of 4.85 [mm], the outer diameter of 6.35 [mm] and length of 10000 [mm]. The refrigerant mass fluxes were 200
${\sim}$ 600 [kg/$m^2$ s] and the average pressure varied from 7.5 [MPa] to 10.0 [MPa]. The main results were summarized as follows: The heat transfer coefficient of supercritical$CO_2$ increases, as the cooling pressure of gas cooler decreases. And the heat transfer coefficient increases with the increase of the refrigerant mass flux. The pressure drop decreases in increase of the gas cooler pressure and increases with increase the refrigerant mass flux. -
A Flapping foil produces an effective angle of attack, resulting in a normal force vector with thrust and lift components, and it can be expected to be a new highly effective propulsion system. A heaving foil model was made and it was operated within a circulating water channel at low Reynolds numbers. The unsteady thrust and lift acting on the heaving foil were measured simultaneously using a 6-axis force sensor based on force and moment detectors. We have been examined various conditions such as heaving frequency and amplitude in NACA 0010 profile. The results showed that thrust coefficient and efficiency increased with reduced frequency and amplitude. We also presented the experimental results on the unsteady fluid forces of a heaving foil at various parameters.
-
Automobiles are very important as modern society is developed. Increase of the number of the automobiles cause environmental problem, that is, air pollution. So, many countries are adopting a environmental law. Automobile manufacturing companies have developing methods to prevent air pollution with increase of the efficiency of automotive engines. PCV(Positive Crankcase Ventilation) system which is one of them is made by the closed loop that consists of combustion chamber, crankcase, manifold suction tube and manifold. PCV valve is attached on manifold tube to control the flowrate of blowby gas. PCV valve is an important part in this system but it is difficult to design PCV valve which satisfies the required flowrate of blowby gas. In this study, our purpose is to help a PCV valve designer with the development of a design program. We used 4th order Runge-Kutta method and Bernoulli's equation to analyze the spool dynamic motion. By the comparison between our program and experiment, we think that a PCV designer can use our program in their work place.
-
According to change of flow around a circular tube for freezing, measured a variety of salinity of frozen layer. This study was experimentally performed to investigate freezing behavior of sea water along a vertical cooled a circular tube with bubbly flow. The experiments were carried out for a variety of parameter, such as air-bubble method, cooled -tube temperature and air-flow rate. It was found that the experimental parameters gave a great influence on the freezing rate and the salinity of the frozen layer.
-
The reduction of heat transfer rate to the stored liquid hydrogen from outside condition is extremely important to keep the liquid hydrogen longer. In this paper the highly efficient support system for the liquid hydrogen storage vessel was newly developed and analysed. The support system was composed of a spherical ball in the center of supporter to reduce the heat transfer area, with its above and below supporting blocks which are the SUS and PTFE blocks inserted in the SUS tube. The heat transfer rate and temperature distribution of the support system were evaluated by FLUENT, and the thermal stress and strain were estimated by ANSYS software. The results showed that the heat transfer rate from outer vessel to inner one was extremely decreased compared with the common method which is simply SUS tubes inserted between inner and outer tanks. The thermal stress and strain were obtained well below the limited values. As a result, it was the most efficient support system of storage vessel for liquid hydrogen and most cryogenic fluids.
-
Recommand Systems are being used by an ever-increasing number of E-Commerce to help customers find products to purchase. Recommend Systems offer a technology that allows personalized recommendations of items of potential interest to users based on information about similarities and dissimilarities among different customers tastes. In this paper, we design and build a Recommend System using the historical customer movie purchase transactions and extracts the knowledge needed to make association recommendations to new customers.
-
There is few study which automatically diagnose the fault from ship's monitored signal. The bigger control and monitoring system is, the more important fault diagnosis and maintenance is to reduce damage brought forth by system fault. This paper proposes fault diagnosis system using a correlation analysis algorithm which is able to diagnose and forecast the fault and is composed to fault detection knowledge base and fault diagnosis knowledge base. For this all kinds of ship's engine room monitored data are classified with combustion subsystem, heat exchange subsystem and electric motor and pump subsystem by analyzing ship's operation data. To verifying capability of fault detection, diagnosis and prediction, Fault Management System(FMS) is developed by C++. Simulation experiment by FMS is carried out with population data set made by log book data of 2 months duration from a large full container ship of H shipping company.
-
The helicopter system is non-linear and complex. Futhermore, because of absence of accurate mathematical model, it is difficult accurately to control its attitude. therefore, we propose a WAVENET control technique to control efficiently its elevation angle and azimuth one. Wavelet neural network(WAVENET) can construct systematically initial neural network as applying wavelet theory to feedforward network. It is proved through computer simulation that WAVENET has more excellent approximation capability than existing neural network. The simulation results using MATLAB are introduced.
-
PID controller is widely used in industries until now. The reason is that the structure is very simple, and that it is easily estimated in terms of hardware, and that it doesn't need a lot of parameters which should be tuned. Therefore, DC motor also uses PID controller. In this paper, a method is proposed to identify parameters of a DC motor system using a RCGA prior to design of PID controller. The model identified using a RCGA is verified through simulations.
-
The conventional PID controller has been widely used in many industrial control system because engineers can easily understand how to deal with three parameters of PID controller. The conventional tuning methods, however, have a tendency depend on experience and experiment. In this paper a real-coded genetic algorithm is used to search for the optimal parameters of PID controller for marine diesel engine. Simulation results compared with conventional PID controller tuning methods show the effectiveness and good performance of proposed scheme.
-
The system parameters of gas turbine engine tend to change remarkably in real operating condition. It means that operators have to consider environment and suitably control fuel flow. The conventional PID controller, however, can not guarantee good control performance in the aspect of system parameter change. This paper, therefore, proposes a scheme for integrating PID control and fuzzy technique to obtain the good performance of gas turbine engine speed control on the whole operating range. The effectiveness of the proposed fuzzy PID controller is verified through computer simulation.
-
Almost ship monitoring systems are event driven alarm system which warn only when the measurement value is over or under set point. These kinds of system cannot warn while signal is growing to abnormal state until the signal is over or under the set point and cannot play a role for preventive maintenance system. This paper proposes fault diagnosis method which is able to diagnose and forecast the fault from present operating condition by analyzing monitored signals with present ship monitoring system without additional sensors. By analyzing this data having high correlation coefficient(CC), correlation level of interactive data can be understood. Knowledge base of abnormal detection can be built by referring level of CC(Fault Detection CC, FDCC) to detect abnormal data among monitored data from monitoring system and knowledge base of diagnosis built by referring CC among interactive data for related machine each other to diagnose fault part.
-
In this paper, a state steering strategy using digital control method for chained system is presented. The chained system can be derived from the velocity or acceleration constraints that cannot be integrable. Especially, the chained system derived from an acceleration constraints is called the high order chained system. Such a system classified as a nonholonomic systems and cannot be controlled to its equilibrium points by continuous and time-invariant controller. Therefore discontinuous and time varying controller should be applied to control nonholonomic system. Using variable transformation, two sub system can be obtained from the chained or high order chained system. Deadbeat control and iterative state steering methods are proposed to control the systems that obtained from the variable transformation. Simulation results are given to show the effectiveness of the proposed control scheme.
-
The following is final report for governor upgrade for PWR NPP safety related EDG Kori NPP No.2 Unit. The upgraded system includes more beneficial function like as "Slow start with starting ramp", "Generator load sensing & control capability" and "Emergency ramp during slow start". This paper show functional operation of slow start regime according to NRC regulatory guide which guide regulation to NPP safety related environment.
-
A lighting control switch, extended to incorporate a power line communication technology, is developed. The system uses not an exclusive microprocessor but a general one, and developed PPM protocol. The coupling circuit is a type of an isolation LC filter, and the impedance of the circuit was designed as low as possible to extend signal transmission distance. The frequency of the carrier, considering the data length and signal attenuation as the length of power lines, was set at 250 kHz. Tests on a prototype in an indoor power lines have shown that the switch has a stable operation with the distance of power lines
-
This paper presents an electronic ballast using a step down converter, a low frequency inverter for high intensity short-arc discharge lamp. The proposed ballast is composed of a full-wave rectifier, a step down converter operated as a current source with power regulation and a low frequency inverter with external ignition circuit. The ignition circuit generates high voltage pulse of
$3{\sim}5[kV]$ peak, 130[Hz] periodically. Moreover, it is able to reignite at regular intervals by protective circuit. As experimental results on the test, acoustic resonance phenomenon is eliminated by operating the low frequency square wave voltage and current. Lamp voltage, current and consumption power are measured 123.8[V], 8.1[A] and 1,002[W], respectively. It was confirmed that the designed ballast operate the lamp with a constant power. -
In this paper, four quadrant CBPS(Compact Bipolar Power Supply) which development and study using universal PWM controller. The CBPS has 24V DC-link voltage, +/-5A output current, 50kHz switching frequency and 30Hz full load bandwidth using FET device. Proposed system has two independent PWM controllers for each full-bridge switch leg drive and PI control loops for current regulations. It is shown experimental results that good step response of the current output.
-
In this paper, a methodology for estimating the parameters of a discrete-time system and designing a digital PID controller based on the estimated model and a genetic algorithm is presented. To deal with optimization problems occurring regarding parameter estimation and controller design, a pseudo parallel genetic algorithm (PPGA) is used. The parameters of a discrete-time system are estimated using both the model technique and a PPGA. The digital PID controller is described by the pulse transfer function and its parameters are tuned based on both the model reference technique and another PPGA. A set of experimental works on two processes are carried out to illustrate the performance of the proposed method.
-
Park, Jong-Il;Rhyu, Keel-Soo;Cho, Kwon-Hae;So, Myoung-Ok;Kim, Tae-Jin;Won, La-Kyoung;Lee, Tae-Lin;An, Jong-Gab 321
These days, it is needed that more stability and reliability of Diesel engine. So it is essential that a systematic and comprehensive fault diagnosis analysis technology. this technology makes fault diagnosis analysis system more efficient. Expert System is required to make fault diagnosis analysis system. In this paper, fault and early diagnosis system is implemented to use Expert System development tools. -
Aircraft composite structure with honeycomb core experiences core crush problem in manufacturing. To prevent core crush additional processes are needed such as core stabilization and prepreg material tie-down and this is the cause of increasing cost. Recent study shows that high friction prepreg prevent core crush without additional process. This paper presents the analysis of high frictional material which attracts lots of interests through physical property, mechanical property and microscopic
-
The grain structure, dislocation density and second phase particles in various regions including the stir zone(SZ), thermo-mechanically affected zone(TMAZ), and heat affected zone(HAZ) of a friction stir weld 6.35mm thick aluminum 7075-T651 alloy were investigated and compared with the base metal. The microstruectures of nugget zone were compared according to tool rotation speeds and tool transition speeds. The hardness profiles of nugget zone were increased, while decreasing rotation speed and increasing welding speed. The optimal microstructure was gained at the low rotation speed 800rpm and th high welding speed 124mm/min. The nugget microstructures of fracture surface, transgranular dimple and quasicleavage type were showed different fracture type with the HAZ, shear fracture type.
-
Laser material processing is a very fast growing technology for various industrial applications, because of many advantages. Its major advantage of less and controlled heat input has been exploited successfully for the very critical application of aluminium alloy welding. This study suggested the occurrence source of weld-defects and its solution methods in a welding of lithium ion battery by pulsed Nd:YAG laser. In experiment, battery case has changed over joint geometry from welding of side position to flat one. In case of a electrolyte injection hole in order to seal it, welding is carried out after pressing Al ball. At this time, an eccentric degree, contact length and gap are worked as a major parameters. As improving the method of Al ball pressing, it was able to reduce an eccentricity, increase the contact length and decrease gap. As a results of a experiment, a sound weld bead shape and crack-free weld bead can be obtained.
-
The cylinder liners of low speed engine are one of a important equipment in merchant ship. But, the precision machining method of cylinder liner is not developed sufficiently. This paper shows a new honing method using by CBN honing stones.
-
This paper showed mechanical properties and behaviors of macrostructures for specimens welded by F.S.W according to welding conditions and tool with 6.35
$mm_t$ aluminum 7075-T651alloy plate. It resulted in defect-free weld zone in case tool rotation speed was 800rpm, 1250rpm and 1600rpm respectively that transition speed was changed to 15mm/min, 61mm/min and 124mm/min with tool's pin diameter 4${\Phi}$ mm and 6${\Phi}$ mm. The optimum mechanical property, ultimate stress,${\sigma}_Y$ =470Mpa was obtained at the condition of 124mm/min of travel speed with 800rpm of tool rotation speed using full screw type pin, shoulder dia. 20${\Phi}$ mm, pin dia.6${\Phi}$ mm and pin length 6mm. The full-screw type and the half-screw type pin showed the similar behaviors of weldability. It is found that the size of nugget was depended on tool transition speed and tool dimension by macrostructures of the cross section of weld zone. -
The using of composite material is an aviation field but it changes into a general industry. Especially composites are expanding the use on transportation vehicles like automobiles, ships, and aircraft. The main factor of this expansion is high specific strength. It can supply a high quality and efficiency of energy. But manufacturing of composite products requires many raw materials and tooling cost for special process, so we needs a reduction of these costs to achieve best efficiency. In the present study, we contrast the change of mechanical and physical properties between VaRTM(Vacuum Assisted Resin Transfer Molding) and hand lay-up process. VaRTM process can offer a high quality the same as autoclave products, and low cost like hand lay-up process. In the results of mechanical tests, VaRTM specimen is stronger than hand lay-up specimen and hand lay-up specimen became delamination. In the results of physical tests, the resin content of VaRTM specimen is lower than hand lay-up specimen. On micrograph, the strength of specimen by VaRTM between fiber and resin is stronger than that of one by hand lay-up. And the specimen by hand lay-up contains more defects than one by VaRTM. So, VaRTM process can practically apply for automobile engine hood. This paper shows that VaRTM process is one of the most suitable processes for composite parts of automobile.
-
An electrochemical evaluation on the corrosion resistance for heavy anticorrosive paint was carried out for 5 kinds of heavy anticorrosive paints such as High solid epoxy(HE), Solvent epoxy(SE), Tar epoxy(TE), Phenol epoxy(PE), and Ceramic epoxy(CE) as parameters of DFT(Dry Film Thickness, 25
${\mu}m$ 50${\mu}m$ , solution condition(Flow of Nonflow). Corrosion current density of HE(DFT 50${\mu}m$ in case of flow condition was larger than that of nonflow condition. However, their values of the other anticorrosive paints were decreased compared to the nonflow condition. The values of AC impedance were increased with increasing of DFT regardless of kinds of anticorrosive paints. And the polarization resistance of cyclic voltammogram showed a good tendency to correspond with well the values of AC impedance measurement. HE and CE had a relatively good corrosion resistance than other heavy anticorrosive paint. -
A typical honeycomb sandwich panel consists of two thin, high-strength facings bonded to a thick, light-weight core. Each component by itself is relatively weak and flexible, but when it combind in a sandwich panel they produce a structure that is stiff, strong, and lightweight. In addition to use in honeycomb sandwich panels, honeycomb is used for energy absorption, radio frequency shielding, light diffusion, and to direct air flow.Accordingly, the usage of honeycomb sandwich structure is very widely applied to the aircraft, the automobile, and marine industry, etc., because of these advantages. Generally, this honeycomb sandwich structure is manufactured by autoclave process.In this study, the honeycomb sandwich structure was produced by prepreg. To prove the suitability the honeycomb sandwich structure with prepreg, The optimum design of the skin materials and honeycomb sandwich structure were evaluated with the theory of stress analysis.
-
The ship hull part is always exposed to severe corrosive environments. Therefore, it should be protected in appropriate ways to reduce corrosion problems. So there are two effective methods in order to protect the corrosion of ship hull. One is the paint coating as a barrier between steel and electrolyte (seawater) and the other is the cathodic protection(CP) supplying protection current. In the conventional design process of the cathodic protection system the required current densities of protected materials have been used. However, the anode position of field or laboratory experiment for obtaining the required current density for CP is significantly different from anode position for real structures. Therefore, the recent CP design must consider the optimum anode position for potential distribution equally over the ship hull. The CP design companies in the advanced countries can obtain the potential distribution results on the cathodic materials by using the computer analysis module. This study would show how to approach the potential analysis in the field of corrosion engineering. The computer program can predict the under protection area on the structure when the boundary condition and analysis procedure are reasonable. In this analysis the polarization curve is converted to the boundary condition in material data.
-
This paper proposed a miniaturization passive element employing the multiple microstrip line. As a result of this method, we realized the transmission line miniaturized. The applying structure designed and evaluated a power divider on GaAS MMIC circuit. It draws a plan in a center Frequency as the observation could do good characteristic.
-
In this paper, we propose an active 90
$^{\circ}$ phase divider for application to MMIC. Because of their very large size, conventional passive 90$^{\circ}$ dividers can't be integrated on MMIC. Therefore, highly miniaturized 90$^{\circ}$ dividers are required for a development of highly integrated MMIC. For this reason, active 90$^{\circ}$ divider is indispensable because active phase divider is much smaller than conventional passive dividers, and it can be integrated on MMIC. In this work, we developed active 90$^{\circ}$ divider with emitter inductor, and it was employed for the operation of the balanced mixer in order to verify the performance of the active 90$^{\circ}$ divider. According to the results, it was found that the active 90$^{\circ}$ divider exhibited good RF performances comparable to conventional passive power dividers. -
In this paper we propose low-impedance and miniaturized a wilkinson power divider on MMIC passive component which was fabricated by a novel microstrip line structure employing periodically perforated ground metal (PPGM). The novel microstrip line structure showed much lower impedance and shorter guided-wavelength than conventional one. Using the novel microstrip line with periodically perforated ground metal, a miniaturized 17
${\Omega}$ power divider was fabricated. The line width of the power divider was 20${\mu}m$ , and the size of it was 0.110$mm^2$ , which is 21 % of conventional one. The power divider exhibited good RF performances from 10 to 20 GHz. -
Using the novel microstripline with periodically perforated ground metal, a miniaturized 1/4
${\lambda}$ transformer was fabricated. The line width of the 1/4${\lambda}$ transformer was 20${\mu}m$ and the size of it was 0.0085$mm^2$ , which is 1.2% of conventional one. The 1/4${\lambda}$ transformer exhibited good RF performances from 10 to 25GHz. -
We prepared paint-type and sheet-type EM wave absorbers with Mn-Zn Ferrite, Ni-Zn Ferrite, Ba Ferrite, Sr Ferrite, and Sendust against ghosts of a mater in ships. To prepare the absorbers, enamel paint and epoxy paint were used as binders. The prepared EM wave absorber's absorption properties were investigated. The prepared EM wave absorbers have 6 dB over in 2 GHz
${\sim}$ 4 GHz. We compared properties of wave absorption between paint-type and spray-type -
In this paper, we investigated EM wave absorption property of EM wave absorbers prepared with sendust. The EM wave absorbers have good EM wave absorption properties in 1 GHz
${\sim}$ 3 GHz. On the other hand, the absorption band of the EM wave absorber coated with$Al(OH)_3$ larger than non-coated one. Pulverization effect of sendust on EM wave absorption properties was also investigated. -
Recently, IMO(International Maritime Organization) have provided the recommendation of EMI and EMS for radio communication and equipments of marine from SOLAS convention at July 1st 2002. In this paper, we measured EMC environment on the HANBADA, which is Korea Maritime University training ship, and the 88KUMEO of a fishing boat for basic EMC environment of a ship. Measured Band is from 30 MHz to 2 GHz, polarization measurement is processed both vertical and horizontal polarization. We analysed the results in consideration of permissible criteria.
-
This paper presents an application of overlapping-grid technique for probe feeding simulation. The overlapping grid technique is used to solve contour path problem. In this technique, field interpolation is very important to make communication between two coordinates. By applying overlapping-grid technique, error of contour path in probe feeding simulation is reduced.
-
For under-water communication system, due to limit of bandwidth and reflect of under-water wave, it is difficult to implement high-reliability high-speed digital communication system. To apply high-reliability and high-speed communication system for under-water system, the efficient combine the channel design with the use of multiple transmit and/or receive antennas. Therefore this paper analyze the space time coded system for under-water communication environment.
-
In this paper we analyzed the performance of data transmission using BPSK modulation. The system performances were evaluated by the experiments in water tank. As a result we showed the influences of reverberation due to the multipath. In order to simplify the experiment procedure the channel coding etc. were omitted. The experimental result shows that the maximum transmission data rate in used water tank is about 350 bps at bit error rate of
$10^{-3}$ . -
선박 및 선박에 승선하고 있는 인명의 안전을 확보하기 위한 해상인명안전협약(SOLAS)은 전파통신기술 및 항해기술의 비약적인 발전을 반영하기 위하여 이미 2000년에 SOLAS 제V장에 대한 전면개정을 채택하여 여러 가지 항해설비에 대한 성능기준 개정 및 새로운 종류의 항해설비의 설치를 요구한 바 있으며, 그 이후 최근까지도 다양한 항해설비에 대한 여러 가지 새로운 사항들을 논의 중에 있다. 이 자료는 SOLAS에서 요구되는 항해설비와 관련한 국제해사기구(IMO)의 협약 제.개정 절차, 2000년 개정시 새로이 도입된 설비의 소개, IMO의 최근 결정사항 및 현재 논의되고 있는 사항들에 대한 정보를 제공하고자 작성되었다.
-
The effects of an urae injection at the exhaust pipe for a 4-cylinder DI(Direct Injection) diesel engine are investigated experimentally. The urea quantity was controlled by NOx quantity and MAF(Manifold Air Flow). The urea injection must be precisely metered and then I used the urea syringe pump. I have tested 4 kinds of items that were with the EGR base engine and without the EGR engine. Then I tested each urea-SCR(Selective Catalytic Reduction) system. As the results, I can caculate the SUF(Stoichiometric Urea Flow) and visualize the NOx results by variation of engine speed and engine load. Also, I can make the NOx map. Therfore, I knew that NOx reduction effects of the urea-SCR system without the EGR engine were better than the with EGR base engine except of low load and low speed.
-
This paper presents the study of flows at T-junction pipe with orifices. Experiments were carried out for several flow rates, orifice sizes, and pressure differences. Numerical simulations were also done to get more data for the wide range of flow rates. Experimental results and numerical ones are in a good agreement. Due to the effect of T-junction part, the flow rates at the lateral pipe are greater than those at straight pipe for the same pressure differences. When orifices were added, the effects of T-junction part on the ratio of flow rates and the ratio of loss coefficients reduced.
-
Particle image analyzer for measuring droplet size has been developed. Image processing technique was used with relaxation method. The morphological method based on partial curvature information of pre-processed images was adopted for recognition and separation of overlapped particles. The measurement results show that the present method may be reliable for the analysis of the size and distribution of droplets produced by water mist spay flow.
-
-
The human being continued the processing of improvement for well being life according to scientific results The other hand, All the seaman life take the rest and sleep in ship's office and living room. In this case, many crew took the pain of back spain or deposit the his fatigue, This will be decrease the productivity owing to crew's back spain or fatigue etc. In this study researched the problem of ship's bed mattress and the principle of Well being air mattress in technical standard etc. Specially decreased some kinds of bacillus, germ and many kinds of bacteria by using of tourmaline which emitted the far red light and negative ion from surface of the mattress. We developed and applied the ship's Well being air mattress to off shore and various kind of ship by International Labour Organization convention 192.
-
-
본 논문은 최근의 석유탐사 및 개발사업 현장에서 사용되고 있는 최신의 측량기술 및 해양공사의 측량 기술 표준화 동향을 소개하고, 이에 기반하여 동해1 가스전 해저배관 공사에 적용한 사례를 기술하였다. 해저배관 시설공사를 수행하기 위한 사전측량 및 시공지원 측량은 다양한 탐사장비가 동원되며, 각 장비들의 운영, 자료처리, 해석, 도면화를 위하여 실시간지원이 가능한 시스템을 운영하는 기술이 요구된다. 이를 위하여 해저배관 시공단계별(Pre-Installation Survey, Touch-down Monitoring, As-laid As-Built Survey, Post-installation Survey) 요구되는 측량성과 및 이를 획득하기 위한 소해측량 시스템의 성능평가 및 정확도 분석을 수행하였다. 또한, 해저지형 탐사를 위해 동원된 소해측량시스템(Swath Sonar System)에서 취득되는 수심(Bathymetry) 및 후방산란 음압(Backscattered Amplitude) 자료를 맵핑하여 해저배관의 설치 경로를 측량하는 기법에 대하여 소개하고, 추후 해저배관 보호 및 관리시의 효율적인 모니터링 기법을 제시한다.
-
A multi-channel seismic system has been developed and applied for bedrock mapping in near shore environment. The system is composed of an analog signal processor and an A/D converter installed on the computer, and a streamer with the group interval of 5 meters. The system is accomplished with a data acquisition program which controls the system and a data processing software. With the PC-based shallow marine seismic survey system high-resolution 2-D marine seismic profiles which have high S/N ratios can be obtained after appropriate data processing.
-
Cho, Kwon-Hae;Rhyu, Keel-Soo;So, Myung-Ok;Park, Jong-Il;Son, Min-Su;Ahn, Jong-Kap;Lee, Yun-Hyung;Jang, Tae-Lin 777
The importance of emergency diesel generator(EDG) has confirmed in the safety evaluation of PSA and the study on aging of EDG has been progressed actively as a part of the project of nuclear plant aging research in the U.S.A. As the result, the concept of performance evaluation is being transferred from statistical analysis of test results to performance monitoring and trending analysis for monitoring of aging and reliability. Recently, the study related aging characteristic and reliability for EDGS has begun in Korea. Consequently, the efficient performance monitoring based systematic and integrated monitoring and failure diagnostic technology is necessary. In the research, the knowledge basis of monitoring parameters for EDGS is constructed, and the prototype monitoring and diagnosis system applicable to Pielstick EDG is developed. -
This document provides the concerning information of the MEPC Committee and DE sub-Committee of International Maritime Organization in accordance with enforcement of an International Air Pollution Prevention Certificate at May 19 2005years.
-
An overview of 30 feet sailing yacht design is presented, with an emphasis on the factors contributing to start-up popularization. After prescribing the configurations of the purposed yacht, the design of the hull form with a rudder and a keel, are schematically described. Also the determinations of the dimensions of the sail and rig are performed.
-
A model test was carried out, in order to verify the hydrodynamic performances of public 30 feet class sailing yacht. In the initial design stage, the performances and the running attitude of sail yacht including the hull form and sail plan, appendages were estimated by VPP, from which made the representative test conditions. A new experiment system such as captive model device was composed because the running attitude could be changed by wind conditions. The test results show that the minimum resistance is generated in the heeling 20 degree, which was expected in the initial design stage. It is thought to be the useful informations that the keel has an effects on hydrodynamic forces and resistance differences between the upwind and the downwind condition. Also this paper is associated with the state-of-the-art of calculating sailing yacht performance as this is performed in velocity prediction program (VPP). The VPP results shows a typical shape of a sailing yacht and the designed yacht has the best performance at 120 degree angle of true wind with 20 knots.
-
It is important to understandflow characteristics and performances of sailsfor both sailors and designers who want to have efficient thrust of yacht. In this paper the viscous flows around sail-like rigid wings, which are similar to main and jib sails of a 30 feet sloop, are calculated using a CFD tool. Lift, drag and thrust forces are estimatedfor various conditions of gap distance between the two sails and the center of effort of the sail system is obtained. Wind tunnel experiments are also carried out to measure aerodynamic forces acting on the sail system and to validate the computation. It is found that the combination of two sails produces the lift force larger than the sum of that produced separately by each sail and the gap distance between the two sails is an important factor to determine total lift and thrust.
-
RIB(Rigid Inflatable Boat)형 보트는 선체, 팽차식 선측튜브를 적용한 고속 다목적보트로 뛰어난 내항성능과 높은 안전성으로 해외 선진국에서는 해양레저 활동에 적합한 신개념 고부가가치 보트로 각광받고 있으나 국내에는 레저용 RIB 보트의 제작 및 개술개발 실적이 전무한 실정이다. 이에 본 연구에서는 고속이면서도 안정성 및 편의성을 고려한 레저용 RIB의 최적선형 설계 및 공간배치 연구, 하이파론 선측튜브 설계, 조선학적 제계산을 통한 주요성능 검토 등을 통하여 최근 급증하고 있는 해양레저 수요에 대응한 6m급 RIB형 레저보트를 개발하고자 하였다.
-
This study aims to provide divers with improved safe diving practices by analyzing reports on scuba diving casualties that recently occured in Korea, Japan and USA. The result of this study should be notified to all the divers in Korea for the purpose of preventing the diving accident. All the data were collected through the diving accident reports of various sourses, which include KUA(Korea Underwater Association) technical committee, the accident statistical data of National Maritime Police Agency, articles of domestic and foreign scuba diving magazine, accident reports of various newspaper, annual report on decompression illness and diving fatalities by DAN(Diver Alert Network), various type of data on diving accident from local as well as national seminars, and medical treatment data of diving accident.
-
In recent years, the LNGC fleet is expanded unprecedentedly. Ship's owners and shipbuilders are focusing on technology and reliability of new propulsion system from economical, environmental and safety angles. This paper give describes the new trend of propulsion system and boil off gas handling system from LNG carriers.
-
In this paper, it is presented a frequency modulated continuous wave radar (FMCW) for distance measurement. The frequency range is
$10{\sim}11$ GHz and the sweep time of the signal is 100 ms. The test target is 0.8 m2 of metal plate. The experiment is performed in open ground and the pyramidal horn antenna of about 22 dBi gain is used. The beat frequency according to the target moving to 40 m is measured. There is a good agreement between measured and calculated results. But the resolution of the FMCW radar is not good such as about 10 cm. It is result from the nonlinear signal of voltage controlled oscillator (VCO). To improve the nonlinear characteristic of VCO, a high pass filter and phase locked loop (PLL) frequency synthesizer are included in the radar system. -
Fully digital controlled 20-bit magnet power supplies have been developed and successfully tested for closed orbit correction of PLS(Pohang Light Source). The new digital power supply has used fiber optics for 25kHz switching of IGBT drivers, and implemented DSP, ADC, Interlock, DCCT cards in a compact 3U-sized 19" chassis. Input/Output low-pass filters suppress harmonics of 60Hz line frequency and switching frequency noise effectively. Overall performance of the power supplies have been demonstrated as +/- 2ppm short-term stability(<1 min), and +/- 10ppm long-term stability(<36 hours). All the existing 12-bit 70 power supplies for vertical correction magnets will be replaced with new digital power supplies during 2005 summer shutdown period. In this paper, we will describe the hardware structure and control method of the digital power supply and the experimental results will be shown.
-
A piezoresistive pressure sensor using a silicone rubber membrane has been fabricated on the selectively diffused (100)-oriented n/n+/n silicon substrates by a unique silicon micromachining technique using porous silicon ething. The width, length and thickness of the beam were 120
${\mu}m$ , 600${\mu}m$ and 7${\mu}m$ , respectively and the thickness of the silicone rubber membrane was 40${\mu}m$ . By the fusion of silicon beam and silicone rubber membrane, the mechanical strength of the pressure sensor could be highly improved due to smaller shear stress. The effectiveness of the sensor was confirmed through an experiment and FEM simulation in which the pressure sensor was characterized. -
This paper is presented the analysis results and simulation results of cascaded H-bridge 7 level inverter with various modulation index. Stepped waveform having number of switching was used to eliminate harmonic components. Switching angles according to modulation index are calculated numerically. Therefore, 3 times of switching with 7 level topology and QWS(Quarter Wave Symmetry) could eliminate 5th and 7th harmonics. The harmonic characteristics are compared to those of space vector modulation method which known as common modulation method in industrial field. Stepped waveform method showed higher ability to reduce, especially lower order of harmonics.
-
함정의 추진시스템은 기계식에서 에너지 효율이 높고, 구성 장비의 수가 줄어들며 유지 보수 특성이 향상되는 전기식으로 연구 개발되어지고 있는 추세이다. 따라서 본 논문에서는 함정의 전기추진시스템의 장점과 현재 개발중인 전기추진 함정의 기술과 발전 경향을 분석 조사하였다.
-
This paper deals with the design rule and performance results of the surge protective devices (SPDs) for low-voltage mains on shipboard. The proposed SPDs consists of a metal oxide varistors (MOV) and a L-C filter to improve noise-elimination performance. Three kinds of SPDs are fabricated and tested by using a combination surge generator which produce the standard impulse current of 8/20
${\mu}s$ 2.1kA. As a results, the proposed SPDs with series L-C filter have more excellent transient blocking and noise reduction performance than the conventional ones. -
This paper describes a system for LNG carrier's loading and discharging work education. This system consists of three modules(cargo work simulation, ballast work simulation and loading calculation module), and could be a useful to train mariners boarding on LNG carrier so as to take a suitable action while their ship maneuvering and cargo handling.
-
-
Cho, Kwon-Hae;Park, Go-Ryong;Lee, Dong-Hun;Kim, In-Suk;Lee, Sung-Gwan;Jang, Tae-Lin;Moon, Byung-Jin;Son, Min-Su 1069
The oil crises in 1973 and 1979 caused considerable effort to decrease the fuel consumption. As a result, the main engine had been changed through the shape(from loop scavenging air system to uniflow scavenging air system), higher compression ratio, low speed and long stroke. It is difficult to make a various engine satisfied with all owner's request. So manufacturer could find a way that can change the rating through large range from the engine already manufactured. These ways are tried through large range to change rpm to 72% and engine's output to 48% of MCR with keeping the normal engine's shape almost. The important element considered in the process of derated output of the main engine is to recover the beginning overcapitalization as soon as possible through low SFOC. In this paper, it is compared and considered between rating and derating engine with several data about modifying rating which have been done by engine manufacturer so far. And the selection process of derating engine is studied also. -
It's important that the measurement of ship's draft, cargo tank level & volume is relative to ship's stability and fee. In this paper, the corrected level and volume technique is introduced.
-
Repeated ribs are used on heat exchange surfaces to promote turbulence and enhance convective heat transfer. Applications include fuel rods of gas-cooled nuclear reactors, inside cavities of turbine blades, and internal surfaces pipes used in heat exchangers. Despite the great number of literature papers, only few experimental data concern detailed distributions of friction factors and heat transfer coefficients in square channels varying the number of rough walls. This issue is tackled by investigating effects of different number of ribbed walls on heat transfer and friction characteristics in square channel. The rough wall have a 45
$^{\circ}$ inclined square rib. Uniform heat flux is maintained on whole inner heat transfer channel area. The heat transfer coefficient and friction factor values increase with increasing the number of rough walls. -
This study is performed to develop a tripple-tube exchanger which can improve the system efficiency. Three different tube diameters are compacted by one body(tripple-tube) to recover waste heat from heat exchanging among the fluids. With this, the tripple-tube shows higher cooling capacity than the double-tube after comparing between those two systems. The results of this study are basic data to design the optimum tripple-tube heat exchanger.
-
In this study, the experiment of thermal performance about closed-type hybrid cooling tower was conducted. A closed type cooling tower is a device similar to a general cooling tower, but with cooling tower replaced by a heat exchanger. The test section for this experiment has the process that the cooling water flows from top part of heat exchanger to bottom side in the inner side of tube, and spray water flows gravitational direction in the outer side of it. Air contacts of tube outer side are counterflow. The heat transfer pipe used in this experiment is a bare type tube having an outside diameter of 15.88mm. In this experiment, heat performances of the cooling tower are calculated such as overall heat transfer coefficient of between the process fluid and air, cooing capacity and pressure drop.
-
The analysis of the thermal boundary resistance is very important in the both cases of microscale and macroscale systems because it plays a role of thermal barrier against a heat flow. Especially, since fairly large heat energy is generated in microscale or nanoscale systems with electronic chips, the thermal boundary resistance is a key factor to guarantee the performance of those devices. In this study, the transfer of the oscillator's motion information with 2 degrees of freedom is investigated for clarifying the mechanism of a thermal boundary resistance. We found that the transfer of the oscillator's motion information is defined as a cross-correlation coefficient and the magnitude of it determines the temperature jump over a solid interface. That is, the temperature jump over an interface increases as the magnitude of a cross-correlation coefficient decreases and vice versa.
-
Oh, Jin-Seok;Lim, Kyu-Myung;Jin, Sun-Ho;Kwak, Jun-Ho;Jo, Kwan-Jun;Yu, Byung-Rang;Bae, Byung-Deok 1108
Recently, the fuel charge is accounted for very high in the navigation cost. Therefore Shipowner is tried to find method for reducing oil consumption. ERCS(Energy Reduced Cooling System) is one of the method. The ERCS algorithm operates to decrease a power consumption of main sea water cooling pump through inverter control. We have developed ERCS controller with algorithm. The ERCS controller consists of CPU board, Digital I/O board, A/D board, D/A board and LCD/SW board. We tested with dummy signal to confirm the algorithm working correctly and achieved the good results. Before soon we will test under real condition in the ship and expect to get the result as forecasted. -
Yu, Byong-Rang;Oh, Jin-Seok;Jin, Sun-Ho;Lim, Myoung-Kyu;Kwak, Jun-Ho;Jo, Kwan-Jun;Kim, Jang-Mok 1113
The power electric system is one of the most concerning factor for the reliability of the electric propulsion ship. operation in higher temperature decreases the device's reliability and power efficiency. the management of power loss and temperature of switching devices is indispensable for the reliability fo the power electric system. In this paper, IGBT chip of the switching devices is modeled and MIIR(Motor with Inverter Internal to Rotor)type of the propulsion motors is used. these parts interact with each other to calculate the loss and temperature of device. calculated Results is modeled and designed of the control and monitoring system for the electric propulsion system. -
Experimental results for heat transfer characteristic and pressure gradient of HCs refrigerants R-290, R-600a, R-1270 and HCFC refrigerant R-22 during condensing inside horizontal double pipe heat exchangers are presented. The test sections which have one tube diameter of 12.70 mm with 0.86 mm wall thickness, another tube diameter of 9.52 mm with 0.76 mm wall thickness are used for this investigation. The local condensing heat transfer coefficients of hydrocarbon refrigerants were higher than those of R-22. The average condensing heat transfer coefficient increased with the increase of the mass flux. It showed the higher values in hydrocarbon refrigerants than R-22. Hydrocarbon refrigerants have higher pressure drop than those of R-22 in 12.7 mm and 9.52 mm. This results from the investigation can be used in the design of heat transfer exchangers using hydrocarbons as the refrigerant for the air-conditioning systems.
-
The finite difference lattice Boltzmann method(FDLBM) is a quite recent approach for simulating fluid flow, which has been proven as a valid and efficient tool in a variety of complex flow problems. It is considered an attractive alternative to conventional FDM and FVM, because it recovers the Navier-Stokes equations and is computationally more stable, and easily parallelizable to simulate for various laminar flows and a direct simulation of aerodynamics sounds. However, the research of a numerical simulation of turbulent flow by FDLBM, which is important to analyze the structure of turbulent flow in engineering fields, is not carried out. In this research, the FDLBM built in the turbulent model is applied, and a flowfield around 2-dimensional square to validate the applied model with 2D9V is simulated. Besides, 2D computation of the cavity noise generated by flow over a cavity at a Mach number of 0.1 and a Reynolds number based on cavity depth of 5000 is calculated. The computation result is well presented a understanding of the physical phenomenon of tonal noise occurred primarily by well-jet shear layer and vortex shedding and an aeroacoustic feedback loop.
-
In order to evaluate the safety of navigation at sea and the safety of mooring ship on berthing, it is necessary that the wave and wind induced ship dynamic motion should be measured in real time domain for the validity of theoretical evaluation method such as sea-keeping performance and safety of mooring. In this paper, the basic design of sensors is discussed and some system configurations were shown. The developed system mainly consists of 4 kinds of sensors such as three dimensional accelerator, two dimensional tilt sensor, two displacement sensors and azimuth sensor. Using the this measuring system, it can be obtained the 6 degrees of freedom of ship dynamic motions at sea and on berthing such as rolling, pitching, yawing, sway, heave, surge under the external forces.
-
Due to the miniaturization of electrical components and assembles on signal circuits, transient overvoltages caused by switching operation or lightning surges have become more interesting concern to the field of electrical engineering. In this paper, the development of surge protective devices(SPDs) that can protect sensitive signal device on shipboard from overvoltages are described. Two kinds of SPDs are designed and tested by using a combination surge generator which can produce the standard impulse current of 8/20
${\mu}s$ 2.1kA according to the IEC 61000-4-5 standard. From the simulation and experimental results, it is confirmed that the proposed SPDs have an enough protection performance with a low insertion loss and a low clamping voltage. -
This paper describes a new transient voltage suppressor(TVS) with a low insertion loss and a high cut-off frequency to protect antenna circuit from transient voltages. Conventional protection devices have some problems such as a low frequency bandwidth and a high insertion loss. In order to improve these limitations, a coaxal type TVS, which consists of a gas tube is developed. The performance of the proposed transient voltage suppressor is tested by using a combination surge generator specified in IEC 61000-4-5 standard and by using a network analyzer of 40 MHz
${\sim}$ 5 GHz bandwidth. From the experimental results, it is confirmed that the proposed TVS has an enough protection performance in a low insertion loss and a high cut-off frequency. -
Oh, Jin-Seok;Jo, Kwan-Jun;Kwak, Jun-Ho;Jin, Sun-Ho;Yu, Byong-Rang;Lim, Myoung-Kyu;Lee, Hong-Chan 1170
This paper is analyzed the characteristic of multi-phase inverter for the electric propulsion system. Two BLDC motors with 3 and 7 phases are designed with these features in order to simulate the effect of increasing the number of phases. From the simulation results, the 7-phase given better performance in terms of torque pulsation. Also, the torque pulsation can be reduced further by increasing the number of phases. -
A linear power amplifier is particularly emphasized on the system using a linear modulations, such as 16QAM and QPSK with pulse shaping, because intermodulation distortion which causes adjacent channel interference and co-channel interference is mostly generated in a nonlinear power amplifier. In this paper, parameters of a linearization loop, such as an amplitude imbalance, a phase imbalance and a delay mismatch, are briefly analyzed to get a specific cancellation performance and linearization bandwidth. Experimental results are presented for IMT-2000 frequency band. The center frequency of the feedforward amplifier is 2140 MHz with 60 MHz bandwidth. When the average output power of feedforward amplifier is 20 Watt, the intermodulation cancellation performance is more than 21 dB. In this case, the output power of feedforward amplifier reduced 3.5 dB because of extra delay line loss and coupling loss. The feedforward amplifier efficiency is more than 7.2 % for multicarrier signals, 59 dBc for ACPR.