• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.10a
• /
• pp.713-716
• /
• 2013

The device performances of N-channel Tunneling FET have been characterized with different intrinsic length between drain and gate($L_{in}$), drain and source doping, permittivity and oxide thickness when the total effective channel length is constant. N-channel Tunneling FET of SOI structure have been used in characterization. $L_{in}$ was from 30nm to 70nm, dose concentration of drain and source were from $2{\times}10^{12}cm^{-2}$ to $2{\times}10^{15}cm^{-2}$ and from $1{\times}10^{14}cm^{-2}$ to $3{\times}10^{15}cm^{-2}$, permittivity was from 3.9 to 29, and oxide thickness was from 3nm to 9nm. The device performances were characterized by Subthreshold slope(S-slope), On/off ratio, and leakage current. From the simulation results, the leakage current have been reduced for long $L_{in}$ and low drain doping. S-slope have been reduced for high source doping, high permittivity and thin oxide thickness. With considering the leakage current and S-slope, it is desirable that are long $L_{in}$, low drain doping, high source doping, high permittivity and thin oxide thickness to optimize device performance in n-channel Tunneling FET.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.2
• /
• pp.77-79
• /
• 1992

We propose a self-aligned and double recessed technique for GaAs power MESFETs application. The gate length and the wide recess width are defined by a selective removal of the SiN layer using reactive ion etching(RIE) while the depth of the channel is defined by chemical etching of GaAs layers. The threshold voltages and the saturation drain voltage could be sucessfully controlled using this technique. The lateral-etched distance increases with the dry etching time and the source-drain breakdown voltage of MESFET increases up to about 30V at a pinch-off condition. The electrical characteristics of a MESFET with a gate length of 2 x10S0-6Tm and a source-gate spacing of 33 x10S0-6Tm show maximum transconductance of 120 mS/mm and saturation drain current density of 170-190mA/mm at a gate voltage of 0.8V.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.112-120
• /
• 1996

With the MOsES (mask oxide sidewall etch scheme)process which uses the conventional i-line stepper and isotropic wet etching, CMOSFET's with fine gate pattern of 0.1.mu.m CMOSFET device, the screening oxide is deposited before the low energy ion implantation for source/drain extensions and two step sidewall scheme is adopted. Through the characterization of 0.1.mu.m CMOSFET device, it is found that the screening oxide deposition sheme has larger capability of suppressing the short channel effects than two step sidewall schem. In cse of 200.angs.-thick screening oxide deposition, both NMOSFET and PMOSFET maintain good subthreshold characteristics down to 0.1.mu.m effective channel lengths, and show affordable drain saturation current reduction and low impact ionization rates.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.97-98
• /
• 2006

High current behaviors of the grounded gate extended drain N-type metal-oxide-semiconductor field effects transistor (GG_EDNMOS) electro-static discharge (ESD) protection devices are analyzed. Simulation based contour analyses reveal that combination of BJT operation and deep electron channeling induced by high electron injection gives rise to the 2-nd on-state. Thus, the deep electron channel formation needs to be prevented in order to realize stable and robust ESD protection performance. Based on our analyses, general methodology to avoid the double snapback and to realize stable ESD protection is to be discussed.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.918-921
• /
• 1999

The breakdown voltage in fully depleted SOI N-MOSFET’s have been studied over a wide range of film thicknesses, channel doping, and channel lengths. An asynmmetric Source/Drain SOI technology is proposed, which having the advantages of Normal LDD SOI(Silicon-On-Insulator) for breakdown voltage and gives a high drivability of LDD SOI without sacrificings hot carrier immunity The two-dimensional simulations have been used to investigate the breakdown behavior in these device. It is found that the breakdown voltage(BVds) is almost same with high current drivability as that in Normal LDD SOI device structure.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.8
• /
• pp.8-21
• /
• 1997

In this paper, we consider resistive shorts on gate-source, gate-drain, and drain-source as well as opens in MOS FETs included in typical memory cell of VLSI SRAM and analyze behavior of memory by using PSPICE simulation. Using conventional fault models and this behavioral analysis, we propose linear testing algorithm of complexity O(N) which can be applied to both functional testing and IDDQ (quiescent power supply current) testing simultaneously to improve functionality and reliability of memory. Finally, we implement BIST (built-in self tsst) circuit and BICS(built-in current sensor), which are embedded on memory chip, to carry out functional testing efficiently and to detect various defects at high-speed respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.443-443
• /
• 2012

We fabricated a-IGZO TFT with AZO/Ag/AZO transparent multilayer source/drain contacts by rf magnetron sputtering. Enhanced electrical device performance of a-IGZO TFT with AZO/Ag/AZO multilayer S/D electrodes (W/L = = 400/50 mm) was achieved with a subs-threshold swing of 3.78 V/dec, a minimum off-current of 10-12 A, a threshold voltage of 1.80 V, a field effect mobility of 10.86 cm2/Vs, and an on/off ration of 9x109. It demonstrated the potential application of the AZO/Ag/AZO film as a promising S/D contact material for the fabrication of the high performance TFTs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.9
• /
• pp.793-799
• /
• 2006

In this paper, the gate leakage current is first calculated using the experimental method between gate and drain by opening source electrode. the gate to drain current has been obtained with ground source. The difference between two currents has been tested and proves that the electric field generated by channel charge effect against the image force lowering.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.6
• /
• pp.462-465
• /
• 2009

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method, The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than 10), Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• Journal of information and communication convergence engineering
• /
• v.7 no.3
• /
• pp.361-365
• /
• 2009

This paper has been presented the transport characteristics of FinFET using the analytical potential model based on the Poisson's equation in subthreshold and threshold region. The threshold voltage is the most important factor of device design since threshold voltage decides ON/OFF of transistor. We have investigated the variations of threshold voltage and drain induced barrier lowing according to the variation of geometry such as the length, width and thickness of channel. The analytical potential model derived from the three dimensional Poisson's equation has been used since the channel electrostatics under threshold and subthreshold region is governed by the Poisson's equation. The appropriate boundary conditions for source/drain and gates has been also used to solve analytically the three dimensional Poisson's equation. Since the model is validated by comparing with the three dimensional numerical simulation, the subthreshold current is derived from this potential model. The threshold voltage is obtained from calculating the front gate bias when the drain current is $10^{-6}A$.