• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.10
• /
• pp.877-882
• /
• 2005

In order to fabricate a high breakdown SiC-SBD (Schottky barrier diode), we investigate an effect on metal guard ring (MGR) in breakdown characteristics of the SiC-SBD. The breakdown characteristics of MGR-type SiC-SBD is significantly dependent on both the guard ring metal and the alloying time of guard ring metal. The breakdown characteristics of MGR-type SiC-SBDs are essentially improved as the alloying time of guard ring metal is increased. The SiC-SBD without MGR shows less than 200 V breakdown voltage, while the SiC-SBD with Al MGR shows approximately 700 V breakdown voltage. The improvement in breakdown characteristics is attributed to the field edge termination effect by the MGR, which is similar to an implanted guard ring-type SiC-SBD. There are two breakdown origins in the MGR-type SiC-SBD. One is due to a crystal defects, such as micropipes and stacking faults, in the Epi-layers and the SiC substrate, and occurs at a lower electric field. The other is due to the destruction of guard ring metal, which occurs at a higher electric field. The demolition of guard ring metal is due to the electric field concentration at an edge of Schottky contact metal.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.27-30
• /
• 2015

SiC based Schottky barrier diodes were prepared by using the facing targets sputtering method. In this research, 4H-SiC polytypes of SiC were adopted and Molybdenum, Titanium was employed as the Schottky metal of the metal-semiconductor contacts. Both structures showed the rectifying nature in their forward and reverse J-V characteristic curve and the ideality factors calculated from these plots that were close to unity were represented the nearly ideal behavior. Difference of Schottky barrier height between prepared devices was also corresponding with the electrical characteristics of themselves. Therefore the suitability of the facing targets sputtering method for fabrication of Schottky diodes could be suggested from these results.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.1
• /
• pp.7-15
• /
• 2015

We have investigated electrical properties of graphene/Ge Schottky barrier diode (SBD) fabricated on Ge film epitaxially grown on Si substrate. When decreasing temperature, barrier height decreased and ideality factor increased, implying their strong temperature dependency. From the conventional Richardson plot, Richardson constant was much less than the theoretical value for n-type Ge. Assuming Gaussian distribution of Schottky barrier height with mean Schottky barrier height and standard deviation, Richardson constant extracted from the modified Richardson plot was comparable to the theoretical value for n-type Ge. Thus, the abnormal temperature dependent Schottky behavior of graphene/Ge SBD could be associated with a considerable deviation from the ideal thermionic emission caused by Schottky barrier inhomogeneities.

• Korean Journal of Materials Research
• /
• v.31 no.2
• /
• pp.97-100
• /
• 2021

We report the effect of Standard Clean-1 (SC-1) cleaning to remove residual Ti layers after silicidation to prevent Al diffusion into Si wafer for Ti Schottky barrier diodes (Ti-SBD). Regardless of SC-1 cleaning, the presence of oxygen atoms is confirmed by Auger electron spectroscopy (AES) depth profile analysis between Al and Ti-silicide layers. Al atoms at the interface of Ti-silicide and Si wafer are detected, when the SC-1 cleaning is not conducted after rapid thermal annealing. On the other hand, Al atoms are not found at the interface of Ti-SBD after executing SC-1 cleaning. Al diffusion into the interface between Ti-silicide and Si wafer may be caused by thermal stress at the Ti-silicide layer. The difference of the thermal expansion coefficients of Ti and Ti-silicide gives rise to thermal stress at the interface during the Al layer deposition and sintering processes. Although a longer sintering time is conducted for Ti-SBD, the Al atoms do not diffuse into the surface of the Si wafer. Therefore, the removal of the Ti layer by the SC-1 cleaning can prevent Al diffusion for Ti-SBD.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.123-126
• /
• 2022

We investigated deep levels in n-type 4H-SiC epitaxy layer of the Positive-Intrinsic-Negative diode and Schottky barrier diodes by using deep level transient spectroscopy. Despite the excellent performance of 4H-SiC, research on various deep level defects still requires a lot of research to improve device performance. In Positive-Intrinsic-Negative diode, two defects of 196K and 628K are observed more than Schottky barrier diode. This is related to the action of impurity atoms infiltrating or occupying the 4H-SiC lattice in the ion implantation process. The I-V characteristics of the Positive-Intrinsic-Negative diode shows about ~100 times lower the leakage current level than Schottky barrier diode due to the grid structures in Positive-Intrinsic-Negative. As a result of comparing the capacitance of devices diode and Schottky barrier diode devices, it can be seen that the capacitance value lowered if it exists the P implantation regions from C-V characteristics.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.68-71
• /
• 2021

In this paper, GaN-SBD devices with excellent breakdown voltage and frequency characteristics for use in high-power microwave wireless power transmission has been modeled for PSpice circuit simulation. The RF-DC conversion circuits were simulated and compared with a commercial Si-SBD device. Although the modeled GaN-SBD devices had lower RF-DC conversion efficiency compared to Si-SBD at 2.4 and 5.8 GHz, it was confirmed through PSpice circuit simulations that they can be used sufficiently according to the required application circuit in a high power situation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.30-33
• /
• 1999

본 연구에서는 Pt/f4-SiC Schottky barrier diodes(SBDs)의 소자 성능향상과 미세구조와의 상관관계를 규명하였다. 다른 열처리 온도구간에 따른 금속/SiC 계면의 미세구조 평가는 X-ray scattering법을 사용하여 분석하였다. 소자의 역 방향 특성은 열처리 온도가 증가함에 따라 저하되었다. As-deposited와 $850^{\circ}C$ 온도에서 열처리된 소자의 최대 항복전압은 각각 1300 V와 626 V 이었다. 그러나, 소자의 순방향 특성은 열처리 온도가 증가함에 따라 향상되었다. X-ray scattering법으로 >$650^{\circ}C$ 이상의 열처리 온도에서는 Pt/SiC 계면에서 Pt-silicides가 형성되었고, 이러한 Silicides의 형성이 Pt/SiC 계면의 평활도를 증가시킨 원인이 됨을 보였다. SBDs의 순방향 특성은 열처리 과정동안 Pt/SiC 계면에서 형성된 silicides의 결정성에 강하게 의존함을 알 수 있었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.640-644
• /
• 1998

We have fabricated Sb/SiC(4H) Schottky barrier diode (SBD) of which characteristics compared with that of Ti/SiC(4H) SBD. The donor concentration of the n-type SiC(4H) obtained by capacitance-voltage (C-V) measurement was about $2.5{\times}10 ^{17}{\textrm}cm^{-3}$. The ideality factors of 1.31 was obtained from the slope of forward current-voltage (I-V) characteristics of Sb/SiC(4H) SBD at low current density. The breakdown field of Sb/SiC(4H) SBD under the reverse bias voltage was about $4.4{\times}10^2V$/cm. The built-in potential and the Schottky barrier height (SBH) of Sb/SiC(4H) SBD were 1.70V and 1.82V, respectively, which were determined by the analysis of C-V characteristics. The Sb/SiC(4H) SBH of 1.82V was higher than Ti/SiC(4H) SBH of 0.91V. However, the current density and reverse breakdown field of Sb/SiC(4H) were low as compared with those of Ti/SiC(4H). The Sb/SiC(4H), as well as the Ti/SiC(4H), can be utilized as the Shottky barrier contact for the high-power electronic device.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.367-371
• /
• 2018

1,200 V class junction barrier schottky (JBS) diodes and schottky barrier diodes (SBD) were simultaneously fabricated on the same 4H-SiC wafer. The resulting diodes were characterized at temperatures from room temperature to 473 K and subsequently compared in terms of their respective I-V characteristics. The parameters deduced from the observed I-V measurements, including ideality factor and series resistance, indicate that, as the temperature increases, the threshold voltage decreases whereas the ideality factor and barrier height increase. As JBS diodes have both Schottky and PN junction structures, the proper depletion layer thickness, $R_{on}$, and electron mobility values must be determined in order to produce diodes with an effective barrier height. The comparison results showed that the JBS diodes exhibit a larger effective barrier height compared to the SBDs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.29-34
• /
• 2008

In this paper, we investigated electrical and physical characteristics of nickel silicide using rare-earth metals(Er, Yb, Tb, Dy), Incorporated Ytterbium into Ni-silicide is proposed to reduce work function of Ni-silicide for nickel silicided schottky barrier diode (Ni-silicided SBD). Nickel silicide makes ohmic-contact or low schottky barrier height with p-type silicon because of similar work function (${\phi}_M$) in comparison with p-type silicon. However, high schottky barrier height is formed between Ni-silicide and p-type substrate by depositing thin ytterbium layer prior to Ni deposition. Even though the ytterbium is deposited below nickel, ternary phase $Yb_xN_{1-x}iSi$ is formed at the top and inner region of Ni-silicide, which is believed to result in reduction of work function about 0.15 - 0.38 eV.