• ETRI Journal
• /
• v.20 no.2
• /
• pp.241-249
• /
• 1998

The structure and electrical characteristics of metal-ferroelectric-semiconductor FET(MFSFET) for a single transistor memory are presented. The MFSFET was comprised of polysilicon islands as source/drain electrodes and $BaMgF_4$ film as a gate dielectric. The polysilicon source and drain were built-up prior to the formation of the ferroelectric film to suppress a degradation of the film due to high thermal cycles. From the MFS capacitor, the remnant polarization and coercive field were measured to be about $0.6{\mu}C/cm^2$ and 100 kV/cm, respectively. The fabricated MFSFETs also showed good hysteretic I-V curves, while the current levels disperse probably due to film cracking or bad adhesion between the film and the Al electrode.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1463-1465
• /
• 1994

The electrical characteristics of $Al/Ta_2O_5/Si$ metal-oxide-semiconductor (MOS) capacitors were studied. $Ta_2O_5$ films on p-type silicon had been prepared by ionized cluster beam epitaxy technique (ICBE). This $Ta_2O_5$ films have low leakage current, high breakdown strength and low flat band shift. In this research, a single crystalline cpitaxial film of $Ta_2O_5$ has been grown on p-Si wafer using an ICBE technique. The native oxide layer ($SiO_2$) on the silicon substrate was removed below $500^{\circ}C$ by use of an accelerated arsenic ion beam, instead of a high temperature deposition. $Ta_2O_5$ films formed by ICBE technique can be received considerable attention for applications to coupling capacitors, gate dielectrics in MOS devices, and memory storage capacitor insulator because of their high dielectric constants above 20 and low temperature process.

• Journal of the Korean Vacuum Society
• /
• v.19 no.1
• /
• pp.14-21
• /
• 2010

Ge is one of the attractive channel materials for the next generation high speed metal oxide semiconductor field effect transistors (MOSFETs) due to its higher carrier mobility than Si. But the absence of a chemically stable thermal oxide has been the main obstacle hindering the use of Ge channels in MOS devices. Especially, the fabrication of gate oxide on Ge with high quality interface is essential requirement. In this study, $HfO_xN_y$ thin films were prepared by plasma-enhanced atomic layer deposition on Ge substrate. The nitrogen was incorporated in situ during PE-ALD by using the mixture of nitrogen and oxygen plasma as a reactant. The effects of nitrogen to oxygen gas ratio were studied focusing on the improvements on the electrical and interface properties. When the nitrogen to oxygen gas flow ratio was 1, we obtained good quality with 10% EOT reduction. Additional analysis techniques including X-ray photoemission spectroscopy and high resolution transmission electron microscopy were used for chemical and microstructural analysis.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.6 s.348
• /
• pp.53-61
• /
• 2006

In high speed flash type or pipelining type A/D Converter, the faster sampling frequency is, the more the effect of DC reference fluctuation is increased by clock feed-through and kick-back. When we measure A/D Converter, further, external noise increases reference voltage fluctuation. Thus reference fluctuation reduction circuit must be needed in high speed A/D converter. Conventional circuit simply uses capacitor but layout area is large and it's not efficient. In this paper, a reference fluctuation reduction circuit using transmission gate is proposed. In order to verify the proposed technique, we designed and manufactured 6bit 2GSPS CMOS A/D converter. The A/D converter is based on 0.18um 1-poly 5-metal N-well CMOS technology, and it consumes 145mW at 1.8V power supply. It occupies chip area of $977um\times1040um$. Experimental result shows that SNDR is 36.25 dB and INL/DNL ${\pm}0.5LSB$ when sampling frequency is 2GHz.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.364-370
• /
• 2014

In this paper, high reliable trench formation technique and a novel fabrication techniques for trench gate MOSFET is proposed which is a key to expend application of power MOSFET in the future. Trench structure has been employed device to improve Ron characteristics by shrinkage cell pitch size in DMOSFET and to isolate power device part from another CMOS device part in some power integrated circuit. A new process method for fabricating very high density trench MOSFETs using mask layers with oxide spacers and self-align technique is realized. This technique reduces the process steps, trench width and source and p=body region with a resulting increase in cell density and current driving capability and decrease in on resistance.

• Journal of information and communication convergence engineering
• /
• v.13 no.4
• /
• pp.257-263
• /
• 2015

In this study, organic field-effect transistors (OFETs) using a copper phthalocyanine (CuPc) material as an active layer and SiO₂ as a gate insulator were fabricated with varying active layer thicknesses and channel lengths. Further, using a thermal evaporation method in a high-vacuum system, we fabricated a CuPc FET device of the top-contact type and used Au materials for the source and drain electrodes. In order to discuss the channel formation and FET characteristics, we observed the typical current-voltage characteristics and calculated the threshold voltage of the CuPc FET device. We also found that the capacitance reached approximately 97 pF at a negative applied voltage and increased upon the accumulation of carriers at the interface of the metal and the CuPc material. We observed the typical behavior of a FET when used as an n-channel FET. Moreover, we calculated the threshold voltage to be about 15-20 V at V_DS = -80 V.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.11
• /
• pp.981-987
• /
• 2014

DC/DC switching power converters are commonly used to generate a regulated DC output voltage with high efficiency. The DC/DC converter is composed of a MOSFET (metal-oxide semiconductor field effect transistor), a PWM-IC (pulse width modulation-integrated circuit) controller, inductor, capacitor, etc. It is shown that the variation of threshold voltage and the breakdown voltage in the electrical characteristics of MOSFET occurs by radiation effects in TID (Total Ionizing Dose) testing at the low energy ${\gamma}$ rays using $^{60}Co$, and 5 heavy ions make the gate of MOSFET broken in SEGR (Single Event Gate Rupture) testing. TID testing on MOSFET is accomplished up to the total dose of 40 krad, and the cross section($cm^2$) versus LET(MeV/mg/$cm^2$) in the MOSFET operation is studied at SEGR testing after implementation of the controller board.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.289.2-289.2
• /
• 2016

In-Ga-Zn-O(IGZO) receive great attention as a channel material for thin film transistors(TFTs) as next-generation display panel backplanes due to its superior electrical and physical properties such as a high mobility, low off-current, high sub-threshold slope, flexibility, and optical transparency. For the purpose of fabricating high performance IGZO TFTs, a thermal recovery process above a temperature of $300^{\circ}C$ is required for recovery or rearrangement of the ionic bonding structure. However diffused metal atoms from source/drain(S/D) electrodes increase the channel conductivity through the oxidation of diffused atoms and reduction of $In_2O_3$ during the thermal recovery process. Threshold voltage ($V_{TH}$) shift, one of the electrical instability, restricts actual applications of IGZO TFTs. Therefore, additional investigation of the electrical stability of IGZO TFTs is required. In this paper, we demonstrate the effect of Ti diffusion and modulation of interface traps by carrying out an annealing process on IGZO. In order to investigate the effect of diffused Ti atoms from the S/D electrode, we use secondary ion mass spectroscopy (SIMS), X-ray photoelectron spectroscopy, HSC chemistry simulation, and electrical measurements. By thermal annealing process, we demonstrate VTH shift as a function of the channel length and the gate stress. Furthermore, we enhance the electrical stability of the IGZO TFTs through a second thermal annealing process performed at temperature $50^{\circ}C$ lower than the first annealing step to diffuse Ti atoms in the lateral direction with minimal effects on the channel conductivity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.3
• /
• pp.576-581
• /
• 2005

In this paper. the a-Si:H TFT using ferroelectric of $SrTiO_3$ as a gate insulator is fabricated on glass. High k gate dielectric is required for on-current, threshold voltage and breakdown characteristics of TFT Dielectric characteristics of ferroelectric are superior to $SiO_2$ and $Si_3N_4$. Ferroelectric increases on-current and decreases threshold voltage of TFT and also ran improve breakdown characteristics.$SrTiO_4$ thin film is deposited by e-beam evaporation. Deposited films are annealed for 1 hour in N2 ambient at $150^{\circ}C\~600^{\circ}C$. Dielectric constant of ferroelectric is about 60-100 and breakdown field is about IMV/cm. In this paper, the TFT using ferroelectric consisted of double layer gate insulator to minimize the leakage current. a-SiN:H, a-Si:H (n-type a-Si:H) are deposited onto $SrTiO_3$ film to make MFNS(Metal/ferroelectric/a-SiN:H/a-Si:H) by PECVD. In this paper, TFR using ferroelectric has channel length of$8~20{\mu}m$ and channel width of $80~200{\mu}m$. And it shows that drain current is $3.4{\mu}A$at 20 gate voltage, $I_{on}/I_{off}$ is a ratio of $10^5\~10^8,\;and\;V_{th}$ is$4\~5\;volts$, respectively. In the case of TFT without having ferroelectric, it indicates that the drain current is $1.5{\mu}A$ at 20gate voltage and $V_{th}$ is $5\~6$ volts. If properties of the ferroelectric thin film are improved, the performance of TFT using this ferroelectric thin film can be advanced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.452-455
• /
• 2003

[ $ZrO_2$ ] dielectric layers were grown on the p-type Si (100) substrate by metalorganic molecular beam epitaxy(MOMBE). Zrconium t-butoxide, $Zr(O{\cdot}t-C_4H_9)_4$ was used as a Zr precursor and Argon gas was used as a carrier gas. The thickness of the layers was measured by scanning electron microscopy (SEM) and the properties of the $ZrO_2$ layers were evaluated by X-ray diffraction, high frequency capacitance-voltage measurement. and HF C-V measurements have shown that $ZrO_2$ layer grown by MOMBE has a high dielectric constant (k=18-19). The growth rate is affected by various process variables such as substrate temperature, bubbler temperature, Ar, and $O_2$ gas flows.