• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.6
• /
• pp.817-824
• /
• 2016

A simultaneous bidirectional transceiver over a single wire has been developed in a 65 nm CMOS technology for a command and control bus. The echo signals of the simultaneous bidirectional link are cancelled by controlling the decision level of receiver comparators without power-hungry operational amplifier (op-amp) based circuits. With the clock information embedded in the rising edges of the signals sent from the source side to the sink side, the data is recovered by an open-loop digital circuit with 20 times blind oversampling. The data rate of the simultaneous bidirectional transceiver in each direction is 75 Mbps and therefore the overall signaling bandwidth is 150 Mbps. The measured energy efficiency of the transceiver is 56.7 pJ/b and the bit-error-rate (BER) is less than $10^{-12}$ with $2^7-1$ pseudo-random binary sequence (PRBS) pattern for both signaling directions.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.6B
• /
• pp.848-855
• /
• 2001

본 논문에서는 GHz 대역의 고속 클럭 신호를 필요로 하는 데이터 통신 시스템 분야에 응용될 수 있는 새로운 구조의 클럭 및 데이터 복원회로를 제안하였다. 제안된 회로는 고속의 데이터 전송시 주로 사용되는 NRZ 형태의 데이터 복원에 적합한 구조로서 NRZ 데이터가 주입될 경우에 위상동기 회로에 발생하는 주요 잡음원인인 high frequency jitter를 방지하기 위한 새로운 위상 검출구조를 갖추고 있어서 보다 안정적인 클럭을 제공할 수 있다. 또 가변적인 지연시간을 갖는 delay cell을 이용한 위상검출기를 제안하여 위상 검출기가 갖는 dead zone 문제를 없애고, 항상 최적의 동작을 수행하여 빠른 동기 시간을 갖도록 하였다. Gbps급 대용량의 데이터를 복원하기 위한 클럭 생성을 목표로 하여 CMOS 0.25$\mu\textrm{m}$ 공정을 사용하여 설계한 후 그 동작을 HSPICE post-layout simulation을 통해 검증하였다.

• Journal of the Optical Society of Korea
• /
• v.20 no.5
• /
• pp.623-627
• /
• 2016

A power-adjustable fully-integrated CMOS optical receiver with multi-rate clock-and-data recovery circuit is presented in standard 65-nm CMOS technology. With supply voltage scaling, key features of the optical receiver such as bandwidth, power efficiency, and optical sensitivity can be automatically optimized according to the bit rates. The prototype receiver has −23.7 dBm to −15.4 dBm of optical sensitivity for 10⁻⁹ bit error rate with constant conversion gain around all target bit rates from 1.62Gbps to 8.1 Gbps. Power efficiency is less than 9.3 pJ/bit over all operating ranges.

• 한국정보통신설비학회:학술대회논문집
• /
• 2005.08a
• /
• pp.154-158
• /
• 2005

In this paper, we design optical receiver composed of CDR(clock and data recovery), SA(sense amp), TIA(transimpe dence amplifier), and decision circuit. The optical receiver can be classified to two main block, one is Deserializer composed of CDR and SA, another is PD receiver composed of preamplifier(샴), peak detector, etc. In this paper, we propose CDR using delayed data topology that could improve defects of existing CDR. The optical receiver that is proposed in this paper has the role of translation a 1.25 Gb/s optical signal to $10{\times}125 Mb/s$ array electric signals. This optical receiver is verified by simulator(hspice) using 0.35 um CMOS technology.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.7
• /
• pp.1877-1883
• /
• 1999

Synchronization of the clock at the ATM receiving terminal is studied. The technique analyzed here has been adapted by ITU-T as the standard for ATM timing recovery. This paper presents analysis of SRTS method itself and jitter in SRTS. The power pectrum and rms amplitude of SRTS jitter are calculated. The calculated average rms value for T1 1.544MHz source signal is 32.63ns and 0.15ns for E4 139.264MHz signal.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.3
• /
• pp.376-380
• /
• 1987

The closed-loop transfer function of 2-nd order PLL (phase-looked loop)of which loop filter has active-lag 1-st order is found. Considering the three criteria of system performance: the transient response time of the circuit, noise bandwidth by the linear analysis and stability which uses root-locus method, the optimum value of damping factor is 1.0 and the natural frequency which depends upon the signal frequency can be determined after consideration of the trade-off relationship between the transient response time and the noise bandwidth.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.1-6
• /
• 2011

This paper describes a phase modulation I/O (PMIO) serial interface circuit that supports 1Gbps transfer rate with 12mW power consumption at 1.2V supply. The proposed PMIO which consists of TX and RX blocks utilizes a phase modulation technique. The rising edge is fixed to get the clock phase information and falling edge has multi positions for the multi-data information to increase the transfer rate. The designed circuit use the 16 possible falling edge positions. The data transfer rate is four times faster than the clock rate. The circuit has been implemented using $0.13{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of transfer data (phase data) and recovery data.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.3
• /
• pp.404-416
• /
• 2015

Small-area, low-power coarse and fine frequency detectors (FDs) are proposed for an adaptive bandwidth referenceless CDR with a wide range of input data rate. The coarse FD implemented with two flip-flops eliminates harmonic locking as long as the initial frequency of the CDR is lower than the target frequency. The fine FD samples the incoming input data by using half-rate four phase clocks, while the conventional rotational FD samples the full-rate clock signal by the incoming input data. The fine FD uses only a half number of flip-flops compared to the rotational FD by sharing the sampling and retiming circuitry with PLL. The proposed CDR chip in a 65-nm CMOS process satisfies the jitter tolerance specifications of both USB 3.0 and USB 3.1. The proposed CDR works in the range of input data rate; 2 Gb/s ~ 8 Gb/s at 1.2 V, 4 Gb/s ~ 11 Gb/s at 1.5 V. It consumes 26 mW at 5 Gb/s and 1.2 V, and 41 mW at 10 Gb/s and 1.5 V. The measured phase noise was -97.76 dBc/Hz at the 1 MHz frequency offset from the center frequency of 2.5 GHz. The measured rms jitter was 5.0 ps at 5 Gb/s and 4.5 ps at 10 Gb/s.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.5 s.335
• /
• pp.31-38
• /
• 2005

The architecture and the implementation details of a UTMI(USB2.0 Transceiver Macrocell Interface) compatible USB2.0 transceiver chip were presented. To confirm the validation of the incoming data in noisy channel environment, a squelch state detector and a current mode Schmitt-trigger circuit were proposed. A current mode output driver to transmit 480Mbps data on the USB cable was designed and an on-die termination(ODT) which is controlled by a replica bias circuit was presented. In the USB system using plesiochronous clocking, to compensate for the frequency difference between a transmitter and a receiver, a synchronizer using clock data recovery circuit and FIFO was designed. The USB cable was modeled as the lossy transmission line model(W model) for circuit simulation by using a network analyzer measurements. The USB2.0 PHY chip was implemented by using 0.25um CMOS process and test results were presented. The core area excluding the IO pads was $0.91{\times}1.82mm^2$. The power consumptions at the supply voltage of 2.5V were 245mW and 150mW for high-speed and full-speed operations, respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.12
• /
• pp.1-9
• /
• 2001

In the APON(ATM Passive Optical Network), the transmission of the upstream traffic is based on a TDMA(Time Division Multiple Access) method that an OLT(Optical Line Termination) permits ONUs(Optical Network Units) sending cells by allocating time slots. Because the upstream is not a streaming mode, the cell synchronizer has to be operated in the burst mode. Also, the cell phase monitor is required to prevent collisions between cells which are transmitted by multiple ONUs through a single optical fiber. In this paper, a TDMA burst cell synchroniser is implemented with the FPGA(Field Programmable Gate Array) being used in the APON based on G.983.1 for transmitting upstream cells. It has two main functions which are the upstream data recovery and the phase monitoring. The former is to recover the upstream data and clock in the OLT by seeking the preamble which is the overhead of the upstream time slot and by aligning the phase of the bit and cell with the system clock. The latter is to provide the information to the ONU to compensate for the equalization delay by monitoring continuously the phase difference between adjacent cells to avoid the cell collision on the upstream.