• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.95-98
• /
• 2012

This paper describes a multiphase delay-locked loop (DLL) that generates a 32-phase output clock over the operating frequency range of 40 MHz to 280 MHz. The matrix-based delay line is used for high resolution of 1-bit delay. A calibration scheme, which improves the linearity of a delay line, is achieved by calibrating the nonlinearity of the input stage of the matrix. The multi-phase DLL is fabricated by using 0.11-${\mu}m$ CMOS process with a 1.2 V supply. At the operating frequency of 125MHz, the measurement results shows that the DNL is less than +0.51/-0.12 LSB, and the measured peak-to-peak jitter of the multi-phase DLL is 30 ps with input peak-to-peak jitter of 12.9 ps. The area and power consumption of the implemented DLL are $480{\times}550{\mu}m^2$ and 9.6 mW at the supply voltage of 1.2 V, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.387-394
• /
• 2016

This paper presents a fully digital delay locked loop (DLL) that can acquire lock in four clock cycles with a resolution of a 1/4 NAND-delay. The proposed DLL with a multi-dither-free phase detector acquires the initial lock in four clock cycles with 1/2 NAND-delay. Then, it utilizes a multi-dither-free phase detector, a region accumulator, and phase blenders, to improve the resolution to a 1/4 NAND-delay. The region accumulator which continuously steers the control registers and the phase blender, adaptively controls the tracking bandwidth depending on the amount of jitter, and effectively suppresses the dithering jitter. Fabricated in a 65 nm CMOS process, the proposed DLL occupies $0.0432mm^2$, and consumes 3.7 mW from a 1.2-V supply at 2 GHz.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.281-284
• /
• 2001

This paper describes an analog multi-phase delay-locked loop (DLL) to solve the harmonic lock problem using current-starved inverter and shunt-capacitor delay cell. The DLL can be used not only as an internal clock buffer of microprocessors and memory It's but also as a multi-phase clock generator for gigabit serial interfaces. The proposed circuit was simulated in a 0.25${\mu}{\textrm}{m}$ CMOS technology to solve harmonic lock problem and to realize fast lock-on time and low-jitter we verified time interval less than 40 ps as the simulation results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.259-262
• /
• 2012

This paper describes a delay-locked loop (DLL) that generates a 64-phase clock with the operating frequency of 125MHz. The proposed DLL use a $4{\times}8$ matrix-based delay line to improve the linearity of a delay line. The output clock with 64-phase is generated by using a CMOS multiplex and a inverted-based interpolator from 32-phase clock which is the output clock of the $4{\times}8$ matrix-based delay line. The circuit for an initial phase lock, which is independent on the duty cycle ratio of the input clock, is used to prevent from the harmonic lock of a DLL. The proposed DLL is designed using a $0.18-{\mu}m$ CMOS process with a 1.8 V supply. The simulated operating frequency range is 40 MHz to 200 MHz. At the operating frequency of a 125 MHz, the worst phase error and jitter of a 64-phase clock are +11/-12 ps and 6.58 ps, respectively.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.44 no.1
• /
• pp.74-84
• /
• 2007

This paper presents a new dual-loop Delay Locked Loop(DLL) to expand the delay lock range of a conventional DLL. The proposed dual-loop DLL contains a Coarse_loop and a Fine_loop, and its operation utilizes one of the loops selected by comparing the initial time-difference among the reference clock and 2 internal clocks. The 2 internal clock signals are taken, respectively, at the midpoint and endpoint of a VCDL and thus are $180^{\circ}$ separated in phase. When the proposed DLL is out of the conventional lock range, the Coarse_loop is selected to push the DLL in the conventional lock range and then the Fine_loop is used to complete the locking process. Therefore, the proposed DLL is always stably locked in unless it is harmonically false-locked. Since the VCDL employed in the proposed DLL needs two control voltages to adjust the delay time, it uses TG-based inverters, instead of conventional, multi-stacked, current-starved inverters, to compose the delay line. The new VCDL provides a wider delay range than a conventional VCDL In overall, the proposed DLL demonstrates a more than 2 times wider lock range than a conventional DLL. The proposed DLL circuits have been designed, simulated and proved using 0.18um, 1.8V TSMC CMOS library and its operation frequency range is 100MHz${\sim}$1GHz. Finally, the maximum phase error of the DLL locked in at 1GHz is less than 11.2ps showing a high resolution and the simulated power consumption is 11.5mW.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.4
• /
• pp.303-317
• /
• 2013

Two novel clocking strategies for a high-speed multi-channel serializer-deserializer (SERDES) are proposed in this paper. Both of the clocking strategies are based on groups, which facilitate flexibility and expansibility of the SERDES. One clocking strategy is applicable to moderate parallel I/O cases, such as high density, short distance, consistent media, high temperature variation, which is used for the serializer array. Each group within the strategy consists of a full-rate phase-locked loop (PLL), a full-rate delay-locked loop (DLL), and two fixed phase alignment (FPA) techniques. The other is applicable to more awful I/O cases such as higher speed, longer distance, inconsistent media, serious crosstalk, which is used for the deserializer array. Each group within the strategy is composed of a PLL and two DLLs. Moreover, a half-rate version is chosen to realize the desired function of 1:2 deserializer. Based on the proposed clocking strategies, two representative ICs for each group of SERDES are designed and fabricated in a standard $0.18{\mu}m$ CMOS technology. Measurement results indicate that the two SERDES ICs can work properly accompanied with their corresponding clocking strategies.

• Journal of IKEEE
• /
• v.26 no.4
• /
• pp.714-721
• /
• 2022

A phase-locked loop (PLL)-based frequency synthesizer is proposed for a system on a chip (SoC) using multi-frequency clock signals. The proposed PLL-based frequency synthesizer consists of a charge pump PLL which is implemented by a phase frequency detector (PFD), a charge pump (CP), a loop filter, a voltage controlled oscillator (VCO), and a frequency divider, and an edge combiner. The PLL outputs a 12-phase clock by a VCO using six differential delay cells. The edge combiner synthesizes the frequency of the output clock through edge combining and frequency division of the 12-phase output clock of the PLL. The proposed PLL-based frequency synthesizer is designed using a 55-nm CMOS process with a 1.2-V supply voltage. It outputs three clocks with frequencies of 166 MHz, 83 MHz and 124.5MHz for a reference clock with a frequency of 20.75 MHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2409-2418
• /
• 2013

Two frequency synthesizers are proposed to generate a clock for a sub-sampler of an on-chip oscilloscope in this paper. These proposed frequency synthesizers are designed by using a multi-phase delayed-locked loop (DLL)-based phase selector and a fractional-N phase-locked loop (PLL), and they are analyzed by comparing simulation results of each frequency synthesizer. Two proposed frequency synthesizers are designed using a 65-nm CMOS process with a 1V supply and output the clock with the frequency of 121.15 MHz when the frequency of an input clock is 125 MHz. The designed frequency synthesizer using a multi-phase DLL-based phase selector has the area of 0.167 $mm^2$ and the peak-to-peak jitter performance of 2.88 ps when it consumes the power of 4.75 mW. The designed frequency synthesizer using a fractional-N PLL has the area of 0.662 $mm^2$ and the peak-to-peak jitter performance of 7.2 ps when it consumes the power of 1.16 mW.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.1
• /
• pp.137-144
• /
• 2013

A delay-locked loop (DLL) that generates a 32-phase clock with the operating frequency of 125 MHz is introduced. The proposed DLL uses a delay line of $4{\times}8$ matrix architecture to improve a differential non-linearity (DNL) of the delay line. Furthermore, a integral non-linearity (INL) of the proposed DLL is improved by calibrating phases of clocks that is supplied to four points of an input stage of the $4{\times}8$ matrix delay line. The proposed DLL is fabricated by using $0.11-{\mu}m$ CMOS process with a 1.2 V supply. The measured operating frequency range of the implemented DLL is 40 MHz to 280 MHz. At the operating frequency of 125MHz, the measurement results shows that the DNL and INL are +0.14/-0.496 LSB and +0.46/-0.404 LSB, respectively. The measured peak-to-peak jitter of the output clock is 30 ps when the peak-to-peak jitter of the input clock is 12.9 ps. The area and power consumption of the implemented DLL are $480{\times}550{\mu}m^2$ and 9.6 mW, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.12 no.4
• /
• pp.433-448
• /
• 2012

A source-synchronous receiver based on a delay-locked loop is presented. It employs a shared global calibration control between channels, yet achieves channel expandability for high aggregate I/O bandwidth. The global calibration control accomplishes skew calibration, equalizer adaptation, and phase lock of all the channels in a calibration period, resulting in the reduced hardware overhead and area of each data lane. In addition, the weight-adjusted dual-interpolating delay cell, which is used in the multiphase DLL, guarantees sufficient phase linearity without using dummy delay cells, while offering a high-frequency operation. The proposed receiver is designed in the 90-nm CMOS technology, and achieves error-free eye openings of more than 0.5 UI across 9-28 inch Nelco4000-6 microstrips at 4-7 Gb/s and more than 0.42 UI at data rates of up to 9 Gb/s. The data lane occupies only $0.152mm^2$ and consumes 69.8 mW, while the rest of the receiver occupies $0.297mm^2$ and consumes 56.0 mW at the 7- Gb/s data-rate and supply voltage of 1.35 V.