• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.455-458
• /
• 2011

4:10 deserializer is proposed to recover 1:10 serial data using 1/4-rate clock. And then, 1/4-rate CDR(Clock and Data Recovery) circuit was designed for SERDES of high-speed serial display interface. The reduction of clock frequency using 1/4-rate clocking helps relax the speed limitation when higher data transfer is demanded. This circuit is composed of 1/4-rate sampler, PEL(Phase Error Logic), Majority Voting, Digital Filter, DPC(Digital to Phase Converter) and 4:10 deserializer. The designed CDR has been designed in a standard $0.18{\mu}m$ 1P6M CMOS technology and the recovered data jitter is 14ps in simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.12
• /
• pp.1084-1096
• /
• 2016

This paper presents method of design and analysis of a high-speed serial interface connector with a data rate of 12.5 Gbps. A high-speed serial interface connector is composed of various material and complex structures. It is very difficult to match the impedance of each discontinuous portion of connector. Therefore, this paper proposes the structure of a connector line that be simplified a connector. In the structure of proposed connector line, this research presents a method for extracting R, L, C and G parameters, analyzing the differential mode impedance, and minimizing the impedance discontinuity using time domain transmissometry and time domain reflectometry. This paper applies the proposed methods in the connector line to the high-speed serial interface connector. The proposed high-speed serial interface connector, which consists of forty-four pins, is analyzed signal transmission characteristics by changing the width and spacing of the four pins. According to the analysis result, as the width of the ground pin increases, the impedance decreases slightly. And as the distance between the ground pin and the signal pin increases, the impedance increases. In addition, as the width of the signal pin increases, the impedance decreases. And as the distance between the signal pin and the signal pin increases, the impedance decreases. The impedance characteristic of initial connector presents ranges from 96 to $139{\Omega}$. Impedance characteristic after applying the structure of proposed connector is shown as a value between 92.6 to $107.5{\Omega}$. This value satisfies the design objective $100{\Omega}{\pm}10%$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.522-525
• /
• 2006

Recently, mobile devices support multi-functions such as 3D game, wireless internet, moving pictures, DMB, GPS, and PMP. Bigger size of display device is indispensable to support these functions and higher speed of the interface is needed. However, conventional parallel interfaces between processor and display nodule are not competent enough for that high speed transfers. High-speed serial interface is beginning to appear as an alternative for parallel interface. The advantages of the serial interface are high bandwidth, small number of interconnections, low-power consumption, and good quality of electro-magnetic interference. In this paper, we implement serial interface and use it for a display module. LVDS is used for PHY layer and a defined packet is used for link layer. The feature of the implemented serial interface is the reduced number of interconnections with enough bandwidth.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.12
• /
• pp.46-55
• /
• 2014

PCB design technology for high-speed transmission line has been developed continuously. Adapting to the high capacity of the communication system, switch fabric interface used for backplane is being standardized to accommodate more than 10Gbps serial interface. In this paper, various computer simulations are performed to compare the performance of each transmission line per length according to PCB material, and also to analyze the effect from via stub length and crosstalk, for the purpose of applying 11.5Gbps serial interface as a switch fabric interface in tera-bit switching system. As a result of the simulation, important design issues, such as PCB material of each board supporting 8dB improvement in transmission loss using low loss PCB, maximum available stub length on transmission line via, whether or not to apply the backdrill process to the via, and the clearance of the differential pair between transmission lines, are determined. The most efficient system architecture which could be applied 11.5Gbps serial interface in all switch fabric interfaces is defined from the simulation results.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.212-214
• /
• 2005

The MDDI(Mobile Digital Display Interface) standard is an optimized high-speed serial interconnection technology developed by Qualcomm and supports the VESA(Video Electronics Standard Association). It increases reliability and reduces power consumption in clamshell phones by decreasing the number of wires to interconnect with the LCD display. In this paper, the MDDI host is designed using VHDL and implemented on FPGA. We demonstrates that the MDDI host is connected with S3CA460 LCD controller is designed by Samsung Electronics Co. and display a steal image to the LCD.

• ETRI Journal
• /
• v.34 no.1
• /
• pp.35-43
• /
• 2012

This paper presents a delay-locked-loop-based clock and data recovery (CDR) circuit design with a nB(n+2)B data formatting scheme for a high-speed serial display interface. The nB(n+2)B data is formatted by inserting a '01' clock information pattern in every piece of N-bit data. The proposed CDR recovers clock and data in 1:10 demultiplexed form without an external reference clock. To validate the feasibility of the scheme, a 1.7-Gbps CDR based on the proposed scheme is designed, simulated, and fabricated. Input data patterns were formatted as 10B12B for a high-performance display interface. The proposed CDR consumes approximately 8 mA under a 3.3-V power supply using a 0.35-${\mu}m$ CMOS process and the measured peak-to-peak jitter of the recovered clock is 44 ps.

• Journal of IKEEE
• /
• v.10 no.2 s.19
• /
• pp.128-133
• /
• 2006

This paper describes a high speed interface circuit using redundant multi-valued logic for high speed communication ICs. This circuit is composed of encoding circuit that serial binary data are received and converted into parallel redundant multi-valued data, and decoding circuit that converts redundant multi-valued data to parallel binary data. Because of the multi-valued data conversion, this circuit makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, the proposed 1:4 DEMUX (demultiplexer, serial-parallel converter), was designed using a 0.35um standard CMOS technology. Proposed DEMUX is achieved an operating speed of 4.5Gb/s with a supply voltage of 3.3V and with power consumption of 53mW. The operating speed of this circuit is limited by the maximum frequency which the 0.35um process has. Therefore, this circuit is to achieve CMOS communication ICs with an operating speed greater than 10Gb/s in submicron process of high operating frequency.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.35C no.1
• /
• pp.34-41
• /
• 1998

In this paper, I designed a P1394 serial bus chip as new bus interface architecture which can transmit the multimedia data at the rate of 400 Mbps and guarantee necessary bandwidth. because multimedia data become meaningless data after appropriate time, it is necessary to transfer multimedia data in real time, P1394 serial bus chip designed in this paper support isochronous transfer mode to solve this problem. Also, designed P1394 serial bus chip can transfer high quality video data or high quality audio data because it support the speed of 400 Mbps. While user must set device ID manually in previous interface such as SCSI, device ID is automatically determined if user connect each node with designed P1394 serial bus cable and power on. To design this chip, I verified the behavioral of the entrire system and synthesized layout. Also, I did layout the analog blocks and blocks which must be optimized in full custom.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.148-151
• /
• 2005

This paper proposes a high speed interface using redundant multi-valued logic for high speed communication ICs. This circuit is composed of encoding circuit that serial binary data are received and converted into parallel redundant multi-valued data, and decoding circuit that convert redundant multi-valued data to parallel binary data. Because of the multi-valued data conversion, this circuit makes it possible to achieve higher operating speeds than that of a conventional binary logic. Using this logic, a 1:4 demultiplexer (DEMUX, serial-parallel converter) IC was designed using a 0.35${\mu}m$ standard CMOS Process. Proposed demultiplexer is achieved an operating speed of 3Gb/s with a supply voltage of 3.3V and with power consumption of 48mW. Designed circuit is limited by maximum operating frequency of process. Therefore, this circuit is to achieve CMOS communication ICs with an operating speed greater than 3Gb/s in submicron process of high of operating frequency.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.1
• /
• pp.33-41
• /
• 2019

We propose an embedded solution to design a high-speed and high-accuracy 16bit analog-digital signal processing interface for the control systems using various external analog signals. Choosing TMS320F28377D micro controller unit (MCU) featuring high-performance processing in the 32-bit floating point operation, low power consumption, and various I/O device supports, we design and build the proposed system that supports both 16-bit analog-digital converter (ADC) interface and high precision digital-analog converter (DAC) interface. The ADC receives voltage-level differential signals from fully differential amplifiers, and the DAC communicates with MCU through 50 MHz bandwidth high-fast serial peripheral interface (SPI). We port the boot loader and device drivers to the implemented board, and construct the firmware development environment for the application programming. The performance of the entire implemented system is demonstrated by analog-digital signal processing tests, and is verified by comparing the test results with those of existing similar systems.