• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.389-389
• /
• 2010

In this paper, an investigation of the benefits of gate oxide for 8" the manufacturing of Trench MOSFETs and its impact on device performance is presented. Layout dimensions of trench power MOSFETs have been continuously reduced in order to decrease the specific on-resistance, maintaining equal vertical dimensions. We discuss experimental results for devices with a pitch size down fabricated with an unconventional gate trench topology and a simplified manufacturing scheme. The fabricated Trench MOSFETs are observed the trench gate oxidation by SEM.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1501-1502
• /
• 2011

In this paper, an investigation of the 8" process for Trench Power MOSFET Application and Trench MOSFETs and its impact on device performance is presented. Layout dimensions of trench power MOSFETs have been continuously reduced in order to decrease the specific on-resistance, maintaining equal vertical dimensions. We discuss experimental results for devices with a pitch size down fabricated with an unconventional gate trench topology and a simplified manufacturing scheme. The fabricated Trench MOSFETs are observed the trench gate oxidation by SEM.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권3호
• /
• pp.263-267
• /
• 2014

Super junction trench gate power MOSFETs have been receiving attention in terms of the trade-off between breakdown voltage and on-resistance. The vertical structure of super junction trench gate power MOSFETs allows the on-resistance to be reduced compared with conventional Trench Gate Power MOSFETs. The heat release of devices is also decreased with the reduction of on-resistance. In this paper, Lattice Temperature of two devices, Trench Gate Power MOSFET and Super junction trench gate power MOSFET, are compared in several temperature circumstance with the same Breakdown Voltage and Cell-pitch. The devices were designed by 100V Breakdown voltage and measured from 250K Lattice Temperature. We have tried to investigate how much temperature rise in the same condition. According as temperature gap between top of devices and bottom of devices, Super junction trench gate power MOSFET has a tendency to generate lower heat release than Trench Gate Power MOSFET. This means that Super junction trench gate power MOSFET is superior for wide-temperature range operation. When trench etching process is applied for making P-pillar region, trench angle factor is also important component. Depending on trench angle, characteristics of Super junction device are changed. In this paper, we focus temperature characteristic as changing trench angle factor. Consequently, Trench angle factor don't have a great effect on temperature change.

• ETRI Journal
• /
• 제24권5호
• /
• pp.333-340
• /
• 2002

We propose a new process technique for fabricating very high-density trench MOSFETs using 3 mask layers with oxide spacers and a self-aligned technique. This technique reduces the device size in trench width, source, and p-body region with a resulting increase in cell density and current driving capability as well as cost-effective production capability. We were able to obtain a higher breakdown voltage with uniform oxide grown along the trench surface. The channel density of the trench DMOSFET with a cell pitch of 2.3-2.4 ${\mu}m$ was 100 Mcell/$in^2$ and a specific on-resistance of 0.41 $m{\Omega}{\cdot}cm^2$ was obtained under a blocking voltage of 43 V.

• Journal of Electrical Engineering and Technology
• /
• 제9권3호
• /
• pp.843-847
• /
• 2014

In Super Junction (SJ) MOSFETs, charge balance is the most important issue of the SJ fabrication process. In order to achieve the best electrical characteristics, such as breakdown voltage and on-resistance, the N-type and P-type drift regions must be fully depleted when the drain bias approaches the breakdown voltage, which is known as the charge balance condition. In conventional charge balance analysis, based on multi-epi process SJ MOSFETs, analytical model has only N, P pillar width and doping concentration parameter. But applying a conventional charge balance principle to trench filling process, easier than Multi-epi process, is impossible due to the missing of the trench angle parameter. To achieve much more superior characteristics of on-resistance in trench filling SJ MOFET, the appropriate trench angle is necessary. So in this paper, modulated charge balance analysis is proposed, in which a trench angle parameter is added. The proposed method is validated using the TCAD simulation tool.

• 한국정보통신학회논문지
• /
• 제10권12호
• /
• pp.2258-2263
• /
• 2006

본 논문은 shallow trench isolation (STI) 공정에서 ILD (inter-layer dielectric) 막의 수분에 의해 야기되는 단 채널 (short-channel) nMOSFET의 hump 특성의 원인을 분석하고 억제 방법을 제안하였다. 다양한 게이트를 가지는 소자와 TDS-APIMS(Thermal Desorption System-Atmospheric Pressure Ionization Mass Spectrometry) 측정을 이용하여 hump 특성을 체계적으로 분석하였고, 분석을 바탕으로 단 채널 hump모델을 제안하였다. 제안된 모델에 의한 단 채널 nMOSFET의 hump 현상은 poly-Si 게이트 위의 ILD 막의 수분이 상부의 SiN 막에 의해 밖으로 확산되지 못하고 게이트와 STI의 경계면으로 확산하여 발생한 것이 며, 이를 개선하기 위해 상부의 SiN 막의 증착 전 열공정을 통해 ILD 막의 수분을 효과적으로 배출시킴으로써 hump 특성을 성공적으로 억제하였다.

• 대한전자공학회논문지SD
• /
• 제40권9호
• /
• pp.638-643
• /
• 2003

Channel width dependence of hot-carrier effect in nMOSFET with shallow trench isolation is analyzed. $I_{sub}$- $V_{G}$ and $\Delta$ $I_{ㅇ}$ measurement data show that MOSFETs with narrow channel-width are more susceptible to the hot-carrier degradation than MOSFETs with wide channel-width. By analysing $I_{sub}$/ $I_{D}$, linear $I_{D}$- $V_{G}$ characteristics, thicker oxide-thickness at the STI edge is identified as the reason for the channel-width dependent hot-carrier degradation. Using the charge-pumping method, $N_{it}$ generation due to the drain avalanche hot-carrier (DAHC) and channel hot-electron (CHE) stress are compared. are compared.

• 한국컴퓨터산업교육학회:학술대회논문집
• /
• 한국컴퓨터산업교육학회 2003년도 제4회 종합학술대회 논문집
• /
• pp.67-70
• /
• 2003

In this paper, propose a new structure of MOFET(Metal-Oxide-Semiconductor Field Effect Transistor) which is widely application for semiconductor technologies. Eleminate the latch-up effect caused by closed devices when conpose a electronic circuit using proposed devices. In this device have a completely isolation structure, and advantage of leakage current elimination. Each independent devices are isolated by trench-well and oxide layer of SOI substrate. Using trench gate and self aligned techniques reduces parasitic capacitance between gate and source, drain. In this paper, we proposed the new structure of SOI MOSFET which has completely isolation and contains trench gate electrodes and SOI wafers. It is simulated by MEDICI that is device simulator.

• ETRI Journal
• /
• 제35권4호
• /
• pp.632-637
• /
• 2013

In this paper, we propose a superjunction trench gate MOSFET (SJ TGMOSFET) fabricated through a simple p-pillar forming process using deep trench and boron silicate glass doping process technology to reduce the process complexity. Throughout the various boron doping experiments, as well as the process simulations, we optimize the process conditions related with the p-pillar depth, lateral boron doping concentration, and diffusion temperature. Compared with a conventional TGMOSFET, the potential of the SJ TGMOSFET is more uniformly distributed and widely spread in the bulk region of the n-drift layer due to the trenched p-pillar. The measured breakdown voltage of the SJ TGMOSFET is at least 28% more than that of a conventional device.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.427-435
• /
• 2014

Segmented-channel MOSFETs (SegFETs) can achieve both good performance and variation robustness through the use of $HfO_2$ (a high-k material) to create the shallow trench isolation (STI) region and the very shallow trench isolation (VSTI) region in them. SegFETs with both an HTI region and a VSTI region (i.e., the STI region is filled with $HfO_2$, and the VSTI region is filled with $SiO_2$) can meet the device specifications for high-performance (HP) applications, whereas SegFETs with both an STI region and a VHTI region (i.e., the VSTI region is filled with $HfO_2$, and the STI region is filled with $SiO_2$) are best suited to low-standby power applications. AC analysis shows that the total capacitance of the gate ($C_{gg}$) is strongly affected by the materials in the STI and VSTI regions because of the fringing electric-field effect. This implies that the highest $C_{gg}$ value can be obtained in an HTI/VHTI SegFET. Lastly, the three-dimensional TCAD simulation results with three different random variation sources [e.g., line-edge roughness (LER), random dopant fluctuation (RDF), and work-function variation (WFV)] show that there is no significant dependence on the materials used in the STI or VSTI regions, because of the predominance of the WFV.