• Journal of IKEEE
• /
• v.20 no.2
• /
• pp.181-183
• /
• 2016

In this work, the merged PiN Schottky(MPS) diodes based silicon carbide(SiC) have been optimized and designed for 1200V diodes by 2D-atlas simulation tool. We investigated the optimized characteristics of SiC MPS diodes such as breakdown voltage and specific on-resistance by varying the doping concentrations of P-Grid/epi-layer and space of P-Grid, which are the most important parameters. The breakdown voltage and specific on-resistance, based on Baliga's Figure Of Merit (BFOM), have been compared with and the SiC-based MPS diodes show improved BFOMs with low values of specific on-resistance and high breakdown voltage. It has been demonstrated 1,200 V SiC MPS diodes will find useful applications in high voltage energy-efficient devices.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.5
• /
• pp.293-296
• /
• 2016

Using capacitance-voltage (C-V) and conductance-voltage (G/ω-V) measurements, the electrical properties of Cu/n-InP Schottky diodes were investigated. The values of C and G/ω were found to decrease with increasing frequency. The presence of interface states might cause excess capacitance, leading to frequency dispersion. The negative capacitance was observed under a forward bias voltage, which may be due to contact injection, interface states or minority-carrier injection. The barrier heights from C-V measurements were found to depend on the frequency. In particular, the barrier height at 200 kHz was found to be 0.65 eV, which was similar to the flat band barrier height of 0.66 eV.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.4
• /
• pp.106-111
• /
• 1996

Schottky diodes are fabricated on laser annealed and unannealed polysilicon substrate and their electrical characteristics are studied and analyzed. Current of laser annealed devices are larger than that of unannealed devices because of grain growth, decrease of grain boundary and trap density, lowering of grain boundary barrier height, decrease of dopant segregation. At low forward bias (<0.7V), currents of unanealed devices are larger. Soft breakdown voltages of laser annealed devices are larger than that of unannealed devices.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.2
• /
• pp.124-127
• /
• 2004

W/n-GaN Schottky diodes were irradiated with $^{60}Co\;{\gamma}-rays$ to doses up to 315Mrad. The barrier height obtained from current-voltage (I-V) measurements showed minimal change from its estimated initial value of ${\sim}0.4eV$ over this dose range, though both forward and reverse I-V characteristics show evidence of defect center introduction at doses as low as 150 Mrad. Post irradiation annealing at $500^{\circ}C$ increased the reverse leakage current, suggesting migration and complexing of defects. The W/GaN interface is stable to high dose of ${\gamma}-rays$, but Au/Ti overlayers employed for reducing contact sheet resistance suffer from adhesion problems at the highest doses.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.280-284
• /
• 2011

Silicon carbide (SiC)-based gas sensors can be operated at very high temperatures. So far, catalytic metal-schottky diodes respond fast to a change between a reducing and an oxidizing atmosphere. Therefore SiC diodes have been suggested for high temperature gas sensor applications. In this work, the effect of reactivity of the catalytic surface on the 4H-SiC sensor-structures in 375 K~775 K have been studied and some fundamental simulations have also been performed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.7
• /
• pp.533-538
• /
• 2001

The barrier height is found to increase from 0.25 to 0.690 eV for Schottky contacts on n-InGaAs using deposition of Ag on a substrate cooled to 77K(LT). Surface analysis leads to an interface model for the LT diode in which there are oxide compounds of In:O and As:O between the metal and semiconductor, leading to behavior as a metal-insulator-semiconductor diode. The metal film deposited t LT has a finer and more uniform structure, as revealed by scanning electron microscopy and in situ metal layer resistance measurement. This increased uniformity is an additional reason for the barrier height improvement. In contrast, the diodes formed at room temperature exhibit poorer performance due to an unpassivated surface and non-uniform metal coverage on a microscopic level.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1733-1736
• /
• 2008

ZnO thin films with preferred orientation along the (0 0 2) plane were fabricated by a sol-gel method. The effects of the annealing temperature, time, and thickness were studied by investigating UV-visible spectra, FT-IR spectra, and XRD of ZnO films. The films were dried and annealed ed at $100^{\circ}C,\;200^{\circ}C$, and $300^{\circ}C$ for 1hr, 2hrs, and 3hrs, respectively. The film showed the preferred (0 0 2) orientation and high transmittance near 90% in the visible range. Also, SEM images of the films exhibited very smooth surfaces without holes and cracks. Schottky diodes were fabricated by using ZnO sol-gel material. Au and Al were used as electrodes to make Ohmic and Schottky contacts, respectively. The annealing temperature, time and the thickness dependent I-V characteristics were presented in this article.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.4
• /
• pp.187-189
• /
• 2015

A charge-trap flash (CTF) thin film transistor (TFT) memory is proposed at a low-temperature process (≤ 450℃). The memory cell consists of a sputtered oxide-nitride-oxide (ONO) gate dielectric and Schottky barrier (SB) source/drain (S/D) junctions using nickel silicide. These components enable the ultra-low-temperature process to be successfully achieved with the ONO gate stacks that have a substrate temperature of room temperature and S/D junctions that have an annealing temperature of 200℃. The silicidation process was optimized by measuring the electrical characteristics of the Ni-silicided Schottky diodes. As a result, the Ion/Ioff current ratio is about 1.4×10⁵ and the subthreshold swing and field effect mobility are 0.42 V/dec and 14 cm²/V·s at a drain voltage of −1 V, respectively.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.192-195
• /
• 2001

In this report, we firstly have investigated the electrical characteristics of silicon carbide (SiC) schottky barrier diode and compared the characteristics to those of conventional Si diode through simulation and experiment. Secondly we have investigated the influence of two kinds of diodes to the power conversion circuit of the systems. From the investigation results it is verified that SiC schottky barrier diode is more superior to Si diode in thermal and reverse recovery, characteristics, which are the important factors in the size reduction and higher reliability of the systems. Finally though the experiment applied to PFC(Power Factor Correction) circuits, we precisely verified excellency to thermal characteristic of SiC schottky barrier diode any other diode.

• Journal of the Korean Vacuum Society
• /
• v.16 no.3
• /
• pp.197-204
• /
• 2007

Ultra thin Er-silicide layers formed by Er deposition on the clean p-silicon and in situ post annealing technique were investigated with respect to change of the Schottky barrier height. The formation of Er silicides was confirmed by XPS results. UPS measurements revealed that the workfunction of the silicide decreased and was saturated as the deposited Er thickness increased up to $10{\AA}$. We found that the silicides were mainly composed of Er5Si3 phase through the XRD experiments. After Schottky diodes were fabricated with the Er silicide/p-Si junctions, the Schottky barrier heights were calculated $0.44{\sim}0.78eV$ from the I-V measurements of the Schottky diodes. There was large discrepancy in the Schottky barrier heights deduced from the UPS with the ideal junction condition and the real I-V measurements, so that we attributed the discrepancy to the $Er_5Si_3$ phase in the Er-silicides and the large interfacial density of trap state of it.