• Journal of the Microelectronics and Packaging Society
• /
• v.18 no.1
• /
• pp.7-13
• /
• 2011

According to increasing of data transfer rate, printed circuit board (PCB) is required improvement of transmission speed. Optical PCB and its packaging technology can be one of the solutions that overcome the limitations of conventional electrical PCB. The data transmission capacity will be increased 10 Tbps at 2015. To this end, studies on various OPCB technologies are being conducted. For cost-effective and high- performance OPCB, studies of optical coupling by polymer replication process are conducted. In this work, optical waveguide and optical fiber array block were sequentially fabricated by polymer pattern replication method. Using this method we successfully demonstrate low loss optical fiber coupling between optical waveguide and optical fiber arrays. And researches on flip chip bonding process and using electro-optic connectors for packaging are conducted.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.981-984
• /
• 2010

생산성 증가 및 비용 절감을 위해 반도체 공정 기술을 단순화 시키는 것이 필요하다. WBL(Wafer Backside Lamination) 기술을 이용해 필름(film) 형태로 얇은 다이접착제를 웨이퍼(wafer)에 접착하여 반도체 칩과 PCB를 붙이는 방법과 직접 PCB에 다이접착제를 붙이는 방법을 사용하면 획기적으로 공정을 단순화 시킬 수 있다. 하지만 Lamination 기법은 고온을 이용하여 모듈화된 PCB에 접착하므로 전도와 복사에 의해 주변 접착제 필름이 녹아 버리는 문제점이 발생한다. 본 연구에서는 고온으로 인한 필름 융해 현상을 방지하기 위하여 배크라이트를 설치하였으며 CFD 해석을 통해 PCB와 반도체 칩을 접착시킬 때 열이 PCB에 미치는 영향을 살펴보았다.

• Journal of the Microelectronics and Packaging Society
• /
• v.28 no.2
• /
• pp.65-70
• /
• 2021

In this study, interfacial properties and mechanical properties of joints were reported after Cu pads finished with organic solderability preservative (OSP) on flame retardant-4 (FR-4) printed circuit board (PCB) and electronic components were joined with a Sn-57Bi-1Ag solder paste by using a laser bonding process. The laser bonding process was performed under various bonding conditions with changing a laser power and a bonding time and effects of bonding conditions on interfacial and mechanical properties of joints were analyzed. In order to apply for industry, properties of bonding joints using a reflow bonding process which are widely used were compared. When the laser bonding process were performed, we observed that Cu₆Sn₅ intermetallic compounds (IMCs) were fully formed at the interface although the bonding times were very short about 2 and 3 s. Furthermore, void formations of the joints by using the laser bonding process were suppressed at the joints with comparing to the reflow bonding process and shear strengths of bonding joints were higher than that by using the reflow bonding process. Therefore, in spite of a very short bonding time, it is expected that joints will be stably formed and have a high mechanical strength by using the laser bonding process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.265-271
• /
• 2008

TCP(Tape Carrier Package), COG (Chip On Glass), COF(Chip On Film) are three methods for connecting LDI(LCD Driver IC) with LCD panels. Especially COF is growing its portion of market place because of low cost and fine pitch correspondence. But COF has a problem of the lead broken failure in LCD module process and the usage of customer. During PCB (Printed Circuit Board) bonding process, the mismatch of the coefficient of thermal expansion between PCB and D-IC makes stress-concentration in COF lead, and also D-IC bending process during module assembly process makes the level of stress in COF lead higher. As an affecting factors of lead-broken failure, the effects of SR(Solder Resister) coating on the COF lead, surface roughness and grain size of COF lead, PI(Polyimide) film thickness, lead width and the ACF(Anisotropic Conductive Film) overlap were studied, The optimization of these affecting manufacturing processes and materials were suggested and verified to prevent the lead-broken failure.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.34-36
• /
• 2005

Copper wire bonding is an alternative interconnection technology that serves as a viable and cost saving alternative to gold wire bonding. In this paper, ultrasonic wedge bonding with $25{\mu}m$ copper wire on Au/Ni/Cu metallization of a PCB substrate was performed at ambient temperature. The central composite design of experiment (DOE) approach was applied to optimize the copper wire wedge bonding process parameters. After that, pull test of the wedge bond was performed to study the bond strength and to find the optimum bonding parameters. SEM was used to observe the cross section of the wedge bond. The pull test results show good performance of the wedge bond. Additionally, DOE results gave the optimized parameter for both the first bond and the second bond. Cross section analysis shows a continuous interconnection between the copper wire and Au/Ni/Cu metallization. The diffusion of Cu into the Au layer was also observed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.191-191
• /
• 2009

In this paper, we have confirmed the temperature of LED chip and McPCB with thermal simulation program which is CFDedign V10 for analysis the thermal flow of HP LED package. we have known that the heat from LED chip is transferred through heat slug to copper layer of McPCB. the temperature of LED chip shows 85.11 [$^{\circ}C$], which shows the temperature gap of 7.52 [$^{\circ}C$] against McPCB. the gap of temperature affect reliability of the wire bonding and die attachment. therefore, copper layer of heat slug on the McPCB should designed with the largest dimension.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.8-13
• /
• 2006

Recent RF SAW filters are made using a HTCC package with a CSP(chip scale Package) technology. This paper describes a development of a new $1.4{\times}1.1\;and\;2.0{\times}1.4mm$ RF SAW liters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.10a
• /
• pp.39-45
• /
• 2000

A small camera module fabricated by including bare chip bonding methods is utilized to realize advanced mobile devices. One of the driving forces is the TOG (Tape On Glass) bonding method which reduces the packaging size of the image sensor clip. The TOG module is a new thinner and smaller image sensor module, using flip chip interconnection method with the ACP (Anisotropic Conductive Paste). The TOG production process was established by determining the optimum bonding conditions for both optical glass bonding and image sensor clip bonding lo the flexible PCB. The bonding conditions, including sufficient bonding margins, were studied. Another bonding method is the flip chip bonding method for DSP (Digital Signal Processor) chip. A new AC\ulcorner was developed to enable the short resin curing time of 10 sec. The bonding mechanism of the resin curing method was evaluated using FEM analysis. By using these flip chip bonding techniques, small camera module was realized.

• Korean Journal of Metals and Materials
• /
• v.47 no.4
• /
• pp.261-266
• /
• 2009

The mechanical and electrical properties of ball grid array (BGA) solder joints were measured, consisting of Sn-3.5Ag, with organic solderability preservative (OSP)-finished Cu pads and Electroless Nickel/Immersion Gold (ENIG) surface finishes. The mechanical properties were measured by die shear test. When ENIG PCB was upper joint and OSP PCB was lower joint, the highest shear force showed at the third reflow. When OSP PCB was upper joint and ENIG PCB was lower joint, the highest shear force showed at the forth reflow. For both joints, after the die shear results reached the highest shear force, shear force decreased as a function of increasing reflow number. Electrical property of the solder joint decreased with the function of increasing reflow number. The scanning electron microscope results show that the IMC thickness at the bonding interface gets thicker while the number of reflow increases.

• The Journal of the Convergence on Culture Technology
• /
• v.4 no.3
• /
• pp.209-212
• /
• 2018

Anisotropic conductive film(ACF) bonding is widely used for making fine interconnections between two different materials where soldering is not easily applicable. There are three constraints for the successful implementation of ACF bonding. A bonding contact should be pressed by a hot head with the right pressure and temperature for a pre-defined curing time. In this paper, a method for ACF bonding based on machine vision system is proposed and verified through some experiments. The system calculates the position and orientation of printed circuit boards(PCBs) on a bonding table and estimates the optimal hitting point where the hot head should be applied. Experimental results show that the proposed system achieves better adhesive strength by providing head flatness over contact surfaces.