• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.84-87
• /
• 2010

We manufacture an antifuse OTP (One-time programmable) cell for analog trimming which will be used in power management ICs. For the antifuse cell using dual program voltage of VPP (=7V) and VNN (=-5V), the thin gate oxide is broken down by applying a voltage higher than the hard break-down voltage to the terminals of the antifuse. The area of the manufactured antifuse OTP cell using $0.18{\mu}m$ BCD process is $48.01{\mu}m^2$ and is about 44.6 percent of that of an eFuse cell. The post-program resistances of the antifuse are good with the values under several kilo ohms when we measure twenty test patterns.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.1
• /
• pp.115-122
• /
• 2014

In this paper, reliability is secured by sensing a post-program resistance of several tens of kilo ohms and restricting a read current flowing over an unblown eFuse within $100{\mu}A$ since RWL driver and BL pull-up load circuits using a regulated voltage of V2V ($=2V{\pm}10%$) are proposed to have a wide operating voltage range for eFuse OTP memory. Also, when a comparison of a cell array of 1 row ${\times}$ 32 columns with that of 4 rows ${\times}$ 8 columns is done, the layout size of 4 rows ${\times}$ 8 columns is smaller with $187.065{\mu}m{\times}94.525{\mu}m$ ($=0.01768mm^2$) than that of 1 row ${\times}$ 32 columns with $735.96{\mu}m{\times}61.605{\mu}m$ ($=0.04534mm^2$).

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.6
• /
• pp.2697-2701
• /
• 2012

The yield of OTP devices using anti-fuse MOS capacitor have been affected by the input resistance, the size of the pass transistor and the read transistor, and the readout voltage of programed cell. To investigate the element which gives an effect to yield, we analyze the full map data of the resistance characterization of OTP device and those data in a various experimental condition. As a result, we got the optimum conditions which is necessary to the yield improvement. The optimum conditions are as follows: Input resistance is 50 ohms, the channel length of pass transistor is 10um, read voltage is 2.8 volt, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.2
• /
• pp.306-316
• /
• 2016

In this paper, an NMOS-diode eFuse OTP (One-Time Programmable) memory cell is proposed using a parasitic junction diode formed between a PW (P-Well), a body of an isolated NMOS (N-channel MOSFET) transistor with the small channel width, and an n+ diffusion, a source node, in a DNW (Deep N-Well) instead of an NMOS transistor with the big channel width as a program select device. Blowing of the proposed cell is done through the parasitic junction formed in the NMOS transistor in the program mode. Sensing failures of '0' data are removed because of removed contact voltage drop of a diode since a NMOS transistor is used instead of the junction diode in the read mode. In addition, a problem of being blown for a non-blown eFuse from a read current through the corresponding eFuse OTP cell is solved by limiting the read current to less than $100{\mu}A$ since a voltage is transferred to BL by using an NMOS transistor with the small channel width in the read mode.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.2
• /
• pp.88-94
• /
• 2011

In this paper, we design a 1-kb OTP (Onetime programmable) memory IP in consideration of BCD process based EM (Electro-migration) and resistance variations of eFuse. We propose a method of precharging BL to VSS before activation of RWL (Read word-line) and an optimized design of read NMOS transistor to reduce read current through a non-programmed cell. Also, we propose a sensing margin test circuit with a variable pull-up load out of consideration for resistance variations of programmed eFuse. Peak current through the non-programmed eFuse is reduced from 728 ${\mu}A$ to 61 ${\mu}A$ when a simulation is done in the read mode. Furthermore, BL (Bit-line) sensing is possible even if sensed resistance of eFuse has fallen by about 9 $k{\Omega}$ in a wafer read test through a variable pull-up load resistance of BL S/A (Sense amplifier).

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.422-429
• /
• 2022

A light sensor chip requires a small capacity eFuse (electrical fuse) OTP (One-Time Programmable) memory IP (Intellectual Property) to trim analog circuits or set initial values of digital registers. In this paper, 128-bit eFuse OTP IP is designed using only 3.3V MV (Medium Voltage) devices without using 1.8V LV (Low-Voltage) logic devices. The eFuse OTP IP designed with 3.3V single MOS devices can reduce a total process cost of three masks which are the gate oxide mask of a 1.8V LV device and the LDD implant masks of NMOS and PMOS. And since the 1.8V voltage regulator circuit is not required, the size of the illuminance sensor chip can be reduced. In addition, in order to reduce the number of package pins of the illumination sensor chip, the VPGM voltage, which is a program voltage, is applied through the VPGM pad during wafer test, and the VDD voltage is applied through the PMOS power switching circuit after packaging, so that the number of package pins can be reduced.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.10
• /
• pp.2359-2368
• /
• 2013

In this paper, an IRD (internal read data) circuit preventing the reentry into the read mode while keeping the read-out DOUT datum at power-up even if noise such as glitches occurs at signal ports such as an input signal port RD (read) when a power IC is on, is proposed. Also, a pulsed WL (word line) driving method is used to prevent a DC current of several tens of micro amperes from flowing into the read transistor of a differential paired eFuse OTP cell. Thus, reliability is secured by preventing non-blown eFuse links from being blown by the EM (electro-migration). Furthermore, a compared output between a programmed datum and a read-out datum is outputted to the PFb (pass fail bar) pin while performing a sensing margin test with a variable pull-up load in consideration of resistance variation of a programmed eFuse in the program-verify-read mode. The layout size of the 8-bit eFuse OTP IP with a $0.18{\mu}m$ process is $189.625{\mu}m{\times}138.850{\mu}m(=0.0263mm^2)$.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.75-77
• /
• 2008

Flexible electronics devices such as plastic display, thin film battery, membrane switch, organic memory for smart card applications will be presented. The performance and power consumption of various display technologies will be compared for OTP requirement in smart cards. Wireless power transmission by RF coupling through an antenna provides a potential power solution to smart cards. Finally, the general trend of smart card future developments will be discussed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.8B
• /
• pp.939-946
• /
• 2011

The Internet banking service provides convenience than the traditional offline services. However, it still causes a number of security problems including hacking. In order to strengthen security, the financial institutions have provided such authentication methods as the official authentication certificate, the security token, the security card and OTP. However, the incidents related to hacking have continuously occurred. Especially, various weak points have been suggested for the authentication methods in regard to such types of hacking as the memory hacking or the MITM attack. So I needed was a new authentication method. In this study, the two-channel authentication method which provide two-way authentication on the user's PC and mobile device when executing the electronic financial transactions in the Internet banking environment is suggested. Also, by analyzing it in comparison with other existing methods, it is possible to check that the prospects of safety and credibility are strengthened.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1877-1886
• /
• 2010

In this paper, we design a redundancy control circuit for 1T-SRAM repair using electrical fuse programming. We propose a dual port eFuse cell to provide high program power to the eFuse and to reduce the read current of the cell by using an external program supply voltage when the supply power is low. The proposed dual port eFuse cell is designed to store its programmed datum into a D-latch automatically in the power-on read mode. The layout area of an address comparison circuit which compares a memory repair address with a memory access address is reduced approximately 19% by using dynamic pseudo NMOS logic instead of CMOS logic. Also, the layout size of the designed redundancy control circuit for 1T-SRAM repair using electrical fuse programming with Dongbu HiTek's $0.11{\mu}m$ mixed signal process is $249.02 {\times}225.04{\mu}m^{2}$.