• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.3
• /
• pp.189-193
• /
• 2015

This paper provides the design techniques of a successive approximation register (SAR) type 12b analog-to-digital converter (ADC) for distributed maximum power point tracking (DMPPT) control in a photovoltaic system. Both a top-plate sampling technique and a $V_{CM}$-based switching technique are applied to the 12b capacitor digital-to-analog converter (CDAC). With these techniques, we can implement a 12b SAR ADC with a 10b capacitor array digital-to-analog converter (DAC). To enhance the accuracy of the ADC, a single-to-differential converted DAC is exploited with the dual sampling technique during top-plate sampling. Simulation results show that the proposed ADC can achieve a signal-to-noise plus distortion ratio (SNDR) of 70.8dB, a spurious free dynamic range (SFDR) of 83.3dB and an effective number of bits (ENOB) of 11.5b with bipolar CMOS LDMOD (BCDMOS) $0.35{\mu}m$ technology. Total power consumption is 115uW under a supply voltage of 3.3V at a sampling frequency of 1.25MHz. And the figure of merit (FoM) is 32.68fJ/conversion-step.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.3
• /
• pp.183-188
• /
• 2015

A 10-bit 10MS/s low power consumption successive approximation register (SAR) analog-to-digital converter (ADC) using a straightforward capacitive digital-to-analog converter (DAC) is presented in this paper. In the proposed capacitive DAC, switching is always straightforward, and its value is half of the peak-to-peak voltage in each step. Also the most significant bit (MSB) is decided without any switching power consumption. The application of the straightforward switching causes lower power consumption in the structure. The input is sampled at the bottom plate of the capacitor digital-to-analog converter (CDAC) as it provides better linearity and a higher effective number of bits. The comparator applies adaptive power control, which reduces the overall power consumption. The differential prototype SAR ADC was implemented with $0.18{\mu}m$ complementary metal-oxide semiconductor (CMOS) technology and achieves an effective number of bits (ENOB) of 9.49 at a sampling frequency of 10MS/s. The structure consumes 0.522mW from a 1.8V supply. Signal to noise-plus-distortion ratio (SNDR) and spurious free dynamic range (SFDR) are 59.5 dB and 67.1 dB and the figure of merit (FOM) is 95 fJ/conversion-step.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.609-612
• /
• 1998

Pyroelectric properties of rhombohedral $Pb(ZrxTi_1-x)O_3ceramics$ with various Zr/Ti ratios of 84/16, 87/13, 90/10, and 93/7 are investigated using dynamic method. The response characteristics of PZT samples are examined by considering frequency dispersion. Since the reorientation of the grain does not the influence on the increase of frequency at low frequency (2~200Hz), the maximum pyroelectric response can be obtained with the change of spontaneous polarization. However, the pyroelectric response of PZT samples could be reduced as the spontaneous polarization decreases due to the restrain of the reorientation of the grain with the increasing of requency at high frequency (200~2000Hz). We have obtained the good pyroelectric response in the PZT sample having 84/16 Zr/Ti ratio, then the pyroelectric coefficient (${\gamma}$) and the figure of merit (FV) were $17.3nC/\textrm{cm}^2K$ and 2.28$\times$10-11Ccm/J, respectively. The noise equivalent power (NEP), the detectivity (D*) were 1.21$\times$10-7W/Hz$\frac{1}{2}$ and 8.26$\times$106cmHz$\frac{1}{2}$/W, respectively.

• Proceeding of Spring/Autumn Annual Conference of KHA
• /
• 2009.11a
• /
• pp.213-216
• /
• 2009

The purpose of this study is analyzing temporal flow about 20 detailed performance items in the "Housing Performance Grading Indication System". This study try to figure out situations according grade in detailed performance item and to analyze change item about 112 cases(2 cases in 2006, 15 cases in 2007, 46 cases in 2008, 49 cases in 2009), from January 9, 2006 which system is undertaken, to October, 2009. This system consists of 5 main performance section, 14 performance categories and 20 detailed performance items. 5 main performance parts are Noise and Acoustics(Light-weight impact sound control, heavy-weight impact sound control, sound control of toilet, sound control of party wall), Long-life(flexibility, remodeling & maintenance, durability), Landscape & Indoor Environment(landscape, formaldehyde control & ventilation, daylighting, thermal environment), Welfare & Barrier-free(playground and community center, welfare space, barrier-free design), Fire Safety(fire safety, safe place, fire-resisting quality). Total efficiency about housing can understand systematically of 20 perfomance items though this research.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.148-156
• /
• 2003

This paper describes the RF performance issues of UE for W-CDMA system based on 3 GPP specifications. The parameters of transmitter and receiver are derived from the viewpoint of RF performance. In order for UE to achieve high performance, the transceiver performance requirements such as ACLR, EVM, Peak Code Domain Error, spectrum emission mask, frequency error stability and TX power control dynamic range for transmitter and reference sensitivity level, blocking characteristics, noise figure, ACS, AGC dynamic range for receiver are considered. On the basis of the required parameters, the UE RF transceiver is implemented and then the evaluation of RF performance is accomplished through practical test scenarios.

• Journal of the Institute of Convergence Signal Processing
• /
• v.12 no.3
• /
• pp.217-221
• /
• 2011

GaAs-based and InP-based HEMTs(High Electron Mobility Transistors) have good microwave and millimeter-wave frequency performance with lower minimum noise figure. GaAs-based MHEMTs(Metamorphic HEMTs) have some advantages, especially for cost, compared with InP-based ones. In this paper, the RF small-signal circuits of MHEMTs are simulated and analyzed for the design of millimeter-wave application systems. The simulation analysis for RF small-signal frequency can help and give some insights about the MHEMTs for the design of millimeter-wave application and communication systems.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.39-49
• /
• 1999

This paper describes the development of a vision-aided position and orientation recognition system for automatically adjusting electronic tuners which control the waveform by rotating variable resisters. The position and orientation recognition system estimates the center and the angle of the tuner grooves so that the main controller may correct the difference from the ideal position and thereby manipulate the variable resisters automatically. In this paper a robust algorithm is suggested which estimates the center and the angle of the tuner grooves fast and precisly from the source image with lighting variance and video noise. In the algorithm morphological filtering, 8-chain coding, and invariant moments are sequentially used to figure out image segments concerned. The performance of the proposed system was evaluated using a set of real specimens. The results indicate the system works well enough to be used practically in real manufacturing lines. If the system adopts a high speed frame grabber which enables real time image processing, it can also be applied to positioning of robot manipulators as well as automated PCB adjusters.

• Korean Journal of Optics and Photonics
• /
• v.21 no.4
• /
• pp.139-145
• /
• 2010

A complete modeling of erbium-doped Bismuth-oxide fibers with a high doping concentration is presented. A 6-level amplifier system that incorporated clustering-induced concentration quenching, cooperative upconversion, pump excited state absorption (ESA), and signal ESA, was adopted for the modeling. The accuracy of the modeling was verified by comparing the calculated gain and noise figure with experimentally obtained ones.

• Korean Journal of Optics and Photonics
• /
• v.12 no.3
• /
• pp.200-204
• /
• 2001

The structural design and the measured characteristics of optical signal amplification unit for 640 Gbps (10 Gbps$\times$64 ch.) WDM transmission systems are reported. The unit is composed of two sub gain block units for the amplification of C-band (1530-1560 nm) and L-band (1570-1600 nm), respectively. Programmable microprocessors monitor the states of operation and optimize the optical output conditions. Each sub gain block unit can maintain total optical output power of +21 dBm with gain flatness of < 1 dB and noise figure of <7.2 dB for the input power in the dynamic range from-5 to +1 dBm.+1 dBm.

• 한국정보통신설비학회:학술대회논문집
• /
• 2003.08a
• /
• pp.143-148
• /
• 2003

In this paper, we focused on the performance of reverse link in 1.8GHz CDMA 1x system including the Tower-Mount LNA in an urban environment. In order to study the benefit of TMLNA, Hata model is used and the effects of multiple cells are considered. Cell coverage extension ratio is proportional to the increased gain of TMLNA in CDMA cell site. However the cell coverage is not extended even if the noise figure of TMLNA is reduced in an urban area. When typical RSSI is between -70dBm and -80dBm, the increased gain and the reduced NF of TMLNA are not impact to the pole capacity of cell site. Namely, the benefit of TMLNA in an urban area is not the problem of capacity but the proble of sensitivity. The results are also shown that reverse link $E_b/N_o$ is improved by minimum 5dB and BER is lower than $10^{-6}$.