• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.104-110
• /
• 2006

The advantage of the DSM which employ multi-bit quantizer is the increased SNR at the modulator's output. Typically 6 dB improvement is effected for every one additional bit. But multi-bit quantizer evidently requires multi-bit DAC in the feedback loop. The integral linearity error of the feedback DAC has direct impact upon the system performance and degraded SNR of the system. In order to mitigate the negative impact the DAC has on the system performance, many DEM(Dynamic Element Matching) schemes has been proposed. Among the proposed schemes, four schemes(DER,CLA,ILA,DWA) are explained and its performance has been compared. DWA(Data Weighted Averaging) method shows the best performance of the all.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.420-423
• /
• 2015

This paper proposes a method of non-linearity error detection and calibration for binary-weighted charge-driven DACs. In general, the non-linearity errors of DACs often occur due to the mismatch of layout designs or process variation, even when careful layout design methods and process calibration are adopted. Since such errors can substantially degrade the SNDR performance of DAC, it is crucial to accurately measure the errors and calibrate the design mismatches. The proposed method employs 2 identical DAC circuits. The 2 DACs are sweeped, respectively, by using 2 digital input counters with a fixed difference. A comparator identifies any non-linearity errors larger than an acceptable discrepancy. We also propose a calibration method that can fine-tune the DAC's capacitor sizes iteratively until the comparator finds no further errors. Simulations are presented, which show that the proposed method is effective to detect the non-linearity errors and calibrate the capacitor mismatches of a 12-bit DAC design of binary-weighted charge-driven structure.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.149-155
• /
• 2015

This paper proposes 5-MS/s 10-bit digital-to-analog converter(DAC) with the improved linearity. The proposed DAC consists of a 10-bit R-2R-based DAC, an output buffer using a differential voltage amplifier with rail-to-rail input range, and a band-gap reference circuit for the bias voltage. The linearity of the 10-bit R-2R DAC is improved as the resistor of 2R is implemented by including the turn-on resistance of an inverter for a switch. The output voltage range of the DAC is determined to be $2/3{\times}VDD$ from an rail-to-rail output voltage range of the R-2R DAC using a differential voltage amplifier in the output buffer. The proposed DAC is implemented using a 1-poly 8-metal 130nm CMOS process with 1.2-V supply. The measured dynamic performance of the implemented DAC are the ENOB of 9.4 bit, SNDR of 58 dB, and SFDR of 63 dBc. The measured DNL and INL are less than +/-0.35 LSB. The area and power consumption of DAC are $642.9{\times}366.6{\mu}m^2$ and 2.95 mW, respectively.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2018.05a
• /
• pp.484-485
• /
• 2018

DAC 는 디지털-아날로그 변환 회로는 디지털 전기 신호를 아날로그 전기 신호로 변환하는 전자 회로이다. 특히 최근 음성 신호는 그 효율성 및 경제성 때문에 디지털 데이터 형태로 저장/전송되고 있어 DAC 는 음성 관련 사업에서 필수적으로 쓰이고 있다. 본 논문은 음성 신호의 디지털-아날로그 변환 시 DAC 의 성능에 대한 분석 및 시험 결과를 소개한다.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.47-52
• /
• 2017

In this paper, CMOS SAR A/D converter 1.8V supply for the design of an A/D converter having an middle speed for the biological signal processing was designed. This paper proposes design of a 10-bit SAR Analog to Digital Converter improving linearity driven by MSB node of C-DAC array divided into 4 equal parts. It enhances linearity property, by retaining the analog input signal charging time at MSB node. Because MSB node samples analog input, it enhances resolution through getting initial input signal precisely. By using split capacitor on C-DAC array, it reduced chip size and power dissipation. The Proposed SAR A/D Converter is fabricated in 0.18um CMOS and measured 7.5 bits of ENOB at sampling frequency 4MS/s and power supply of 1.8V. It occupies a core area of $850{\times}650um^2$ and consumes 123.105uW. Therefore it results in 170.016fJ/step of FOM(Figure of Merit).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.68 no.1
• /
• pp.90-97
• /
• 2019

The charge redistribution digital-to-analog converter(CR-DAC) is often used for successive approximation register analog-to-digital converter(SAR ADC) that requiring low power consumption and small circuit area. However, CR-DAC is required 2 to the power of N unit capacitors to generate reference voltage for successive approximation of the N-bit SAR ADC, and many unit capacitors occupy large circuit area and consume more power. In order to improve this problem, this paper proposes SAR ADC using series capacitor DAC. The series capacitor DAC is required 2(1+N) unit capacitors to generate reference voltage for successive approximation and charges only two capacitors of the reference generation block. Because of these structural characteristics, the SAR ADC using series capacitor DAC can reduce the power consumption and circuit area. Proposed SAR ADC was designed in CMOS 180nm process, and at 1.8V supply voltage and 500kS/s sampling rate, proposed 6-bit SAR ADC have signal-to-noise and distortion ratio(SNDR) of 36.49dB, effective number of bits(ENOB) of 5.77-bit, power consumption of 294uW.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.61-66
• /
• 2005

This paper describes a 10-bit 210MHz CMOS current-mode Digital-to-Analog Converter (DAC) consisting of 6 bit MSB current cell matrix Sub-DAC, 2 bit mSB unary current source Sub-DAC, and 2 bit LSB binary weighting Sub-DAC for Wireless LAN application. A new deglitch circuit is proposed to control a crossing point of signals and minimize a glitch energy. The proposed 10-bit CMOS current mode DAC was designed by a $0.35{\mu}m$ CMOS double-poly four-metal technology rate of 210MHz, DNL/INL of ${\pm}0.7LSB/{\pm}1.1LSB$, a glitch energy of $76pV{\cdot}sec$, a SNR of 50dB, a SFDR of 53dB at 200MHz sampling clock and power dissipation of 83mW at 3.3V

• 전자공학회논문지 IE
• /
• v.43 no.3
• /
• pp.6-12
• /
• 2006

This paper described an 8bit, 100Msample/s CMOS D/A converter using a glitch-time minimization technique for the high-speed sampling rate of 100MHz level. The proposed DAC was implemented in $0.35{\mu}m$ Hynix CMOS technology and adopts a current mode architecture to optimize sampling rate, resolution, chip area. The DAC linear characteristics was similar to the proposed specification and the prototype error between DNL and INL is less than $\pm$0.09LSB respectively. Also, the manufactured DAC chip was analyzed the cause of error operation and proposed the field considerations for chip test.

• Journal of IKEEE
• /
• v.22 no.4
• /
• pp.1012-1018
• /
• 2018

In this paper, CMOS SAR (Successive Approximation Register) A/D converter with 1.8V supply voltage is designed for IoT sensor processing. This paper proposes design of a 12-bit SAR A/D converter with two A / D converters in parallel to improve the sampling rate. A/D converter1 of the two A/D converters determines all the 12-bit bits, and another A/D converter2 uses the upper six bits of the other A/D converters to minimize power consumption and switching energy. Since the second A/D converter2 does not determine the upper 6 bits, the control circuits and SAR Logic are not needed and the area is minimized. In addition, the switching energy increases as the large capacitor capacity and the large voltage change in the C-DAC, and the second A/D converter does not determine the upper 6 bits, thereby reducing the switching energy. It is also possible to reduce the process variation in the C-DAC by proposed structure by the split capacitor capacity in the C-DAC equals the unit capacitor capacity. The proposed SAR A/D converter was designed using 0.18um CMOS process, and the supply voltage of 1.8V, the conversion speed of 10MS/s, and the Effective Number of Bit (ENOB) of 10.2 bits were measured. The area of core block is $600{\times}900um^2$, the total power consumption is $79.58{\mu}W$, and the FOM (Figure of Merit) is 6.716fJ / step.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.225-228
• /
• 2012

In this paper, a 10-bit digital-to-analog converter (DAC) with small area is proposed. The 10-bit DAC consists of a 8-bit decoder, a 2-bit time-interpolator, and a buffer amplifier. The proposed time-interpolation is achieved by controlling the charging time through a low-pass filter composed of a resistor and a capacitor. To implement the accurate time-interpolator, a control pulse generator using a replica circuit is proposed to minimize the effect of the process variation. The proposed 10-bit Time-Interpolation DAC occupies 61 % of the conventional 10-bit resistor-string DAC. The proposed DAC is designed using a $0.35{\mu}m$ CMOS process with a 3.3 V supply. The simulated DNL and INL are +0.15/-0.21 LSB and +0.15/-0.16 LSB, respectively.