• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.4
• /
• pp.275-279
• /
• 2004

A new burst mode clock and data recovery circuit is realized that improves the previousldy-known gated-oscilletor technique with half rate clock recovery, The circuit was fabricated with 0.25um CMOS technology, and its functions were confirmed up to 1 Gbps.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.4
• /
• pp.188-193
• /
• 2003

This paper describes a novel burst-mode clock and data recovery (CDR) circuit which can be used for 622Mbps burst mode applications. The CDR circuit is basically a phase locked loop (PLL) having two phase detectors (PDs), one for the reference clock and the other for the NRZ data, whose operations are controlled by an external control signal. This CDR was fabricated in a 1-poly 5-metal $0.25{\;}\mu\textrm{m}$ CMOS technology. Jitter generation, burst/continuous mode data receptions were tested. Operational frequency range is 320Mhz~720Mhz and BER is less than 1e-12 for PRBS31 at 622Mhz. For the same data sequence, the extracted clock jitter is less than 8ps rms. Power consumption of 100mW was measured without I/O circuits.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.8A
• /
• pp.644-649
• /
• 2003

Novel 622Mb/s burst-mode clock and data recovery (CDR) circuits with muxed oscillators are realized for passive optical network (PON) application. The CDR circuits are implemented with 0.35$\mu\textrm{m}$ CMOS process technology. Lock is accomplished on the first data transition and data are sampled in the optimal point. The experimental results show that the proposed CDR circuits recover the incoming 400Mbps-680Mbps burst mode input data without error.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.858-864
• /
• 2019

A clock system is proposed to eliminate data loss due to frequency difference between sensor nodes in a sensor utility network. The proposed clock system for each sensor node consists of a bust clock-data recovery (CDR) circuit, a digital phase-locked loop outputting a 32-phase clock, and a digital frequency synthesizer using a programmable open-loop fractional divider. A CMOS oscillator using an active inductor is used instead of a burst CDR circuit for the first sensor node. The proposed clock system is designed by using a 65 nm CMOS process with a 1.2 V supply voltage. When the frequency error between the sensor nodes is 1%, the proposed burst CDR has a time jitter of only 4.95 ns with a frequency multiplied by 64 for a data rate of 5 Mbps as the reference clock. Furthermore, the frequency change of the designed digital frequency synthesizer is performed within one period of the output clock in the frequency range of 100 kHz to 320 MHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.21-26
• /
• 2008

In this paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuits are implemented with 0.35um CMOS process technology. Locking dynamics is accomplished with instantaneous feature and data are sampled at an optimal timing. This is realized by seven different delay configurations, which are generated from precisely-controlled delay buffers. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.57-63
• /
• 2009

In this Paper, a novel 622Mbps burst-mode clock and data recovery (CDR) circuit is proposed for passive optical network (PON) applications. The CDR circuit is composed of CDR(Clock and Data Recovery) block and PLL(Phase Locked Loop) block. Lock dynamics is accomplished on the first data transition and data are sampled in the optimal point. The CDR circuit is realized in 0.35um CMOS process technology. With input pseudo-random bit sequences(PRBS) of $2^7-1$, the simulations show 17ps peak-to-peak retimed data jitter characteristics. The experimental results show that the proposed CDR circuits are operating as expected, recovering an incoming 622Mbps burst-mode input data without errors.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.87-95
• /
• 2013

In this paper, 2.5 Gb/s burst-mode clock and data recovery(CDR) is presented. Digital frequency calibration scheme is adopted to eliminate mismatch between the input data rate and the output frequency of the gated voltage controlled oscillator(GVCO) in the clock recovery circuitry. A jitter rejection scheme is also used to reduce jitter caused by input data. The proposed burst-mode CDR is designed using 0.11 ${\mu}m$ CMOS technology. Post-layout simulations show that peak-to-peak jitter of the recovered data is 14 ps with 0.1 UI input referred jitter, and maximum tolerance of consecutive identical digit(CID) is 2976 bits without input data jitter. The active area occupies 0.125 $mm^2$ without loop filter and the total power consumption is 94.5 mW.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.4 no.2
• /
• pp.29-36
• /
• 2005

All-optical fiber-type $2{\times}32$ splitters for an Ethernet PON (passive optical network) were fabricated by using a FBT (fiber biconical tapered) process and the performance of the splitters was tested in upstream transmission of the EPON system. The $2{\times}32$ splitters was obtained by cascading $1{\times}4$ splitters fabricated by a conventional FBT process and showed -18 dB of insertion loss with 1.5 dB uniformity of output power at each channel and -0.1 dB of polarization dependent loss. The insertion loss variation was below 0.1 dB at the temperature range of $-40^{\circ}C\;to\;80^{\circ}C$. For upstream channel transmission test in the EPON system were a Zig board and a burst mode receiver. Zenko-made optical module was used for the burst mode receiver by adding functions of serializer/deserializer and clock data recovery, a Virtex II pro20 chipset and Vitesse VSC7123 were used in the Zig board for characterizing the burst mode and in the clock data recovery chipset, respectively. Startup acquisition lock time and data acquisition lock time were measured to be 670ns and 400ns, respectively, in the upstream channel transmission of the EPON system adapting the $2{\times}32$ splitter fabricated in this work.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.12
• /
• pp.1-9
• /
• 2001

In the APON(ATM Passive Optical Network), the transmission of the upstream traffic is based on a TDMA(Time Division Multiple Access) method that an OLT(Optical Line Termination) permits ONUs(Optical Network Units) sending cells by allocating time slots. Because the upstream is not a streaming mode, the cell synchronizer has to be operated in the burst mode. Also, the cell phase monitor is required to prevent collisions between cells which are transmitted by multiple ONUs through a single optical fiber. In this paper, a TDMA burst cell synchroniser is implemented with the FPGA(Field Programmable Gate Array) being used in the APON based on G.983.1 for transmitting upstream cells. It has two main functions which are the upstream data recovery and the phase monitoring. The former is to recover the upstream data and clock in the OLT by seeking the preamble which is the overhead of the upstream time slot and by aligning the phase of the bit and cell with the system clock. The latter is to provide the information to the ONU to compensate for the equalization delay by monitoring continuously the phase difference between adjacent cells to avoid the cell collision on the upstream.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.167-174
• /
• 2012

The circuits including with Optical transceiver and clock data recovery, in this paper, SERDES (SERializer-DESerializer) are implemented to construct a GE-PON burst-mode transceiver supporting IEEE 802.3ah and a jig for measuring the burst-mode characteristics, that is to say, PON upstream optical transmission environment are manufactured to evaluate the performance of transceiver. we verified that the limiting amplifier compensated the gap of max. 26dB optical power by experiments. The startup acquisition lock time is 670ns in case of using VSC7123 and 2300ns in case of S2060 and the data acquisition lock time were measured to be 400ns and 600ns, respectively, in the upstream channel transmission in this work. While on the other, VSC7123 is satisfied with IEEE802.3ah recommendations.