• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1551-1561
• /
• 2014

Design, Simulation and experimental analysis of closed loop time domain based Discrete PWM buck-boost converter are described. To improve the transient response and dynamic stability of the proposed converter, Discrete PID controller is the most preferable one. Discrete controller does not require any precise analytical model of the system to be controlled. The control system of the converter is designed using digital PWM technique. The proposed controller improves the dynamic performance of the buck-boost converter by achieving a robust output voltage against load disturbances, input voltage variations and changes in circuit components. The converter is designed through simulation using MATLAB/Simulink and performance parameters are also measured. The discrete controller is implemented, and design goal is achieved and the same is verified against theoretical calculation using LabVIEW.

• The KIPS Transactions:PartA
• /
• v.9A no.1
• /
• pp.93-98
• /
• 2002

This paper introduces the design of high-speed analog-to-digital converter (ADC) for hard disk drive (HDD) read channel applications. This circuit is bated on fast regenerative autozero comparator for high speed and low-error rate comparison operation, and Double Speed Dual ADC (DSDA) architecture for efficiently increasing the overall conversion speed of ADC. A new type of thermometer-to-binary decoder appropriate for the autozero architecture is employed for no glitch decoding, simplifying the conventional structure significantly. This ADC is designed for 6-bit resolution, 800 Msample/s maximum conversion rate, 390 mW power dissipation, one clock cycle latency in 0.65 m CMOS technology.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.47-52
• /
• 2017

In this paper, CMOS SAR A/D converter 1.8V supply for the design of an A/D converter having an middle speed for the biological signal processing was designed. This paper proposes design of a 10-bit SAR Analog to Digital Converter improving linearity driven by MSB node of C-DAC array divided into 4 equal parts. It enhances linearity property, by retaining the analog input signal charging time at MSB node. Because MSB node samples analog input, it enhances resolution through getting initial input signal precisely. By using split capacitor on C-DAC array, it reduced chip size and power dissipation. The Proposed SAR A/D Converter is fabricated in 0.18um CMOS and measured 7.5 bits of ENOB at sampling frequency 4MS/s and power supply of 1.8V. It occupies a core area of $850{\times}650um^2$ and consumes 123.105uW. Therefore it results in 170.016fJ/step of FOM(Figure of Merit).

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.237-243
• /
• 2015

In this paper, we consider a cascaded type of control architecture for a multi motor-based feedback control system and propose an ADC (Analog to Digital Converter) resource allocation method to efficiently utilize the limited ADC resources. The purpose of the resource allocation method is to minimize both the motor position measurement error and the d-q current measurement error. The cascaded type of control architecture is applied in parallel to each motor to independently control the speed of a motor in the multi motor control system. All the control algorithms are implemented by software using a single microcontroller without using additional microcontrollers. It is illustrated by experiments that the speed and the torque of each motor are controlled precisely by the proposed control architecture with the efficient ADC allocation method.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.533-536
• /
• 2004

In this paper, CMOS A/D converter with 10bit 32MSPS at 3.3V is designed for HPNA 2.0. In order to obtain the resolution of 10bit and the character of high-speed operation, we present multi-stage type architecture. That consist of sample and hold(S&H), 4bit flash ADC and 4bit Multiplier D/A Converter (MADC) also the Overflow and Underflow for timing error correct of Digital Correct ion Logic (DCL). The proposed ADC is based on 0.35um 3-poly 5-metal N-well CMOS technology. and it consumes 130mW at 3.3V power supply.

• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.77-86
• /
• 2009

A wavelet Electrocardiogram(ECG) detector and its analog-to-digital converter(ADC) for low-power implantable cardiac pacemakers are presented in this paper. The proposed wavelet-based ECG detector consists of a wavelet decomposer with wavelet filter banks, a QRS complex detector of hypothesis testing with wavelet-demodulated ECG signals, and a noise detector with zero-crossing points. To achieve high-detection performance with low-power consumption, the multi-scaled product algorithm and soft-threshold algorithm are efficiently exploited. To further reduce the power dissipation, a low-power ADC, which is based on a Successive Approximation Register(SAR) architecture with an on/off-time controlled comparator and passive sample and hold, is also presented. Our algorithmic and architectural level approaches are implemented and fabricated in standard $0.35{\mu}m$ CMOS technology. The testchip shows a good detection accuracy of 99.32% and very low-power consumption of $19.02{\mu}W$ with 3-V supply voltage.

• Journal of Advanced Navigation Technology
• /
• v.3 no.1
• /
• pp.52-59
• /
• 1999

Digital microwave wideband receiver including linear amplifier, analog-to-digital converter(ADC) and digital signal processor is able to analyze its performance using sensitivity and dynamic range of system. Determination of gain, third-order intermodulation products and ADC characteristics and design criteria for the linear amplifier chain is essential problem for sensitive and dynamic range. Also, if there are two signals with frequencies very close, digital signal processor must be able to separate the two signals. In this paper, we measured dynamic range as gain was changed and determined gain value for the proper sensitivity and dynamic range and high resolution spectrum estimation was used to separate two close signals.

• Journal of IKEEE
• /
• v.17 no.3
• /
• pp.234-240
• /
• 2013

This paper presents an incremental delta-sigma analog-to-digital converter (ADC) for a single-electrode capacitive touch sensor. The second-order cascade of integrators with distributed feedback (CIFB) delta-sigma modulator with 1-bit quantization was fabricated by a $0.18-{\mu}m$ CMOS process. In order to achieve a wide input range in this incremental delta-sigma analog-to-digital converter, the shielding signal and the digitally controlled offset capacitors are used in front of a converter. This circuit operated at a supply voltage of 2.6 V to 3.7 V, and is suitable for single-electrode capacitive touch sensor for ${\pm}10-pF$ input range with sub-fF resolution.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.5
• /
• pp.312-320
• /
• 2003

This work describes an 8b 200 MHz 0.18 urn CMOS analog-to-digital converter (ADC) based on a pipelined architecture for flat panel display applications. The proposed ABC employs an improved bootstrapping technique to obtain wider input bandwidth than the sampling tate of 200 MHz. The bootstrapuing technique improves the accuracy of the input sample-and-hold amplifier (SHA) and the fast fourier transform (FFT) analysis of the SHA outputs shows the 7.2 effective number of bits with an input sinusoidal wave frequency of 500 MHz and the sampling clock of 200 MHz at a 1.7 V supply voltage. Merged-capacitor switching (MCS) technique increases the sampling rate of the ADC by reducing the number of capacitors required in conventional ADC's by 50 % and minimizes chip area simultaneously. The simulated ADC in a 0.18 um n-well single-poly quad-metal CMOS technology shows an 8b resolution and a 73 mW power dissipation at a 200 MHz sampling clock and a 1.7 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5C
• /
• pp.395-402
• /
• 2008

In this paper, an I/Q channel 12bits 40MS/s Pipeline Analog to Digital Converter that is able to apply to WLAN/WMAN system is proposed. The proposed ADC integrates DLL based duty-correction circuit which corrects the fluctuations in the duksty cycle caused by miniaturization of CMOS devices and faster operating speeds. It is designed as a 1% to 99% input clock duty cycle could be corrected to 50% output duty cycle. The prototype ADC is implemented in a $0.18{\mu}m$ CMOS n-well 1-poly 6-metal process and dissipates 184mW at 1.8V single supply The SNDR of the proposed 12bit ADC is 52dB and SFDR of 59dBc(@Fs=20MHz, Fin=1MHz) is measured.