Understanding of wear mode and prediction of wear rate of parts in sliding contact are very important in field of meterial design relating with wear resistant. This paper has been undertaken to analyze the possibility of elucidation of wear mode and prediction of wear rate for annealed steel in sliding contact using the X-ray diffraction. The sliding wear test with various velocities using pin-on-disc machine and the X-ray diffraction test on the worn surface have been carried out. The results have been shown that the magnitude of residual stress and half-value breadth on the worn surface have a good correlation with wear mode. The difference between before and after test of half-value breadth on worn surface has been shown to be exponential relation with wear rate in the same wear mode.

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear in the root and the tip of tooth and tooth edge.

Friction and wear test was performed for nylon, acetal resin, and PTFE(polytetrafluoroethylene) under reciprocating dry sliding conditions against a steel counterpart. Friction coefficient and specific wear rate were analysed as a function of sliding distance and applied load. The worn surfaces of plate and disc specimens were observed using SEM(Scanning Electron Microscopy). The experimental results show that acetal resin exhibited lowest wear rates whereas PTFE possessed lowest friction coefficient. The prominent wear mechanisms found were adhesion and abrasion.

An experimental study was performed to discover the effect of environment on the tribological behavior of Si-incorporated diamond-like carbon(Si-DLC) film slid on a steel ball. The films were deposited on Si(100) wafers from radio-frequency glow discharge of mixtures of benzene and dilute silane gases. Experiments using a ball-on-disk test-rig was performed under vacuum, dry air and ambient air conditions. It was observed that coefficient of friction was decreased as the environmental condition changes from vacuum, to dry air. It was also observed that the coefficient of friction decreased with increasing silicon concentration in the film. Chemical analyses of debris suggested that the low and stable friction coefficient is closely related to the silicon rich oxide debris and the rolling action.

A material was formulated with Phenol novolac and HEXA only. The cure kinetics and thermal characteristics of phenol novolac with various HEXA contents were peformed by differential scanning calorimetry and thermal gravimetric analysis. All kinetic parameters of the curing reaction including the reaction order, activation energy, and rate constant were calculated and reported. The results indicate that the curing reaction goes through an autocatalytic kinetic mechanism. The friction and wear characteristics of this material were determined using friction material testing machine. The friction coefficient of phenol novolac with various HEXA contents was determined using the PV(pressure & velocity) factor. The most stable and highest friction coefficient with a various pressure and velocity condition was found at HEXA 10 wt.% material. The specific wear rate per unit sliding distance with a various HEXA contents was reported.

The effect of the microstructure of gray cast iron on friction properties was investigated by using a pad-on-disk type friction tester. Cast iron samples used in this investigation were obtained from "step block" castings, which were designed to produce microstructure with different graphite flake morphologies from different cooling rate and solidification rate. Results of this work showed that the gray cast iron disks with long graphite flakes showed less fading. The rotors containing smaller amounts of ferrite showed higher friction coefficient and better fade resistance than others.an others.

Surface hardening of plain carbon steel (SM45C) by Laser are usually much finer and stronger than those of the base metals. The present study was under taken to investigate the wear resistance and a processing parameters such as, power density, pulse width, defocusing distance, and molten depth for surface modification of plain carbon steel. The wear test was carried out under experimental condition using the wear test device, and in which the annular surfaces of wear test specimens as well as mating specimen of alumina ceramics($Al_2O_3$) was rubbed in dry sliding condition. It is shown that molten depth and width depend on defocusing distance. The wear loss on variation of sliding speed was much in lower speed range below 0.2m/sec and in higher speed range above 0.7m/sec, but wear loss was little in intermediate speed range. It depends on oxidation speed and wear speed.

The fretting wear characteristics of STS304 steel in seawater were investigated experimentally. A fretting wear tester was designed to be suitable for this fretting test. This study was focused on the effects due to the combination of normal load, slip amplitude and number of cycles and corrosive environment as the main factors of fretting. The results of this study showed that the wear volume increased abruptly at slip amplitude between 70${\mu}{\textrm}{m}$~ 100${\mu}{\textrm}{m}$ by fracture of oxide layers but above that slip amplitude the wear volume increased steadily.

Fretting Wear Behavior and Characteristics were investigated with Inconel 690 tube which is used in Nuclear Power Plant. Fretting Wear Tester has been engaged in the study of characteristics on tube fretted induced to various factors, i.e. vibration amplitude, contact type, material properties load support geometry, environmental effect Test has been performed in air and at room temperature. Wear volume rate has been approximately estimated as a function of normal load.

Sliding friction and wear tests for silicon nitride(Si$_3$N$_4$) was carried out with a ball-on-disk specimen configuration. The material used in this study was HIPed silicon nitride. The tests was carried out from room temperature to 1000"I with self mated couples of slicon nitride in laboratory air. Worn surfaces were observed by SEM and debris particles from worn surfaces were analyzed degree of oxidation by XPS. XPS.

The friction and wear behavior of MoS$_2$Coatings were investigated using a pin and disk type tester. The experiment was conducted using silicon nitride as pin material and MoS$_2$-on-bearing steel as disk material under different operating conditions that include linear sliding speeds in the range of 22~66mm/sec, normal loads varying from 9.8~29.4N, corresponding to maximum contact pressure of 1.78~2.830GPa and atmospheric conditions of high vacuum, medium vacuum, ambient air. The results showed that low friction coefficient of the coating has been identified when running in high vacuum and that friction coefficient and wear volume increased with increasing normal load. Also at high load conditions, the friction coefficient and wear volume increased with increasing sliding velocity.

Point contact film thickness in elastohydrodynamic lubrication (EHL) is analyzed by the image processing method for the monochromatic incident light. Interference between the reflected lights both on Cr coating of glass disk and on super finished ball makes circular fringes, which are regarded as film thickness together with numbering of fringe order. In this study, we developed technology to measure the film thickness by analyzing dark and bright intensity waves which results from monochrome green light. Two typical fringe patterns only with intensity values 3re examined for the measurement of point contact EHL film thickness. We expect that this technology will give valuable clue to improve color image processing analysis for high resolution of EHL film thickness with white incident light.

It is possible for a volume of fluid to become trapped in the space between two adjoining teeth and the tips of the teeth engage in Gear Pumu with involute teeth. This trapped fluid leads to several harmful results, for example fluctuating pressure and aeration of pump. In this study, hence, theoretical and experimental analyses on this 'Trapping' were accomplished as using relief port, one of the means for avoiding it. Also, the grasp and analysis on variational type of the internal pressure in parallel with above experiments are achieved so that hydrodynamic behaviors in pump were contemplated.

In this study, a numerical procedure to analyze 3-dimensional unsteady elastohydrodynamic lubrication was developed. The procedure was applied to the actual cam and roller follower of the valve mechanism for a marine diesel engine. The pressure distribution between the cam and roller follower was calculated for the several cam rotating angles. The pressure spike is shown near the roller edge and it is getting higher as the external load is increased. The roller profile for reducing the pressure spike was suggested by the Hertzian contact analysis.

A numerical analysis between the piston and cylinder in swash plate type hydraulic piston pumps under reciprocating motion is presented. A finite difference method and the Newton-Raphson method are used simultaneously to solve the Reynolds equation In the clearance and the equation of motion for the piston. The tapered piston showed stable behaviors regardless of their initial eccentric conditions in the clearance and the reciprocating speed affect highly on the piston end trajectories. Therefore, the results of present study can be used other types fluid machineries.

This paper describes the surface roughness effect in parallel thrust bearing. In mixed lubrication, some contacts will take place between asperities, and partial lubrication will occur. An average Reynolds Equation is utilized to determine effects of surface roughness on partially lubricated contacts. By using an autocorrelation function for the surface profile, surface model is generated numerically Although the two surfaces are parallel in thrust bearing separated by thin film, the pressure peak is formed due to asperites. By means of surface profile parameters, it is shown that which surface is optimal for the parallel thrust bearing.

A numerical dynamic simulation is necessary to investigate the capacity of the HDD. The slider surface become more and more complicated to make the magnetized area smaller and readback signal stronger. So a numerical dynamic simulation must be preceded to develop a new slider in HDD. The dynamic simulations of air-lubricated slider bearing have been peformed using FIFD(Factored Implicit Finite Difference) method. The governing equation, Reynolds equation Is modified with Fukui and Kaneko model(FK model) which includes the first and the second-order slip. The equations of motion for the slider bearing are solved simultaneously with the modified Reynolds equation for the case of three degrees of freedom. The slider transient response for disk step bump and slider impulse force is given for various case and for iteration algorithm and new algorithm.

Silicon nitride ceramic has been verified as an excellent rolling bearing material because of its high strength and outstanding rolling fatigue life properties. However under some corrosive circumstances it showed drawbacks such as hardness reduction and severe wear caused by corrosion. In this work, the variations of the rolling wear and hardness of three kinds of ceramics were studied for the specimen aged 15 days in alkali water (90$\pm$2$^{\circ}C$, 25 wt% NaOH). All of the specimens, \circled1Si$_3$N$_4$, \circled23Y-TZP and \circled33Y-TZP alloyed with 5 wt% CeO$_2$, were sintered and post-Hipped, and then polished up to 0.02 ${\mu}{\textrm}{m}$Ra of surface roughness. Rolling wear tests were conducted by MJ type rolling fatigue life tester under the initial theoretical maximum contact stress or 3.76 Gra and the spindle speed of 1,000 rpm. Spindle oil was used as a lubricant. The specimens were not worn before aging. For the specimen aged in alkali water, Si$_3$N$_4$and 3Y-TZP were worn by rolling wear tests, and hardness was decreased. While aging the specimens, the phase was transformed from tetragonal to monoclinic in 3Y-TZP and the microstructure change occurred in Si$_3$N$_4$. 3Y-TZP alloyed with 5 wt% CeO$_2$specimens were not worn after aging and no phase transformation occurred while aging.

Nonlinear characteristics of the hydrodynamic journal bearing with circumferentially groove are analyzed numerically considering cavitation region, when an external sinusoidal shock is given to the system. The oil film force is obtained by solving the finite width universal Reynolds equation at each time step. Frequency response function and journal orbit obtained from both linear and nonlinear bearing simulations are compared with each other. The vibration response of the journal is different from the expectation obtained from the linear analysis as increase the vibration amplitude of external disturbance. Therefore, the linear theory is not adequate, and the nonlinear calculation such as used in this research is needed to design safety rotor systems.

This paper suggests a method to design the deep groove ball bearing for high-load capacity by using a genetic algorithm. The design problem of ball bearings is a typical discrete/continuous optimization problem because the deep groove ball bearing has discrete variables, such as ball size and number of balls. Thus, a genetic algorithm is employed to find the optimum values from a set of discrete design variables. The ranking process is proposed to effectively deal with the constraints in genetic algorithm. Results obtained fer several 63 series deep groove ball bearings demonstrated the effectiveness of the proposed design methodology by showing that the average basic dynamic capacities of optimally designed bearings increase about 9~34% compared with the standard ones.

This paper describes an investigation on bearing failure due to spragging that has been continuously occurred in turbine hearings. The spragging is defined as the damage found on the leading edge of unloaded pads in the tilting pad journal bearing, In general, the damage mechanism by spragging is classified into fatifgue failure, The principle cause of spragging could be thought as the self-excited vibration by the absence of a stable static equilibrium position of upper pads with no preload. Because of serious consequences of system breakdowns due to bearing failures, determination ar the causes of failure and effective method for countermeasures are very important. This paper describes both the causes of spragging and countermeasures for prevention of such failure, which are taken place in the electric power plants.

Rubbing occurs when a rotating element comes in contact with a stationary element. In the steam turbines, the rotating element is the rotor while the stationary elements are usually the oil deflectors and packing seals. Rubbing phenomenon may be often obseued on a new or rebuilt machine rather than on a machine that has been operating for several months or years. Rubbing in the turbine has been classified into two modes by the operating conditions: 1) start up or shut down, 2) steady state. At start up or shut down operation, rubbing produces synchronous whirl vibration, which are caused by thermal bow of the shaft due to localized heating on the shaft surface. While subsynchronous whirl vibration is caused by partial rubbing during the steady state operation. In this paper, the two case studies of troubleshooting for excessive vibration caused by rubbing in the actual steam turbines are investigated.

This Paper presents the friction and lubrication charateristic related with oil aeration. It is well known that oil aeration occurs severe problem on lubrication system, in particular, in the engine bearings and hydraulic lash adjuster. In this study, engine tests were carried out in motoring conditions. In order to investigate oil aeration characteristics, we measured oil aeration with respect to oil temperature, oil viscosity, modified oil drain system. From the results, we concluded that aeration can be reduced by improving oil drain system and FMEP can be reduced by minimising of aeration.

In the 3-Dimensional contact of the smooth spheres, the effects of friction on the contact area and the distribution of contact pressure was studied numerically. The contact area and pressure distribution was evaluated for the only normal load and for the case of a normal load in the presence of a tangential traction. To do this work, the technique of simple discretization using the load . displacement relationship for a uniformly distributed load of a rectangular patch was used.

A new method for the calculation of a wear amount was suggested. The amount of wear was calculated by the comparison of worn out profile with an estimated original profile. An original profile of wear track was estimated by comparing with outside of wear track. An estimated surface profile was well fitted to the original profile assumed unknown.

In the use of glass fiber reinforced plastics(GFRP), cutting is often necessary. But the most of past studies have been interested in the effect of fiber orientation on tool wear. In this study, the effects of fiber contents on tool wear were investigated experimentally. By proper selection of cutting tool, the variables are cutting speed and fiber contents of 10, 20, 30wt% with fixed feed rate and depth of cut.

Friction and wear characteristics of novolac resin-based friction materials reinforced with aramid pulp and potassium titanate were investigated by using a pad-on-disk type friction tester. Friction properties such as friction stability, surface morphology, and wear rate varied according to the relative amount of aramid pulp and potassium titanate. The friction materials reinforced with both aramid pulp and potassium titanate showed superior friction stability and wear resistance due to the formation of durable transfer layer.

The effects of solid lubricants on wear and friction characteristics of friction materials were studied using a pad-on-disk type friction tester. Friction materials with ten formulations containing different relative amounts of solid lubricants(graphite, MoS$_2$and Sb$_2$S$_3$) were investigated. Results of this work showed that each formulation with different relative amounts of the lubricants had unique friction characteristics. At low brake temperatures, friction materials containing rich graphite showed a small amount of $\mu$ change during sliding. At elevated temperatures, on the other hand, friction materials with rich Sb$_2$S$_3$and graphite showed smaller $\mu$ changes suggesting complementary lubrication of Sb$_2$S$_3$and graphite during sliding. However, the friction materials with rich Sb$_2$S$_3$showed a large amount of wear.

The effect of manufacturing parameters such as molding and curing conditions on friction characteristics of friction materials was studied using a pad-on-disk type friction tester. Friction materials containing 15 ingredients were investigated for an optimal manufacturing condition for the best friction characteristics employing Taguchi robust experimental design. The main effects were different for mechanical properties and friction characteristics and were strongly influenced by manufacturing conditions. An optimum manufacturing condition was obtained to achieve the best friction characteristics concerning mechanical properties(hardness, porosity, wear resistance), friction stability, and change of rotor temperature.

The feasibility of an ultrasonic technique using a pulse-echo method of normal-incident compressional waves was evaluated for its sensitivity to the worn surface and near surface damage due to wear. Worn surfaces were generated at various oscillation frequency under a given load and amplitude and these surface were in situ monitored using a ultrasonic wave detection system. Analysis of the ultrasonic waves received from the worn surface revealed a close relationship between the surface and near-surface damage and the maximum echo-amplitude of the compressional waves. The ultrasonic technique was successful in assessing the level of severity of the worn surface in real time during the wear process. It is also shown that the wear depth can be easily measured by the calculation of change of the specimen thickness based on the wave speed measured for the specimen medium.

The determination of surface topography is believed to be extremely important in the areas of contact mechanics, adhesion and friction. In order to describe topography of various frictional surface, the wear test was carried out under different experimental conditions in dry friction. And fractal descriptors was applied to frictional surface of laser modified steel with image processing system. These descriptors to analyze surface structure are fractal dimension. Surface fractal dimension can be determined by sum of intensity difference of surface pixel. Topography of frictional surface can be effectively obtained by fractal dimensions.

This paper describes the results of analysis, syntheses and Roll Stability of various Di-urea greases. Di-urea greases were synthesized by reaction of 4,4'-Methylenebis(phenyl isocyanate) and various amines, such as cyclohexylamine, octylamine, stearylamine and p-toluidine with base oil at 80-180 $^{\circ}C$. The synthesized di-urea greases were analyzed by FT-R spectroscopy. The Roll Stability of synthesized di-urea greases was evaluated.

The economic loss arisen from the abrasion wear have been increasing at every industrial field. To reduce the economic loss we developed a new process, which is named MAHa process(Metallic Adhesives for HArdening). MAHa process is a process to weld tungsten carbide(WC) to the surface of a plain carbon steel so that it may stay longer under the severe abrasive environment. The depth of the WC layer ranges from 0.5 mm to 5 m. Compared with the conventional technology, arc-augmented welding which bonds WC on the flat surface only, MAHa process has the merits that it can make a robust WC layer on the round or wave- shaped surface also. How to turn the WC powder into a flexible mat is the key technology of the MAHa process. We invented new polymer materials to accomplish such a goal and both the MAHa process and the invented materials were applied for patents. For the application, the inner wall of elbow of Concrete Pump Truck(CPT) was maharized(MAHa process-treated) and the new WC layer on the inner wall was made successfully. The elbow was equipped to a CPT.

Langasite, a new piezoelectric material was polished by CMP(chemical mechanical polishing). To enhance the polishing rate, alumina abrasives were added to commercial ILD1300 slurry which contains silica abrasive. The effect of added alumina 0 the silica slurry on the polishing rate and damage of langasite was investigated, Experimental results show that the polishing rate and roughness increases with increasing added alumina particle size, Crystallinity of the langasite is also lowered by alumina addition.

This paper presents the results of thermoelastic wear phenomena in ventilated disk brakes for a high-speed train using finite element method. The computed results show that the sinusoidal distortions due to non-uniform distributions of temperature profiles may lead to thermoelastic wears at the rubbing surface. This may decrease the life of a disk brake and produce micro-cracks, noise and squeals between two rubbing surfaces.

Using a coupled thermal-mechanical analysis, the dynamic distortion of the ventilated disk brakes has been presented for a high-speed train. The offset ratio between the maximum and minimum values of the thermal distortions has been analyzed as a function of a braking number. The computed FEM results show that the offset ratios in radial direction are much greater than those of circumferentially distorted components. This means that the axial distortions in radial direction may dominantly produce thermally caused wears and cracks at the rubbing surfaces.

The sealing performance of an elastomeric O-ring seat with a temperature gradient has been analyzed for the contact stress behaviors that develop between the O-ring seal and the surfaces with which it comes into contact. The leakage of an O-ring seal will occur when the pressure differential across the seal just exceeds the initial (or static) peak contact stress. The contact stress behaviors that develop in compressed O-rings, in common case of restrained geometry (grooved), are investigated using the finite element method. The analysis includes material hyperelasticity and axisymmetry. The computed FEM results show that the contact stress behaviors are related to a compression rate and a temperature gradient between the vacuum chamber with a groove and the contacting plate with a cooling jacket.

A new conceptual wave rolling ball reducer was proposed and investigated. The main components of the reducer were a eccentric input shaft and bearings, followers with balls, a flange, and a outer ring with waved groove. Followers moved along the holes of the flange according to the rotation of the shaft. And the balls installed in tips of followers were rolled with the waved groove of outer ring. When the shaft was rotated as one revolution and the outer ring was fixed, the flange was rotated as one wave. The kinematic analysis of the reducer carried out. The forces of each components were estimated, and the main design parameters were investigated. The design program using Visual C++ and Auto Lisp to determine the design parameters and to generate the drawing sheet.

The effect of post-irradiation shelf-aging time on the wear of orthopaedic grade UHMWPE was investigated, and wear results were correlated with the time-dependent microstructural changes of polyethylene after gamma irradiation sterilization. The levels of oxidation and crosslinking in the shelf-aged acetabular liners were examined by FTIR and hot xylene extraction, respectively, and uni-directional repeat pass sliding wear tests were conducted by using a pin-on-disc wear tester. Gamma irradiation sterilization in the air environment caused an increase of oxidation, crosslinking, and wear resistance. With aging, however, oxidation progressed and decreased the level of crosslinking. This resulted in a decrease of wear resistance of UHMWPE that was accompanied with the existence of white bands and brittle cracking.

Optimum tribological performance of the head/disk system is critical in maintaining reliable data processing in a hard disk drive. Particularly, as the flying height of the slider continues to decrease with increasing recording density, frictional interaction between the slider and the disk need to be better understood. In this work the effect of reduced ambient pressure on the tribological behavior of the head/disk interface is presented. It is found that surface damage of the components can be accelerated by reducing the ambient pressure. This method may be utilized to assess slider/disk compatibility of newly developed systems in short time.

Acoustic emission(AE) signal has been widely utilized to monitor the interaction at the head/disk interface. In this work the relationship between the AE signal and the state of contact between the slider and the disk is presented. Results of the FFT analyses of the AE signal could be used to better understand the interfacial interaction. Also, it was found that wear particles affect the AE signal. Therefore, the signal can be used to monitor the wear particle presence at the interface.

An analytical study about dynamic behavior of center pivot rocker arm type valve train system equipped with roller of diesel engine is developed. At first, a mathematical model for the dynamic analysis has been set up using the lumped parameter method. In that model, valve spring is divided as some mass elemehts so as to simulate spring surging, Then, how the design parameters, such as valve mass, rocker arm inertia, valve spring stiffness, and initial load on valve spring, affect valve dynamic behavior especially in the valve close area is scrutinized.

The conventional analysis for the numerical computation of fluid film thickness with elastic deformation of contact region. is performed by Newton-Rephson method for its 18st convergence characteristics. However, both high load and relatively low sliding velocity frequently make it impossible for Newton-Rahpson method to get both converged and stable solutions. In particular, this method cannot provide converged Solution under the condition of high load above 1.0 GPa which frequently occurs in line contact of EHL problem. Multigird multi-level method for the solver of non-linear partial differential equation including solid deformation is preferred to Newton-Rshpson method for better convergence and stability and is applied to line contact EHL behavior in this study.