• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1974-1976
• /
• 2005

The feasibility of a midgap metal gate is investigated for 32nm MOSFET low power applications. The midgap metal gate MOSFET is found to deliver a driving current as high as a bandedge gate one for the low power applications if a proper retrograde channel is used. An adequate design of the retrograde channel is essential to achieve the performance requirement given in ITRS roadmap. In addition, a process simulation is run using halo implants and thermal processes to evaluate the feasibility of the necessary retrograde profile in manufacturing environments. From the thermal budget point of view, the bandedge metal gate MOSFET is more vulnerable to the following thermal process than the midgap metal gate MOSFET since it requires a steeper retrograde doping profile. Based on the results, a guideline for the gate workfunction and the channel profile in the 32 nm MOSFET is proposed.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.2
• /
• pp.237-240
• /
• 2006

The feasibility of a midgap metal gate is investigated for a 32 nm MOSFET for low power applications. The midgap metal gate MOSFET is found to deliver $I_{on}$ as high as a bandedge gate if a proper retrograde channel is used. An adequate design of the retrograde channel is essential to achieve the performance requirement given in the ITRS roadmap. A process simulation is also run to evaluate the feasibility of the necessary retrograde profile in manufacturing environments. Based on the simulated result, it is found that any subsequent thermal process should be tightly controlled to retain transistor performance, which is achieved using the retrograde doping profile. Also, the bandedge gate MOSFET is determined be more vulnerable to the subsequent thermal processes than the midgap gate MOSFET. A guideline for gate workfunction $(\Phi_m)$ is suggested for the 32 nm MOSFET.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.4 no.2
• /
• pp.117-123
• /
• 2004

A 30 nm $In_{0.7}GaAs$ High Electron Mobility Transistor (HEMT) with triple-gate has been successfully fabricated using the $SiO_2/SiN_x$ sidewall process and BCB planarization. The sidewall gate process was used to obtain finer lines, and the width of the initial line could be lessened to half by this process. To fill the Schottky metal effectively to a narrow gate line after applying the developed sidewall process, the sputtered tungsten (W) metal was utilized instead of conventional e-beam evaporated metal. To reduce the parasitic capacitance through dielectric layers and the gate metal resistance ($R_g$), the etchedback BCB with a low dielectric constant was used as the supporting layer of a wide gate head, which also offered extremely low Rg of 1.7 Ohm for a total gate width ($W_g$) of 2x100m. The fabricated 30nm $In_{0.7}GaAs$ HEMTs showed $V_{th}$of -0.4V, $G_{m,max}$ of 1.7S/mm, and $f_T$ of 421GHz. These results indicate that InGaAs nano-HEMT with excellent device performance could be successfully fabricated through a reproducible and damage-free sidewall process without the aid of state-of-the-art lithography equipment. We also believe that the developed process will be directly applicable to the fabrication of deep sub-50nm InGaAs HEMTs if the initial line length can be reduced to below 50nm order.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.1 no.1
• /
• pp.31-39
• /
• 2001

W polymetal gate technology for giga bit DRAM are presented. Key module processes for polymetal gate are studied in detail. $W/WN_x/poly-silicon$ adopted for a word line of 256Mbit DRAM has good gate oxide integrity and junction leakage characteristics through full integration, which is comparable to those of conventional $WSi_x$/Poly-silicon gate process. These results undoubtedly show that $W/WN_x/poly-silicon$ is the strongest candidate as a word line for Giga bit DRAM.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.6
• /
• pp.212-216
• /
• 1997

A new metal tip fabrication process for low voltage operation is reported in this paper. The key element of the fabrication process is that isotropic silicon etching and oxidation process used in silicon tip fabrication is utilized for gate hole size reduction and gate oxide layer. A metal FEA with 625 tips was fabricated in order to demonstrate the validity of the new process and submicron gate apertures were successfully obtained from originally 1.7$\mu\textrm{m}$ diameter mask. The emission current above noise level was observed at the gate bias of 50V. The required gate voltage to obtain the anode current of 0.1${\mu}\textrm{A}$/tip was 74V and the emission current was stable above 2${\mu}\textrm{A}$/tip without any disruption. The local field conversion factor and the emitting area were calculated as 7.981${\times}$10\ulcornercm\ulcorner and 3.2${\times}$10\ulcorner$\textrm{cm}^2$/tip, respectively.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.549-552
• /
• 1998

Recently, the gate oxide damage induced by the plasma processes has been one of the most significant reliability issues as the gate oxide thickness falls below 10 nm. The process-induced damage was studied with the metal antenna test structures. In addition to the electron trapping, the hole trapping in a 10 nm thick gate oxide due to the plasma-induced charging was observed in the NMOS's with a metal antenna. The hole trapping gave rise to the decrease of the transconductance (gm) similarly to the case of the electron trapping, but to the extent much less than the electron trapping. It would be because the electrical stress that the plasma-induced charging forced to the gate oxide for the devices with the hole trapping was much smaller than for those with the electron trapping. This hypothesis was strongly supported by the measured characteristics of the Fowler-Nordheim current in the gate oxide.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.729-734
• /
• 2000

Recently, Very Large Scale Integrated (VLSI) circuit & deep-submicron bulk Complementary Metal Oxide Semiconductor(CMOS) devices require gate electrode materials such as metal-silicide, Titanium-silicide for gate oxides. Many previous authors have researched the improvement sub-micron gate oxide quality. However, few have reported on the electrical quality and reliability on the ultra thin gate oxide. In this paper, at first, I recommand a novel shallow trench isolation structure to suppress the corner metal-oxide semiconductor field-effect transistor(MOSFET) inherent to shallow trench isolation for sub 0.1${\mu}{\textrm}{m}$ gate oxide. Different from using normal LOCOS technology deep-submicron CMOS devices using novel Shallow Trench Isolation(STI) technology have a unique"inverse narrow-channel effects"-when the channel width of the devices is scaled down, their threshold voltage is shrunk instead of increased as for the contribution of the channel edge current to the total channel current as the channel width is reduced. Secondly, Titanium silicide process clarified that fluorine contamination caused by the gate sidewall etching inhibits the silicidation reaction and accelerates agglomeration. To overcome these problems, a novel Two-step Deposited silicide(TDS) process has been developed. The key point of this process is the deposition and subsequent removal of titanium before silicidation. Based on the research, It is found that novel STI structure by the SEM, in addition to thermally stable silicide process was achieved. We also obtained the decrease threshold voltage value of the channel edge. resulting in the better improvement of the narrow channel effect. low sheet resistance and stress, and high threshold voltage. Besides, sheet resistance and stress value, rms(root mean square) by AFM were observed. On the electrical characteristics, low leakage current and trap density at the Si/SiO$_2$were confirmed by the high threshold voltage sub 0.1${\mu}{\textrm}{m}$ gate oxide.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.3
• /
• pp.14-17
• /
• 2002

The HDP (High Density Plasma) CVD process consists of a simultaneous sputter etch and chemical vapor deposition. As CMOS process continues to scale down to sub- quarter micron technology, HDP process has been widely used fur the gap-fill of small geometry metal spacing in inter-metal dielectric process. However, HBP CVD system has some potential problems including plasma-induced damage. Plasma-induced gate oxide damage has been an increasingly important issue for integrated circuit process technology. In this paper, thin gate oxide charge damage caused by HDP deposition of inter-metal dielectric was studied. Multiple step HDP deposition process was demonstrated in this work to prevent plasma-induced damage by introducing an in-situ top SiH$_4$ unbiased liner deposition before conventional deposition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.181-184
• /
• 2001

Chemical Mechanical Polishing(CMP) of Shallow Trench Isolation(STD structure in 0.18 m semiconductor device fabrication is studied. CMP process is applied for the STI structure with and without reverse moat pattern and End Point Detection (EPD) method is tested. To optimize the transistor properties related metal 1 parameters. we studied the correlation between CMP thickness of STI using high selectivity slurry. DOE of gate etch recipe, and 1st metal DC values. Remaining thickness of STI CMP is proportional to the thickness of gate-etch process and this can affect to gate profile. As CMP thickness increased. the N-poly foot is deteriorated. and the P-Poly Noth is getting better. If CD (Critical Dimension) value is fixed at some point,, all IDSN/P values are in inverse proportional to CMP thickness by reason of so called Profile Effect. Weve found out this phenomenon in all around DOE conditions of Gate etch process and we also could understand that it would not have any correlation effects between VT and CMP thickness in the range of POE 120 sec conditions. As CMP thickness increased by $100\AA$. 3.2 $u\AA$ of IDSN is getting better in base 1 condition. In POE 50% condition. 1.7 $u\AA$ is improved. and 0.7 $u\AA$ is improved in step 2 condition. Wed like to set the control target of CD (critical dimension) in gate etch process which can affect Idsat, VT property versus STI topology decided by CMP thickness. We also would like to decide optimized thickness target of STI CMP throughout property comparison between conventional STI CMP with reverse moat process and newly introduced STI CMP using high selectivity slurry. And we studied the process conditions to reduce Gate Profile Skew of which source known as STI topology by evaluation of gate etch recipe versus STI CMP thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.181-184
• /
• 2001

Chemical Mechanical Polishing(CMP) of Shallow Trench Isolation(STI) structure in 0.18 m semiconductor device fabrication is studied. CMP process is applied for the STI structure with and without reverse moat pattern and End Point Detection (EPD) method is tested. To optimize the transistor properties related metal 1 parameters, we studied the correlation between CMP thickness of STI using high selectivity slurry, DOE of gate etch recipe, and 1st metal DC values. Remaining thickness of STI CMP is proportional to the thickness of gate-etch process and this can affect to gate profile. As CMP thickness increased, the N-poly foot is deteriorated, and the P-Poly Noth is getting better. If CD (Critical Dimension) value is fixed at some point, all IDSN/P values are in inverse proportional to CMP thickness by reason of so called Profile Effect. Weve found out this phenomenon in all around DOE conditions of Gate etch process and we also could understand that it would not have any correlation effects between VT and CMP thickness in the range of POE 120 sec conditions. As CMP thickness increased by 100 ${\AA}$, 3.2 u${\AA}$ of IDSN is getting better in base 1 condition. In POE 50% condition, 1.7 u${\AA}$ is improved, and 0.7 u${\AA}$ is improved in step 2 condition. Wed like to set the control target of CD (critical dimension) in gate etch process which can affect Idsat, VT property versus STI topology decided by CMP thickness. We also would like to decide optimized thickness target of STI CMP throughout property comparison between conventional STI CMP with reverse moat process and newly introduced STI CMP using high selectivity slurry. And we studied the process conditions to reduce Gate Profile Skew of which source known as STI topology by evaluation of gate etch recipe versus STI CMP thickness.