• Journal of the Korean Electrochemical Society
• /
• v.16 no.2
• /
• pp.85-90
• /
• 2013

Graphite is a commercial anode material to have the specific capacity of 372 mAh/g and the true density of 2.2 g/ml. Many effort had been pouring to find out the better material than graphite. Good candidates are silicon, tin, etc. Zinc is also a plausible candidate to have the specific capacity of 412 mAh/g and the true density of 7.14 g/ml. In this study, the Zn based anode material including indium and nickel as minor additives was synthesised. In order to get the homogeneouly mixed Zn-In-Ni composite material, the sol-gel method was used. The anode prepared by Zn-In-Ni composite material has the $1^{st}$ specific capacity of 910 mAh/g. Through prolonged charge-discharge cycling, the specific capacities were reduced to 365 (at $31^{st}$ cycle) and 378 mAh/g (at $62^{th}$ cycle). The $1^{st}$ Ah efficiency was 45% and Ah efficiencies were exhibited at the prolonged cycle.

• Journal of Sensor Science and Technology
• /
• v.3 no.1
• /
• pp.68-77
• /
• 1994

Grid type 70Ni-30Co thin films on slide glass at $250^{\circ}C$ has been fabricated to develope. From fabricated sensors using above process, we investigated the relation of temperature, resistivity, line width to magnetoresistance and we obtained the following results after observation of coercive force, saturated magnetization, maxium usable sensitivity, delay time, slew rate, white noise, resolution of the sensors. We confirmed that the $600{\AA}$ thin film at $250^{\circ}C$ formed crystalized magnetic anisotropy spontaneously and the sensor using the thin film had capability of detecting magnetic field with sensitivity of 230 nT. In these devices, the magnetoresistance change was increased linearly in ${\pm}10$ Oe range, and the magnetoresistance effect was increased when the ratio between line width and length was increased. When the devices was soldered using indium, the temperature-resistivity coefficient showed $8{\times}10^{-3}/deg$ and increased during the specific properties as magnetic field sensor were weakened. In this studies, the coercive forces of the films were about 5.1 A/cm and saturated magnetizations were 0.64 T, and the delay time in these devises was $5{\mu}s$ and slew rate showed 0.39 $Oe/{\mu}s$ and white noise was -120 dB.

• Journal of the Korean Vacuum Society
• /
• v.15 no.1
• /
• pp.64-72
• /
• 2006

We demonstrated organic light-emitting devices (OLEDs) based on the organic thin-film materials such as tris-(8-hydroxyquinoline) aluminum $(Alq_3)$. The structure of OLEDs was vacuum deposited upon transparent and thin glass substrates pre-coated with a transparent, conducting indium tin oxide thin film. The luminance characteristics, current, capacitance, and dispersion factor for degraded OLEDs, which were made by various bias currents $(0.5mA\;{\leq}\;I_{Bias}\;{\leq}9mA)$, are studied. The current dependences of lifetime were divided at approximately 2mA, and they represented nearly linear behaviors but had different slopes in a logarithmic plot of lifetime versus bias current. With lighting OLEDs, the anomaly of capacitance, as shown in the CV curve, occurred because of two factors, polarization in the bulk of organic materials and the interface between the metal and organic layers. In decayed OLEDs that had lower bias currents of less than 2mA, it was found that the degradation of luminance was related to both the decrease of polarization and to the lowering of the injection barrier.

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.321-326
• /
• 2013

The effect of rapid thermal annealing (RTA) on the optical properties of digital-alloy InGaAlAs multiple quantum well (MQW) structures have been investigated by using photoluminescence (PL) and time-resolved PL measurements as a function of RTA temperature. The MQW samples were annealed from $700^{\circ}C$ to $850^{\circ}C$ for 30 s in a nitrogen atmosphere. The MQW sample annealed at $750^{\circ}C$ exhibited the strongest PL intensity and the narrowest FWHM (Full width at half maximum), indicating the reduced nonradiative recombination centers and the improved interfaces between the wells and barriers. The MQW samples annealed at $800^{\circ}C$ and $850^{\circ}C$ showed the decreased PL intensities and blueshifted PL peaks compared to $750^{\circ}C$-annealed sample. The blueshift of PL peak with increasing RTA temperatures are ascribed to the increase of aluminum due to intermixing of gallium (Ga) and aluminum (Al) in the interfaces of InGaAs/InAlAs short-period superlattices. The decrease of PL intensity after annealing at $800^{\circ}C$ and $850^{\circ}C$ are attributed to the interface roughening and lateral composition modulation caused by the interdiffusion of Ga and Al and indium segregation, respectively. With increasing RTA temperature the PL decay becomes slower, indicating the decrease of nonradiative defect centers. The optical properties of digital-alloy InGaAlAs MQW structures can be improved significantly with optimum RTA conditions.

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.306-312
• /
• 2013

Single-crystalline InSb nanowire was synthesized on $SiO_2$ wafer via vapor-liquid-solid (VLS) mechanism using chemical vapor deposition method. According to the source container system (open or close) which contain InSb powder and $SiO_2$ wafer, the single-crystalline InSb nanowires have different growth mechanisms. Structural characterization of the InSb nanowires was examined by scanning electron microscope (SEM). Composition of the nanowires was investigated using x-ray diffraction (XRD) and energy dispersive x-ray spectroscopy (EDS). This study demonstrates that length and diameter of the InSb nanowires are long and thick using open-boat system by VLS and additional vapor-solid (VS) mechanisms, because open-boat system can carry a large amount of vapor-phase InSb precursor than close-boat system.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.22-29
• /
• 2011

An infrared thermographic imaging module of [$320{\times}256$] focal-plane array (FPA) based on [InAs/GaSb] strained-layer superlattice (SLS) was fabricated, and its images were demonstrated. The p-i-n device consisted of an active layer (i) of 300-period [13/7]-ML [InAs/GaSb]-SLS and a pair of p/n-electrodes of (60/115)-period [InAs:(Be/Si)/GaSb]-SLS. FTIR photoresponse spectra taken from a test device revealed that the peak wavelength (${\lambda}_p$) and the cutoff wavelength (${\lambda}_{co}$) were approximately $3.1/2.7{\mu}m$ and $3.8{\mu}m$, respectively, and it was confirmed that the device was operated up to a temperature of 180 K. The $30/24-{\mu}m$ design rule was applied to single pixel pitch/mesa, and a standard photolithography was introduced for [$320{\times}256$]-FPA fabrication. An FPA-ROIC thermographic module was accomplished by using a $18/10-{\mu}m$ In-bump/UBM process and a flip-chip bonding technique, and the thermographic image was demonstrated by utilizing a mid-infrared camera and an image processor.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.356-360
• /
• 2011

Indium oxide ($In_2O_3$) single layer and $In_2O_3$/copper (Cu) bi-layer films were prepared on glass substrates by RF and DC magnetron sputtering without intentional substrate heating. In order to determine the effect of the Cu bottom layer on the optical, electrical and structural properties of $In_2O_3$ films, 3-nm-thick Cu film was deposited on the glass substrate prior to deposition of the $In_2O_3$ films. As-deposited $In_2O_3$ films had an optical transmittance of 79% in the visible wavelength region and a sheet resistance of 2,300 ${\Omega}/{\square}$, while the $In_2O_3$/Cu film had optical and electrical properties that were influenced by the Cu bottom layer. $In_2O_3$/Cu films had a lower sheet resistance of 110 ${\Omega}/{\square}$ and an optical transmittance of 71%. Based on the figure of merit, it can be concluded that the Cu bottom layer effectively increases the performance of $In_2O_3$ films for use as transparent conducting oxides in flexible display applications.

• Journal of the Korean Vacuum Society
• /
• v.20 no.4
• /
• pp.288-293
• /
• 2011

We investigated the effects of piezoelectric field on the electro-absorption characteristics in InGaN/GaN multiple-quantum well (MQW) green light emitting diodes (LED). Double crystal X-ray diffraction measurement was performed to study the crystalline property and indium (In) composition in the MQW active layer. To measure the electro-luminescence and electro-reflectance (ER) spectroscopy, we fabricated the $1{\times}1\;mm^2$ large-area green LED chip. The piezoelectric field inside the LED structure was evaluated from the Vcomp in active layer by the ER spectra. Finally, we analyzed the electro-absorption characteristics of the green LED by using the photo-current spectroscopy.

• Journal of the Korean Vacuum Society
• /
• v.21 no.5
• /
• pp.264-272
• /
• 2012

In this paper, we report THz generation and detection characteristics investigated by InGaAs semiconductor epilayers, as results of a basic study obtained from the InGaAs-based THz transmitter/receiver (Tx/Rx). High-temperature and low-temperature (LT) grown InGaAs epilayers were prepared by the molecular beam epitaxy technique for the characterization of THz generation and detection, respectively, and the surface emission based on the photo-Dember effect was tried for THz generation. THz wave was generated by irradiation of a Ti:Sapphire fs pulse laser (60 ps/83 MHz), and a LT-GaAs Rx was used for the THz detection. The frequency band shown in the spectral amplitudes Fourier-transformed from the measured current signals was ranging in 0.5~2 THz, and the signal currents were exponentially increased with the Tx beam power. The THz detection characteristics of LT-InGaAs were investigated by using an Rx with dipole (5/20 ${\mu}m$) antenna, and the cutoff frequency was ~2 THz.

• The Journal of Korean Academy of Prosthodontics
• /
• v.30 no.2
• /
• pp.135-154
• /
• 1992

This study was performed to analyze bond strength, the alterations of the interfaces between metal films which are populary used and considered to contribute to the chemical reaction with porcelain, according to constant ion- beam- mixing, and the relation between interfacial chemical reactions and bond strength in metal/porcelain specimens. For this study, three seperate metals : selected-gold, indium and tin were chosen ; each to be bonded to a seperate body porcelain. Bonding occurs when the metal is deposited to the body porcelain using a vacuum evaporator. The vacuum evaporator used $10^{-5}\sim10^{-6}$ Torr vacuum states for the evaporation of various metals (Au, Sn, In). Ion-beam-mixing of the porcelain/metal interfaces caused reactions when the Ar+ was implanted into thin films using a 80 KeV accelerator. These ion-beam-mixed specimens were then compared with an unmixed control group. An analysis of bond strength and ionic changes between the the metal and porcelain was performed by electron spectroscopy of chemical analysis (ESCA) and scratch test. The finding led to the following conclusions : 1. Light microscopic views of the scratch test : The ion-beam-mixed Au/porcelain specimen showed narrower scratched streams than the unmixed specimen. However, the Sn/porcelain, In/porcelain specimens showed no differences in the two conditions. 2. Acoustic emissions in scratch tests : The ion-mixed Au/porcelain, In/porcelain specimens showed signals closer to the metal/porcelain interfaces than unmixed specimens. Conversely, the ion-mixed Sn/porcelain specimen showed more critical signals in superficial portions than unmixed specimens. 3. After ion- beam-mixing, the Au/porcelain specimen showed apparently increased bond strength, and the In/porcelain specimen showed very slightly increased bond strength. However, the Sn/porcelain specimen showed no differences between ion mixed specimen and the unmixed one. 4. ESCA analysis : The ion-beam-mixed Au/porcelain specimen showed a higher peak separated value (4.3eV) than that of the unmixed specimen(3.65eV), the ion-beam-mixed In/porcelain specimen showed a higher peak separated value (9.43eV) than that of the unmixed specimen(7.6eV) and the ion-beam-mixed Sn/porcelain specimen showed a higher peak separated value (8.79eV) than that of the unmixed specimen(8.5eV). 5. Interfacial changes were observed in the ion-mixed Au/porcelain, In/porcelain and Sn/porcelain specimens. Especially, significant interfacial changes were measured in the ion- mixed Sn/porcelain specimen. Tin dioxide(SnO2) and a combination of pure tin and tin dioxide (Sn+SnO2) were produced. 6. In the Au/porcelain specimen, the interfacial chemical reaction showed increased bond strength between gold and porcelain substrate. But, in the In/porcelain, Sn/porcelain specimens, interfacial chemical reactions did not affected the bond strength between metal and porcelain substrate. Especially, bonding strength on the ion mixed Sn/porcelain specimen showed the least amount of difference.