• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.8
• /
• pp.847-852
• /
• 2014

As the scaling trend becomes accelerated in process technology for cost reduction in semiconductor chip manufacturing, the requirement for shrink technology has increased. Hot Carrier Injection (HCI) degradation for I/O transistors is most concerning part when shrink. To solve this, the effective channel length (Leff) was increased using liner oxide before Light Doped Drain (LDD) implants and optimized the tilt angle to increase Leff without E-field degradation in LDD region, satisfying the HCI specification.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.2
• /
• pp.36-45
• /
• 1993

The n-channel MOSFETs with gate-$n^{-}$S/D overlapped structure have been fabricated by ITLDD(inverse-T gate lightly doped drain) technology. The gate length(L$_{mask}$) was 0.8$\mu$m. The degradation effects of hot carriers injected into the gate oxide were analyzed in terms of threshold voltage, transconductance and drain current variations. The degradation dependences on the gate voltage and drain voltage were characterized. The devices with higher n-concentration showed higher resistivity against the hot carrier injection. As the results of investigating the lifetime of the device, the lifetime showed longer than 10 years at V$_{d}$ = 5V for the overlapped devices with the implantation of an phosphorus dose of 5$\times$10$^{13}$ cm$^{-2}$ and an energy of 80 keV in the n$^{-}$resion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.266-269
• /
• 1997

Hot carrier effects as a function of bias stress time and bias stress conditions were syste-matica1ly investigated in p-channel po1y-Si TFT's fabricated on the quartz substrate. The device degradation was observed for the negative bias stress. After positive bias stressing, Improvement of electrical characteristic except for subthreshold slope was observed. It was found that these results were related to the hot carrier injection into the gate oxide and interface states at the poly-Si/SiO$_2$interface rather than defects states generation under bias stress.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1367-1369
• /
• 1998

To achieve the ULSI goals of higher density, greater performance and operation speed have been scaled down. However, the reduction of channel length cause undesirable problems such as drop of punchthrough voltage, hot-carrier degradation and high leakage current, etc.. It is shown that the device characteristics depend on process parameters. In this Paper, we catched hold of trends of hot-carrier effects and punchthrough voltages due to variation of some process parameters such as LDD doses(P), spacer lengths, channel doses($BF_2$) and $V_T$ adjusting channel implantation energies using design trend curve (DTC). As the LDD and channel doses increased, hot-carrier phenomena became more severe, and punchthrough voltage was decreased. It were represented that punchthrough and hot carrier effects were critically depend on LDD and channel doses.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.3
• /
• pp.169-172
• /
• 2020

In this paper, the effect of hot carrier injection on an n-bulk fin field-effect transistor (FinFET) is analyzed. The hot carrier injection method is applied to determine the performance change after injection in two ways, channel hot electron (CHE) and drain avalanche hot carrier (DAHC), which have the greatest effect at room temperature. The optimum condition for CHE injection is V_G=V_D, and the optimal condition for DAHC injection can be indirectly confirmed by measuring the peak value of the substrate current. Deterioration by DAHC injection affects not only hot electrons formed by impact ionization, but also hot holes, which has a greater impact on reliability than CHE. Further, we test the amount of drain voltage that can be withstood, and extracted the lifetime of the device. Under CHE injection conditions, the drain voltage was able to maintain a lifetime of more than 10 years at a maximum of 1.25 V, while DAHC was able to achieve a lifetime exceeding 10 years at a 1.05-V drain voltage, which is 0.2 V lower than that of CHE injection conditions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.12
• /
• pp.792-796
• /
• 2014

In this paper, we investigated the hot carrier reliability of two kinds of device with low threshold voltage (LVT) and regular threshold voltage (RVT) in 65 nm CMOS technology. Contrary to the previous report that devices beyond $0.18{\mu}m$ CMOS technology is dominated by channel hot carrier(CHC) stress rather than drain avalanche hot carrier(DAHC) stress, both of LVT and RVT devices showed that their degradation is dominated by DAHC stress. It is also shown that in case of LVT devices, contribution of interface trap generation to the device degradation is greater under DAHC stress than CHC stress, while there is little difference for RVT devices.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.970-973
• /
• 1999

When the size of the device is decreased, the hot carrier degradation presents a severe problem for long-term device reliability. In this paper we fabricated & tested the 0.26${\mu}{\textrm}{m}$ NMOSFET with wet gate oxide and nitride oxide gate to compare that the characteristics of hot carrier effect, charge to breakdown, transistor Id_Vg curve and charge trapping using the Hp4145 device tester As a result we find that the characteristics of nitride oxide gate device better than wet gate oxide device, especially a hot carrier lifetime(nitride oxide gate device satisfied 30years, but the lifetime of wet gate oxide was only 0.1year), variation of Vg, charge to breakdown and charge trapping etc.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.10
• /
• pp.130-138
• /
• 1996

The size of a device needs to scale down to increase its integrity and speed. As the size of the device is reduced, the hot-carrier degradation that severely effects on device reliabilty is concerned. In this paper, sub-micron buried-channel P-MOSFETs were fabircated, and the hot-carrier effects were invetigated. Also the hot-carrier effect in the buired-channel P-MOSFETs and the surface-channel P-MOSFETs were compared with simulation programs using SUPREM-4 and MINIMOS-4. This paper showed that the electric characteristics of sub-micron P-MOSFET are different from those of N-MOSFET. Also it showed that the punchthrough voltage ( $V_{pt}$ ) was abruptly drop after applying the stress and became almost 0V when the channel lengths were shorter than 0.6.mu.m. The lower punchthrough voltage causes the device to operte poorly by the deterioration of cut-off characteries in the switching mode. We can conclude that the buried channel P-MOSFET for CMOS circuits has a limit of the channel length to be around 0.6.mu.m.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.9
• /
• pp.736-742
• /
• 1991

N$^{+}$poly gate NMOSFETs and p$^{+}$ poly gate (surface type) PMOSFETs with three different gate oxides(SiO2, NO, and ONO) were fabricated. The rapid thermal nitridation and reoxidation techniques have been applied to gate oxide formation. The current drivability of the ONO NMOSFET shows larger values than that of the SiO2 NMOSFET. The snap-back occurs at a lower drain voltage for SiO$_2$ cases for ONO NMOSFET. Under the maximum substrate current bias conditions, hot-carrier effects inducting threshold voltage shift and transconductance degradation were investigated. The results indicate that ONO films exhibit less degradation in terms of threshold voltage shift. It was confirmed that the ONO samples achieve good improvement of hot-carrier immunity. In a SiO$_2$ SC-PMOSFET, with significant boron penetration, it becomes a depletion type (normally-on). But ONO films show excellent impurity barrier properties to boron penetration from the gate.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.6
• /
• pp.59-66
• /
• 1995

The hot electron induced effective channel length modulation (${\Delta}L_{H}$) and HEIP characteristics in PMOSFET's after bidirectional stress are presented. Trapped electron charges in gate oxide and lateral field are calculated from the gate current model, and ${\Delta}L_{H}$(${\Delta}L_{HD},\;{\Delta}L_{HS}$) is calculated using trapped electron charges and lateral field. It has been found that ${\Delta}I_{d}$and ${\Delta}L_{H}$ are more affected by the stress order (Forward-Reverse of Reverse or Reverse-Forward) than the stress direction, and they vary logarithmically with the stress time. In contrast, ${\Delta}V_{t}$ and ${\Delta}V_{pt}$ are more affected by the stress direction thatn the stress order. The correlation between ${\Delta}V_{pt}$ and the stress time can be explanined as the following polynomial functin: ${\Delta}V_{pt}$=AT$^{n}$. It has also been shown that PMOSFET degradation is related with the gate current and the effects of ${\Delta}V_{pt}$ is the most significant.