• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.39 no.4
• /
• pp.43-53
• /
• 2002

In this paper, a new dynamic D-flip-flop which does not suffer from charge sharing and glitch problems is proposed. And a dual-modulus divide-by-128/129 prescaler has been designed with the proposed D-flip-flops using a 0.6$0.6{\mu}m$ CMOS technology. Eleven-transistor architecture enables it to operate at the higher frequency range and the transistor merging technique contributes to the reduction of power consumption. At 5V supply voltage, the simulated maximum operating frequency and the current consumption of the divide-by-128/129 prescaler are 1.97GHz and 7.453mA, respectively.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.4
• /
• pp.211-216
• /
• 2003

This work describes a 3 V 12b 100 MS/s CMOS digital-to-analog converter (DAC) for high-speed communication system applications. The proposed DAC is composed of a unit current-cell matrix for 8 MSBs and a binary-weighted array for 4 LSBs, trading-off linearity, power consumption, chip area, and glitch energy with this process. The low-glitch switch driving circuits are employed to improve linearity and dynamic performance. Current sources of the DAC are laid out separately from the current-cell switch matrix core block to reduce transient noise coupling. The prototype DAC is implemented in a 0.35 um n-well single-poly quad-metal CMOS technology and the measured DNL and INL are within ${\pm}0.75$ LSB and ${\pm}1.73$ LSB at 12b, respectively. The spurious-free dynamic range (SFDR) is 64 dB at 100 MS/s with a 10 MHz input sinewave. The DAC dissipates 91 mW at 3 V and occupies the active die area of $2.2{\;}mm{\;}{\times}{\;}2.0{\;}mm$

• 전자공학회논문지 IE
• /
• v.43 no.3
• /
• pp.6-12
• /
• 2006

This paper described an 8bit, 100Msample/s CMOS D/A converter using a glitch-time minimization technique for the high-speed sampling rate of 100MHz level. The proposed DAC was implemented in $0.35{\mu}m$ Hynix CMOS technology and adopts a current mode architecture to optimize sampling rate, resolution, chip area. The DAC linear characteristics was similar to the proposed specification and the prototype error between DNL and INL is less than $\pm$0.09LSB respectively. Also, the manufactured DAC chip was analyzed the cause of error operation and proposed the field considerations for chip test.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.532-535
• /
• 2003

Vibration of rotating machinery is a factor that is something to do with abnormal machinery. Former days, Perception of vibration at rotating machinery had used Shaft rider type. Shaft rider type was adhered to surface of shaft and detected vibration of rotating machinery. Recently, Perception of vibration at rotating machinery uses to non-contact sensor. Working principle of non-contact sensor is used of eddy current. Vibration at rotating machinery appears to deviation of eddy current. In this paper, We investigate abnormal vibration due to non-contact sensor.

• Proceedings of the Korean Information Science Society Conference
• /
• 2001.10a
• /
• pp.577-579
• /
• 2001

휴대용 전자 제품의 수요가 증가함에 따라 전자 제품의 전력 소모를 감소시키는 문제가 중요하게 되었다. 예를 들면 현재 사용자가 급속도로 늘고 있는 개인 휴대 전화기나 노트북 컴퓨터는 소형화와 배터리의 사용시간 연장 등이 가장 중요한 기술적인 요소로 작용하고 있다. 전력소모를 줄이기 위해서 게이트 크기를 재결정하는 방법과 버퍼를 삽입함으로써 글리치를 줄이는 방법이 사용되고 있는데 최근에 버퍼의 위치를 결정하는 데 정수 선형계획법이 제안되었다. 본 연구에서는 최대 가중 독립 집합을 찾는 알고리즘을 이용해 버퍼의 위치를 결정 방법을 제안하였고 실험을 통해 효율성을 입증하였다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.12
• /
• pp.1983-1993
• /
• 1993

A power-reduction technique for full-flash A/D converters is proposed. As the resolution of a full-flash A/D converter increases linearly, the number of comparators increases exponentially. The power dissipation is generally larger than other A/D converter architectures because there are many comparators, and they are operating continuously. In this proposed architecture, only a selected number of conmarators are made to operate instead of activating all the comparators of the full-flash A/D convertor. To determine whichcomparators should be activated, voltage levelfider circuits are used. A new clock driver is developed to suppress the dynamic glitch noise which is fed back into the input stage of the comparator. By using this clock driver, the glitch noise in the current source is reduced to one fourth of that when the typical clock signal is applied. The proposed architecture has been implemented with 1.2 m 5GHz BiCMOS technology. The maximum conversion speed is 350Msamples/s. and dissipates only 900mW.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.13-18
• /
• 2013

In this paper design a 8 bit Current Steering D/A Converter for stimulating neuron signal. Proposed circuit in paper shows the conversion rate of 10KS/s and the power supply of 3.3V with 0.35um Magna chip CMOS process using full custom layout design. It employes segmented structure which consists of 3bit thermometer decoders and 5bit binary decoder for decreasing glitch noise and increasing resolution. So glitch energy is down by $10nV{\bullet}sec$ rather than binary weighted type DAC. And it makes use of low power current stimulator because of low LSB current. And it can make biphasic signal by connecting with Micro Controller Unit which controls period and amplitude of signal. As result of measurement INL is +0.56/-0.38 LSB and DNL is +0.3/-0.4 LSB. It shows great linearity. Power dissipation is 6mW.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.9
• /
• pp.685-691
• /
• 2003

This work describes a 3 V 12b 100 MS/s CMOS digital-to-analog converter (DAC) for high-speed communication system applications. The proposed DAC is composed of a unit current-cell matrix for 8 MSBs and a binary-weighted array for 4 LSBs, considering linearity, power consumption, chip area, and glitch energy. The low-glitch switch driving circuit is employed to improve the linearity and the dynamic performance. Current sources of the DAC are laid out separately from the current-cell switch matrix core. The prototype DAC is implemented in a 0.35 urn n-well single-poly quad-metal CMOS technology. The measured DNL and INL of the prototype DAC are within $\pm$0.75 LSB and $\pm$1.73 LSB, respectively, and the spurious-free dynamic range (SFDR) is 64 dB at 100 MS/s with a 10 MHz input sinewave. The DAC dissipates 91 mW at 3 V and occupies the active die area of 2.2 mm ${\times}$ 2.0 mm.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.11
• /
• pp.61-66
• /
• 2005

This paper describes a 10-bit 210MHz CMOS current-mode Digital-to-Analog Converter (DAC) consisting of 6 bit MSB current cell matrix Sub-DAC, 2 bit mSB unary current source Sub-DAC, and 2 bit LSB binary weighting Sub-DAC for Wireless LAN application. A new deglitch circuit is proposed to control a crossing point of signals and minimize a glitch energy. The proposed 10-bit CMOS current mode DAC was designed by a $0.35{\mu}m$ CMOS double-poly four-metal technology rate of 210MHz, DNL/INL of ${\pm}0.7LSB/{\pm}1.1LSB$, a glitch energy of $76pV{\cdot}sec$, a SNR of 50dB, a SFDR of 53dB at 200MHz sampling clock and power dissipation of 83mW at 3.3V

• Journal of IKEEE
• /
• v.21 no.4
• /
• pp.331-337
• /
• 2017

In this paper, we present the design of a 20MHz bandwidth 3rd-order continuous-time low-pass sigma-delta modulator with low-noise and low-power consumption. The bandwidth of the system is sufficient to accommodate LTE and other wireless network standards. The 3rd-order low-pass filter with feed-forward architecture achieves the low-power consumption as well as the low complexity. The system uses 3bit flash quantizer to provide fast data conversion. The current-steering DAC achieves low-power and improved sensitivity without additional circuitries. Cross-coupled transistors are adopted to reduce the current glitches. The proposed system achieves a peak SNDR of 65.9dB with 20MHz bandwidth and power consumption of 32.65mW. The in-band IM3 is simulated to be 69dBc with 600mVp-p two tone input tones. The circuit is designed in a 0.18-um CMOS technology and is driven by 500MHz sampling rate signal.