• JSTS:Journal of Semiconductor Technology and Science
• /
• v.3 no.4
• /
• pp.188-193
• /
• 2003

This paper describes a novel burst-mode clock and data recovery (CDR) circuit which can be used for 622Mbps burst mode applications. The CDR circuit is basically a phase locked loop (PLL) having two phase detectors (PDs), one for the reference clock and the other for the NRZ data, whose operations are controlled by an external control signal. This CDR was fabricated in a 1-poly 5-metal $0.25{\;}\mu\textrm{m}$ CMOS technology. Jitter generation, burst/continuous mode data receptions were tested. Operational frequency range is 320Mhz~720Mhz and BER is less than 1e-12 for PRBS31 at 622Mhz. For the same data sequence, the extracted clock jitter is less than 8ps rms. Power consumption of 100mW was measured without I/O circuits.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.459-460
• /
• 2008

In this paper, a 10Gbps clock and data recovery circuit is designed in $0.18{\mu}m$ CMOS technology. The circuit incorporates a multiphase LC oscillator, a quarter-rate Bang-Bang phase detector, a charge pump and a second order loop filter. The simulation results show that the designed circuit has a peak-to-peak clock jitter of 4.2ps and a peak-to-peak recovered data jitter of 8ps while consuming about 80mW from a 1.8V supply.

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.197-198
• /
• 2007

In this paper, a 10Gbps Clock and Data Recovery circuit is designed in $0.18{\mu}m$ CMOS Technology. The circuit incorporates a multiphase LC oscillator, a quarter-rate Bang-Bang phase detector, a Charge Pump and a second order loop filter. The simulation results show that the designed circuit has a peak-to-peak clock jitter of 4.1ps and a peak-to-peak recovered data jitter of 8ps while consuming about 44mW from a 1.8V supply.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12C
• /
• pp.249-254
• /
• 2001

A receiver ASIC for fiber optic modules of STM-1 optical communication has been fabricated with 0.65 $\mu\textrm{m}$ CMOS technology. The ASIC has a limit amplifier circuit for the 155.52 Mbps data reshaping, and a clock extraction circuit for the 155.52 MHz clock recovery. The ASIC has an acquisition aid and LOS monitoring circuit for properly operation with near 155.52 MHz clock frequency in case of the data loss due to transmission line open or data transfer fail. Measured results show that the circuit reshapes data from 5 mV to 1 V wide range of input voltage condition, add it recovers system clock with stable on any condition.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.10C
• /
• pp.987-992
• /
• 2002

In this paper, a new clock and data recovery circuit is proposed for the application of data communication systems requiring ㎓-range clock signals. The circuit is suitable for recovering NRZ data which is widely used for high speed data transmission in ㎓ ranges. The high frequency jitter is one of major performance-limiting factors in PLL, particularly when NRZ data patterns are used. A novel phase detector is able to suppress this noise, and stable clock generation is achieved. Futhermore, the phase detector has an adaptive delay cell removing the dead zone problem and has the optimal characteristics for fast locking. The proposed circuit has a convenience structure that can be easily extended to multi-channels. The circuit is designed based on CMOS 0.25㎛ fabrication process and verified by measurement result.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.3
• /
• pp.185-192
• /
• 2013

In this paper, a clock and data recovery (CDR) circuit that supports triple data rates of 1.62, 2.7, and 5.4 Gbps for DisplayPort 1.2 standard is described. The proposed CDR circuit covers three different operating frequencies with a single VCO switching the operating frequency by the 3-bit digital code. The prototype chip has been designed and verified using a 65 nm CMOS technology. The recovered-clock jitter with the data rates of 1.62/2.7/5.4 Gbps at $2^{31}$-1 PRBS is measured to 7/5.6/4.7 $ps_{rms}$, respectively, while consuming 11 mW from a 1.2 V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.11
• /
• pp.44-49
• /
• 2008

We have proposed a clock recovery circuit for 13.56MHz RFID Tags using 100%, ASK RF input signal. The proposed clock recovery circuit generates clock pulses without reference clock by adapting register controlled DLL. The proposed circuit have designed by using a TSMC 0.18um 1P6M CMOS technology. The simulated results show that the phase locking time of the proposed circuit is about 6.4 usec and power consumption is about 43uW at supply voltage of 3.3V.

• Journal of Sensor Science and Technology
• /
• v.12 no.4
• /
• pp.191-197
• /
• 2003

Due to explosive increase of internet usage, broadband data transmission using optical fibers is broadly used. In order to decrease distortion during long distance transmission, the optical signal need to be restored, typically, by converting the optical signal into the electrical signal. The optical signal is converted into the electrical signal using a photo-diode, and then a clock-and-recovery (CDR) circuit is used to recover the clock and retime the data. In this study, a clock-and-data recovery circuit has been designed using a standard 1.8 V $0.18\;{\mu}m$ CMOS process. With this CDR circuit, the improved phase detector and charge pump have been utilized. Also, by using a ring oscillator, the CDR circuit can recover clock and data from broadband multi-rate data ranging between 750 Mb/s and 2.85 Gb/s.

• Journal of IKEEE
• /
• v.14 no.1
• /
• pp.40-46
• /
• 2010

This paper describes a clock and data recovery (CDR) circuit that supports dual data rates of 2.7Gbps and 1.62Gbps for DisplayPort standard. The proposed CDR has a dual mode voltage-controlled oscillator (VCO) that changes the operating frequency with a "Mode" switch control. The chip has been implemented using $0.18{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of 37ps(@2.7Gbps) and 27ps(@1.62Gbps) in the recovered data. The power dissipation is 80mW at 2.7Gbps rate from a 1.8V supply.

• The Journal of the Korea Contents Association
• /
• v.10 no.2
• /
• pp.72-80
• /
• 2010

The 1Gbps clock and data recovery (CDR) circuit using the proposed multi-point phase detector (PD) is presented. The proposed phase detector generates up/down signals comparing 3-point that is data transition point and clock rising/falling edge. The conventional PD uses the pulse width modulation (PWM) that controls the voltage controlled oscillator (VCO) using the width of a pulse period's multiple. However, the proposed PD uses the pulse number modulation (PNM) that regulates the VCO with the number of half clock cycle pulse. Therefore the proposed PD can controls VCO preciously and reduces the jitter. The CDR circuit is tested using 1Gbps $2^{31}-1$ pseudo random bit sequence (PRBS) input data. The designed CDR circuit shows that is capable of recovering clock and data at rates of 1Gbps. The recovered clock jitter is 7.36ps at 1GHz and the total power consumption is about 12mW. The proposed circuit is implemented using a 0.18um CMOS process under 1.8V supply.