• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1277-1287
• /
• 2016

This study proposes a novel isolated high step-up galvanic converter, which is suitable for renewable energy applications and integrates a boost converter, a coupled inductor, a charge pump capacitor cell, and an LC snubber. The proposed converter comprises an input inductor and thus features a continuous input current, which extends the life of the renewable energy chip. Furthermore, the proposed converter can achieve a high voltage gain without an extremely large duty cycle and turn ratio of the coupled inductor by using the charge pump capacitor cell. The leakage inductance energy can be recycled to the output capacitor of the boost converter via the LC snubber and then transferred to the output load. As a result, the voltage spike can be suppressed to a low voltage level. Finally, the basic operating principles and experimental results are provided to verify the effectiveness of the proposed converter.

• Journal of IKEEE
• /
• v.19 no.4
• /
• pp.573-582
• /
• 2015

This paper presents the design of dual mode boost converter for energy harvesting. The designed converter boosts low voltage from energy harvester through a startup circuit. When the voltage goes above predefined value, supplied voltage to startup circuit is blocked by voltage detector. Boost controller makes the boosted voltage into $V_{OUT}$. The proposed circuit consists of oscillator for charge pump, charge pump, pulse generator, voltage detector, and boost controller. The proposed converter is designed and fabricated using a $0.18{\mu}m$ CMOS process. The designed circuit shows that minimum input voltage is 600mV, output is 3V and startup time is 20ms. The boost converter achieves 47% efficiency at a load current of 3mA.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1011-1014
• /
• 2004

In this paper, we present a new DC-DC converter for gate driver circuit in low temperature poly-Si TFT technology. It is composed of a newly developed charge pump circuit and a regulator circuit. When the input voltage is 5V, the efficiency of a positive charge pump used in the DC-DC converter and that of a negative charge pump is 69.0% and 57.1%, respectively. The output voltage of DC-DC converter varies 200mV when the target voltages of DC-DC converter are 9V, -6V and the threshold voltage of TFTs varies ${\pm}$ 0.5V.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.5
• /
• pp.1155-1161
• /
• 2014

This paper proposes a start-up voltage generator for reducing the minimum input supply voltage of DC-DC boost converters to 250mV. The proposed start-up voltage generator boosts 250mV input voltage to over 500mV to charge the capacitor for starting the boost converter. After the boost converter operates initially with the supply voltage charged in the capacitor, it uses its boosted output voltage for the supply voltage. Therefore, after the start-up operation, the proposed DC-DC boost converter works as the same as the conventional one. The proposed start-up voltage generator reduces the threshold voltage of the transistors by adjusting the body voltage at a low input voltage. This causes the higher clock frequency and the larger current to a Dickson charge-pump for boosting the input voltage. The proposed start-up voltage generator was implemented with a $0.18{\mu}m$ CMOS process. Its clock frequency and output voltage were 34.5kHz and 522mV at 250mV input voltage, respectively.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1468-1479
• /
• 2015

Renewable energy resources such as wind and photovoltaic power generation systems demand a high step-up DC-DC converters to convert the low voltage to commercial grid voltage. However, the high step-up converter using a transformer has limitations of high voltage stresses of switches and diodes when the transformer winding ratio increases. Accordingly, conventional studies have been applied to series-connect multioutput converters such as forward-flyback and switched-capacitor flyback to reduce the transformer winding ratio. This paper proposes new single-ended converter topologies of an isolation type and a non-isolation type to improve power efficiency, cost-effectiveness, and output ripple. The first proposal is an isolation-type charge-pump switched-capacitor flyback converter that includes an extreme-ratio isolation switched-capacitor cell with a chargepump circuit. It reduces the transformer winding number and the output ripple, and further improves power efficiency without any cost increase. The next proposal is a non-isolation charge-pump switched-capacitor-flyback tapped-inductor boost converter, which adds a charge-pump-connected flyback circuit to the conventional switched-capacitor boost converter to improve the power efficiency and to reduce the efficiency degradation from the input variation. In this paper, the operation principle of the proposed scheme is presented with the experimental results of the 100 W DC-DC converter for verification.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.10
• /
• pp.479-485
• /
• 2001

In this paper, we introduce a charge pump phase-locked loop (PLL) architecture which employs a precharge phase frequency detector (PFD) and a sequential PFD to achieve a high frequency operation and a fast acquisition. Operation frequency is increased by using the precharge PFD when the phase difference is within $-{\pi}{\sim}{\pi}$ and acquisition time is shortened by using the sequential PFD and the increased charge pump current when the phase difference is larger than ${\pm}{\pi}$. So error detection range of the proposed PLL structure is not limited to $-{\pi}{\sim}{\pi}$ and a high frequency operation and a higher speed lock-up time can be achieved. The proposed PLL was designed using 1.5 ${\mu}m$ CMOS technology with 5V supply voltage to verify the lock in process. The proposed PLL shows successful acquisition for 200 MHz input frequency. On the other hand, the conventional PLL with the sequential PFD cannot operate at up to 160MHz. Moreover, the lock-up time is drastically reduced from 7.0 ${\mu}s\;to\;2.0\;{\mu}s$ only if the loop bandwidth to input frequency ratio is regulated by the divide-by-4 counter during the acquisition process. By virtue of this dual PFDs, the proposed PLL structure can improve the trade-off between acquisition behavior and locked behavior.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2798-2800
• /
• 1999

A new circuit, modified valley fill (MVF) combined with resonant inductor of the self-excited resonant inverter and charge pump capacitors(CPCs), is presented to achieve high PF electronic ballast providing sufficient preheat current to lamp filaments for soft start maintaining low DC bus voltage. The MVF can adjust the valley voltage higher than half the peak line voltage. The CPCs draw the current from the input line to make up the current waveform during the valley interval. The measured PF and THD are 0.99 and 12%, respectively. The lamp current CF is also acceptable in the proposed circuit. The proposed circuit is suitable for implementing cost-effective electronic ballast.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.267-269
• /
• 2007

PLL(Phase Locked Loop) are widely used circuit technique in modern electronic systems. In this paper, We propose the low voltage and high speed PLL. We design the PFD(Phase Frequency Detector) by using TSPC (True Single Phase Clock) circuit to improve the performance and solve the dead-zone problem. We use CP(Charge Pump} and LP(Loop filter) for Negative feedback and current reusing in order to solve current mismatch and switch mismatch problem. The VCO(Voltage controlled Oscillator) with 5-stage differential ring oscillator is used to exact output frequency. The divider is implemented by using D-type flip flops asynchronous dividing. The frequency divider has a constant division ratio 32. The frequency range of VCO has from 200MHz to 1.1GHz and have 1.7GHz/v of voltage gain. The proposed PLL is designed by using 0.18um CMOS processor with 1.8V supply voltage. Oscillator's input frequency is 25MHz, VCO output frequency is 800MHz and lock time is 5us. It is evaluated by using cadence spectra RF tools.

• Journal of IKEEE
• /
• v.13 no.4
• /
• pp.63-68
• /
• 2009

The power management integrated circuit(PMIC) for CCD image sensor is presented in this study. A CCD image sensor is very sensitive against temperature. The temperature, that is heat, is generally generated by the PMIC with low efficiency. Since the generated heat influences performance of CCD image sensor, it should be minimized by using a PMIC which has a high efficiency. In order to develop the PMIC with high efficiency, the input stage is designed with synchronous type step down DC-DC converter. The operating range of the converter is from 5V to 15V and the converter is controlled using PWM method. The PWM control circuit consists of a saw-tooth generator, a band-gap reference circuit, an error amplifier and a comparator circuit. The saw-tooth generator is designed with 1.2MHz oscillation frequency. The comparator is designed with the two stages OP Amp. And the error amplifier has 40dB DC gain and $77^{\circ}$ phase margin. The output of the step down converter is connected to input stage of the charge pump. The output of the charge pump is connected to input of the LDO which is the output stage of the PMIC. Finally, the PMIC, based on the PWM control circuit and the charge pump and the LDO, has output voltage of 15V, -7.5V, 3.3V and 5V. The PMIC is designed with a 0.35um process.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1226-1235
• /
• 2016

For wearable health monitoring systems, a fundamental problem is the limited space for storing energy, which can be translated into a short operational life. In this paper, a highly efficient active voltage doubling rectifier with a wide input range for micro-piezoelectric energy harvesting systems is proposed. To obtain a higher output voltage, the Dickson charge pump topology is chosen in this design. By replacing the passive diodes with unbalanced-biased comparator-controlled active counterparts, the proposed rectifier minimizes the voltage losses along the conduction path and solves the reverse leakage problem caused by conventional comparator-controlled active diodes. To improve the rectifier input voltage sensitivity and decrease the minimum operational input voltage, two low power common-gate comparators are introduced in the proposed design. To keep the comparator from oscillating, a positive feedback loop formed by the capacitor C is added to it. Based on the SMIC 0.18-μm standard CMOS process, the proposed rectifier is simulated and implemented. The area of the whole chip is 0.91×0.97 mm², while the rectifier core occupies only 13% of this area. The measured results show that the proposed rectifier can operate properly with input amplitudes ranging from 0.2 to 1.0V and with frequencies ranging from 20 to 3000 Hz. The proposed rectifier can achieve a 92.5% power conversion efficiency (PCE) with input amplitudes equal to 0.6 V at 200 Hz. The voltage conversion efficiency (VCE) is around 93% for input amplitudes greater than 0.3 V and load resistances larger than 20kΩ.