• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.1
• /
• pp.63-67
• /
• 2009

Current mismatch in a charge pump causes degradation in spectral purity of the phase locked loops(PLLs), such as reference spurs. The current mismatch can be reduced by increasing the output resistance of the charge pump, as in a cascoded output stage. However as the supply voltage is lowered, it is hard to stack transistors. In this paper, a new method for reducing the current mismatch is proposed. The proposed method is based on a feed-forward compensation for the channel length modulation effect of the output stage. The new method has been demonstrated through simulations on typical $0.18{\mu}m$ CMOS circuits.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.20 no.7
• /
• pp.492-499
• /
• 2008

The cooling load in winter is significant in many commercial buildings and hotels because of the usage of office equipments and the high efficiency of wall insulation. The development of a multi-heat pump that can cover heating and cooling simultaneously for each indoor unit is required. In this study, the performance of a multi-heat pump with 3-piping system was investigated as a function of refrigerant charge and its performance was analyzed in cooling mode, heating mode, and heat recovery mode. COP in the heating or cooling mode showed little dependence on refrigerant charge at overcharge conditions, while those were strongly dependent on refrigerant charge at undercharge conditions and outdoor inlet temperature. In the heat recovery mode, the performance of the system was very sensitive to charge amount at all conditions. Optimum charge amount in the heat recovery mode was 14% lower than that in the cooling mode at the standard condition because the refrigerant only passed the indoor units. It is required to store the excessive refrigerant charge in a storage tank to optimize the system performance at operating modes.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.5
• /
• pp.241-249
• /
• 2015

Phase-locked-loops (PLL) have been employed in high-speed data transmission systems like wireless transceivers, disk read/write channels and high-speed interfaces. The majority of the researchers use a charge pump (CP) to obtain high performance from PLLs. This paper presents a review of various CMOS CP schemes that have been implemented for PLLs and the relationship between the CP parameters with PLL performance. The CP architecture is evaluated by its current matching, charge sharing, voltage output range, linearity and power consumption characteristics. This review shows that the CP has significant impact on the quality performance of CP PLLs.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.07a
• /
• pp.339-339
• /
• 2004

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.2
• /
• pp.133-138
• /
• 2017

This paper presents a jitter characteristic improved phase locked loop (PLL) with an RC time constant circuit. In the RC time constant circuit, LPF's voltage is inputted to a comparator through small and large RC time constant circuits. The signal through a small RC time constant circuit has almost same loop filter output voltage. The signal through a large RC time constant circuit has the average value of loop filter output voltage and does as a role of reference voltage to the comparator. The output of the comparator controls the sub-charge pump which provide a current to LPF. When the loop filter output voltage increases, the sub-charge pump discharges the loop filter and decreases loop filter output voltage. When the loop filter output voltage decreases, the sub-charge pump charges the loop filter and increases loop filter output voltage. The negative feedback loop reduces the variation of loop filter output voltage resulting in jitter characteristic improvement.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.05a
• /
• pp.671-674
• /
• 2009

We design a low-power and low-area asynchronous EEPROM of 256 bits used in a passive UHF RFID tag chip. For a low-power solution, we use a supply voltage of 1.8V and design a Dickson charge pump using N-type Schottky diodes with a low-voltage characteristic. And we use an asynchronous interface and a separate I/O method for a low-area solution of the peripheral circuit of the designed EEPROM. And we design a Dickson charge pump using N-type Schottky diodes to reduce an area of DC-DC converter. The layout area of the designed EEPROM of 256 bits with an array of 16 rows and 16 columns using $0.18{\mu}m$ EEPROM process is $311.66{\times}490.59{\mu}m^2$.

• International journal of advanced smart convergence
• /
• v.4 no.1
• /
• pp.64-70
• /
• 2015

This paper proposes fluorescent electronic ballast with high power factor and low line input current harmonics. The system performance can be improved by a charged pump circuit. Details of design and circuit operation are described. The proposed electronic ballast is modified from single-stage half bridge class D electronic ballast by adding capacitor parallel with each power switch and setting the circuit parameter to operate under class DE inverter condition. By using this proposed method the DC bus voltage can be reduced around by 50% compare with conventional class D inverter circuit. Because the power switches are operated at zero voltage switching condition and low dv/dt of class DE switching. The experimental results show that the proper frequency of the prototype is around 50 kHz with input power factor of 0.982, $THD_i$ 10.2% at full load and efficiency of more than 90%.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.12
• /
• pp.2716-2724
• /
• 2012

In this paper, a Phase Difference-to-Voltage Converter (PDVC) has been introduced into a conventional fractional-N PLL to suppress fractional spurs. The PDVC controls charge pump current depending on the phase difference of two input signals to phase frequency detector. The charge pump current decreases as the phase difference of two input signals increase. It results in the reduction of fractional spurs in the proposed fractional-N PLL. The proposed fractional-N PLL with PDVC has been designed based on a 1.8V $0.18{\mu}m$ CMOS process and proved by HSPICE simulation.

• Journal of Power Electronics
• /
• v.15 no.6
• /
• pp.1468-1479
• /
• 2015

Renewable energy resources such as wind and photovoltaic power generation systems demand a high step-up DC-DC converters to convert the low voltage to commercial grid voltage. However, the high step-up converter using a transformer has limitations of high voltage stresses of switches and diodes when the transformer winding ratio increases. Accordingly, conventional studies have been applied to series-connect multioutput converters such as forward-flyback and switched-capacitor flyback to reduce the transformer winding ratio. This paper proposes new single-ended converter topologies of an isolation type and a non-isolation type to improve power efficiency, cost-effectiveness, and output ripple. The first proposal is an isolation-type charge-pump switched-capacitor flyback converter that includes an extreme-ratio isolation switched-capacitor cell with a chargepump circuit. It reduces the transformer winding number and the output ripple, and further improves power efficiency without any cost increase. The next proposal is a non-isolation charge-pump switched-capacitor-flyback tapped-inductor boost converter, which adds a charge-pump-connected flyback circuit to the conventional switched-capacitor boost converter to improve the power efficiency and to reduce the efficiency degradation from the input variation. In this paper, the operation principle of the proposed scheme is presented with the experimental results of the 100 W DC-DC converter for verification.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.6
• /
• pp.416-424
• /
• 2014

This paper presents an 8-bit pipelined analog-to-digital converter. The supply voltage applied for comparators and other sub-blocks of the ADC were 0.7V and 0.5V, respectively. This low power ADC utilizes the capacitive charge pump technique combined with a source-follower and calibration to resolve the need for the opamp. The differential charge pump technique does not require any common mode feedback circuit. The entire structure of the ADC is based on fully dynamic circuits that enable the design of a very low power ADC. The ADC was designed to operate at 1MS/s in 90nm CMOS process, where simulated results using ADS2011 show the peak SNDR and SFDR of the ADC to be 47.8 dB (7.64 ENOB) and 59 dB respectively. The ADC consumes less than 1mW for all active dynamic and digital circuitries.