• Economic and Environmental Geology
• /
• v.54 no.6
• /
• pp.709-716
• /
• 2021

In this study, an adsorbent prepared by natural drying of iron hydroxide-based sludge collected from settling basin at a mine drainage treatment facility located in Gangneung, Gangwon-do was used to remove fluoride in an artificial fluoride solution and mine drainage, and the adsorption characteristics of the adsorbent were investigated. As a result of analyzing the chemical composition, mineralogical properties, and specific surface area of the adsorbent used in the experiment, iron oxide (Fe₂O₃) occupies 79.2 wt.% as the main constituent, and a peak related to calcite (CaCO₃) in the crystal structure analysis was analyzed. It was also identified that an irregular surface and a specific surface area of 216.78 m²·g^-1. In the indoor batch-type experiment, the effect of changes in reaction time, pH, initial fluoride concentration and temperature on the change in adsorption amount was analyzed. The adsorption of fluoride showed an adsorption amount of 3.85 mg·g^-1 16 hours after the start of the reaction, and the increase rate of the adsorption amount gradually decreased. Also, as the pH increased, the amount of fluoride adsorption decreased, and in particular, the amount of fluoride adsorption decreased rapidly around pH 5.5, the point of zero charge at which the surface charge of the adsorbent changes. Meanwhile, the results of the isotherm adsorption experiment were applied to the Langmuir and Freundlich isotherm adsorption models to infer the fluoride adsorption mechanism of the used adsorbent. To understand the thermodynamic properties of the adsorbent using the Van't Hoff equation, thermodynamic constants 𝚫H° and 𝚫G° were calculated using the adsorption amount information obtained by increasing the temperature from 25℃ to 65℃ to determine the adsorption characteristics of the adsorbent. Finally, the adsorbent was applied to the mine drainage having a fluoride concentration of about 12.8 mg·L^-1, and the fluoride removal rate was about 50%.

• Ecology and Resilient Infrastructure
• /
• v.8 no.4
• /
• pp.179-193
• /
• 2021

This study examines the use of satellite images for river classification and determination of stream reach, which is the first priority in the river environment assessment system. In the river environment assessment system used in South Korea, it is proposed to set a stream reach by using 10 or 25 times the width of the river based on the result of river classification. First, river classification for the main stream section of Cheongmi stream was performed using various river-related data. The maximum likelihood method was applied for land cover classification. In this study, Sentinel-2 satellite imagery, which is an open data technology with a resolution of 10 m, was used. A total of four satellite images from 2018 was used to consider various flow conditions: February 2 (daily discharge = 2.39 m³/s), May 23 (daily discharge = 15.51 m³/s), June 2 (daily discharge = 3.88 m³/s), and July 7 (daily discharge = 33.61 m³/s). The river widths were estimated from the result of land cover classification to determine stream reach. The results of the assessment reach classification were evaluated using indicators of stream physical environments, including pool diversity, channel sinuosity, and river crossing shape and structure. It is concluded that appropriate flow conditions need to be considered when using satellite images to set up assessment segments for the river environment assessment system.

• Journal of Korean Society of Disaster and Security
• /
• v.14 no.4
• /
• pp.69-80
• /
• 2021

This study tried to suggest improvement measures by discovering problems or matters requiring improvement among the annual regional safety evaluation systems. Briefly introducing the structure and contents of the study, which is the introduction, describes the regional safety evaluation method newly applied by the Ministry of Public Administration and Security in 2020. Utilization plans were also introduced according to the local safety level that was finally evaluated by the local government. In this paper, various views of previous researchers related to regional safety are summarized and described. In addition, problems were drawn in the composition of the index of local safety, the method of calculating the index, and the application of the current index. Next, the problems of specific regional safety evaluation indicators were analyzed and solutions were presented. First, "Number of semi-basement households" is replaced with "Number of households receiving basic livelihood" of 「Social Vulnerability Index」 in the field of disaster risk factors is replaced with "the number of households receiving basic livelihood". In addition, the "Vinyl House Area" is evaluated by replacing "the number of households living in a Vinyl House, the number of container households, and the number of households in Jjok-bang villages" with data. Second, in the management and evaluation of habitual drought disaster areas, local governments with a water supply rate of 95% or higher in Counties, Cities, and Districts are treated as "missing". This is because drought disasters rarely occur in the metropolitan area and local governments that have undergone urbanization. Third, the activities of safety sheriffs, safety monitor volunteers, and disaster safety silver monitoring groups along with the local autonomous prevention foundation are added to the evaluation of the evaluation index of 「Regional Autonomous Prevention Foundation Activation」 in the field of response to disaster prevention measures. However, since the name of the local autonomous disaster prevention organization may be different for each local government, if it is an autonomous disaster prevention organization organized and active for disaster prevention, it would be appropriate to evaluate the results by summing up all of its activities. Fourth, among the Scorecard evaluation items, which is a safe city evaluation tool used by the United Nations Office for Disaster Risk Reduction(UNDRR), the item "preservation of natural buffers to strengthen the protection functions provided by natural ecosystems" is borrowed, which is closely related to natural disasters. The Scorecard evaluation is an assessment index that focuses on improving the disaster resilience of local governments while carrying out the campaign "Creating cities resilient to climate crises and disasters" emphasized by UNDRR. Finally, the names of "regional safety level" and "local safety index" are similar, so the term of local safety level is changed to "natural disaster safety level" or "natural calamity safety level". This is because only the general public can distinguish the local safety level from the local safety index.

• Journal of Korean Elementary Science Education
• /
• v.41 no.4
• /
• pp.658-672
• /
• 2022

The unique teaching and learning difficulties of speed-related units in elementary school science are mainly due to the student's lack of mathematical thinking ability and procedural knowledge on speed measurement, and curriculums and textbooks must be constructed with these in mind. To identify the implications of composing a new science curriculum and relevant textbooks, this study reviewed the structure and contents of the speed-related units of three curriculums from the 2007 revised curriculum to the 2015 revised curriculum and the resulting textbooks and examined their relevance in light of the literature. Results showed that the current content carries the risk of making students calculate only the speed of an object through a mechanical algorithm by memorization rather than grasp the multifaceted relation between traveled distance, duration time, and speed. Findings also highlighted the need to reorganize the curriculum and textbooks to offer students the opportunity to learn the meaning of speed step-by-step by visualizing materials such as double number lines and dealing with simple numbers that are easy to calculate and understand intuitively. In addition, this paper discussed the urgency of improving inquiry performance such as process skills by observing and measuring an actual object's movement, displaying it as a graph, and interpreting it rather than conducting data interpretation through investigation. Lastly, although the current curriculum and textbooks emphasize the connection with daily life in their application aspects, they also deal with dynamics-related content somewhat differently from kinematics, which is the main learning content of the unit. Hence, it is necessary to reorganize the contents focusing on cases related to speed so that students can grasp the concept of speed and use it in their everyday lives. With regard to the new curriculum and textbooks, this study proposes that students be provided the opportunity to systematically and deeply study core topics rather than exclude content that is difficult to learn and challenging to teach so that students realize the value of science and enjoy learning it.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.6
• /
• pp.853-860
• /
• 2022

The purpose of this study is to suggest an improvement plan for the calculation method of the engineer standard wage rate (ESWR) and to compute a reasonable ESWR. To this end, an adequacy review of theESWR calculation criteria was conducted along with an extensive engineering industry survey. The survey results were analyzed using an effective response sample of 748 companies out of 1,000 survey samples extracted by stratifying the 5,879 survey population. The main results were as follows. ①When calculating the engineering service fee, the prime contractor's engineer wage is suitable for the ESWR. The ESWR can be estimated by the formula 'average wage÷[1-proportion of subcontract orders×(1-subcontract rate)].' ② The field survey showed that the number of monthly working days was 20.35-20.54 days at 99 % confidence interval, which was significantly different from the current standard (22 days). In addition, as a result of a legal review of the ESWR criteria, it was found that the number of working days should be calculated in accordance with the Labor Standards Act after 2022. ③ Applying government guidelines, the time difference between the wage survey and the ESWR application can be corrected by the past ESWR increase rate for a specific period. ④ Using modeling based on the analysis above, the current ESWR was 13.5-14.5 % lower than the appropriate level. A lower ESWR was driven by the non-reflection of subcontract structure (4.1 %), overestimation of monthly work days (6.8-7.8 %), and application of past wage (2.6 %). The proposed model is expected to be widely used in policy making, as it can provide a useful framework for calculating the standard wage rate in similar industries as well as calculating appropriate engineering fees.

• Korean Journal of Mineralogy and Petrology
• /
• v.35 no.4
• /
• pp.409-421
• /
• 2022

Achieving a highly resolved spatial distribution of Mn-bearing minerals and elements in the natural ferromanganese nodules can provide detailed knowledge of the temporal variations of geochemical conditions affecting the formation processes of nodules. While a recent study utilizing Raman spectroscopy has reported the changes in the manganate mineral phases with growth for spherical nodules from the Arctic Sea, the distributions of minerals and elements in the nodules from the shallow Arctic Sea with non-spherical forms have not yet fully elucidated. Here, we reported the micro-laser Raman spectra with varying data acquisition points along three different profiles from the center to the outermost rim of the non-spherical ferromanganese nodules collected from the East Siberian Sea (~73 m). The elemental distributions in the nodule (such as Mn, Fe, etc.) were also investigated by energy dispersive X-ray spectroscopy (EDS) analysis to observe the internal structure and mineralogical details. Based on the microscopic observation, the internal structures of a non-spherical nodule can be divided into three different regions, which are sediment-rich core, iron-rich substrate, and Mn-Fe layers. The Raman results show that the Mn-bearing mineral phases vary with the data acquisition points in the Mn-Fe layer, suggesting the changes in the geochemical conditions during nodule formation. In addition, we also observe that the mineral composition and structural characteristics depend on the profile direction from the core to the rim. Particularly, the Raman spectra obtained along one profile show the lack of Fe-(oxy)hydroxides and the noticeably high crystallinity of Mn-bearing minerals such as birnessite and todorokite. On the other hand, the spectra obtained along the other two profiles present the presence of significant amount of amorphous or poorly-ordered Fe-bearing minerals and the low crystallinity of Mn-bearing minerals. These results suggest that the diagenetic conditions varied with the different growth directions. We also observed the presence of halite in several layers in the nodule, which can be evidence of the alteration of seawater after nodule formation. The current results can provide the opportunity to obtain detailed knowledge of the formation process and geochemical environments recorded in the natural non-spherical ferromanganese nodule.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.7
• /
• pp.49-62
• /
• 2022

The hollow modular concrete block reinforced foundation method is one of the ground reinforcement foundation methods that uses hexagonal honeycomb-shaped concrete blocks with mixed crushed rock to reinforce soft grounds. It then forms an artificial layered ground that increases bearing capacity and reduces settlement. The hollow modular honeycomb-shaped concrete block is a geometrically economical, stable structure that distributes forces in a balanced way. However, the behavioral characteristics of hollow modular concrete block reinforced foundations are not yet fully understood. In this study, a bearing capacity test is performed to analyze the reinforcement effectiveness of the hollow modular concrete block through the laboratory model tests. From the load-settlement curve, punching shear failure occurs under the unfilled sand condition (A-1-N). However, the filled sand condition (A-1-F) shows a linear curve without yielding, confirming the reinforcement effect is three times higher than that of unreinforced ground. The bearing capacity equation is proposed for the parts that have contact pressure under concrete, vertical stress of hollow blocks, and the inner skin friction force from horizontal stress by confining effect based on the schematic diagram of confining effect inside a hollow modular concrete block. As a result of calculating the bearing capacity, the percentage of load distribution for contact force on the area of concrete is about 65%, vertical force on the area of hollow is 16.5% and inner skin friction force of area of the inner wall is about 18.5%. When the surcharge load is applied to the concrete part, the vertical stress occurs on the area of the hollow part by confining effect first. Then, in the filled sand in the hollow where the horizontal direction is constrained, the inner skin friction force occurs by the horizontal stress on the inner wall of the hollow modular concrete block. The inner skin friction force suppresses the punching of the concrete part and reduces contact pressure.

• Korean Chemical Engineering Research
• /
• v.60 no.3
• /
• pp.347-355
• /
• 2022

The safety valve (PSV) is a safety device that automatically releases a spring when the pressure generated by various causes reaches the set pressure, and is restored to a normal state when the pressure falls below a certain level. Periodic inspection and monitoring of safety valves are essential so that they can operate normally in abnormal conditions such as pressure rise. However, as the current safety inspection is performed only at a set period, it is difficult to ensure the safety of normal operation. Therefore, evaluation items were developed by finding failure modes and causative factors of safety valves required for safety management. In addition, it is intended to provide decision-making information for securing safety by deriving the priority of items. To this end, a Delphi survey was conducted three times to derive evaluation factors that were judged to be important in relation to the Failure Mode Cause Factor (FMCFs) of the safety valve (PSV) targeting 15 experts. As a result, 6 failure modes of the safety valve and 22 evaluation factors of its sub-factors were selected. In order to analyze the priorities of the evaluation factors selected in this way, the hierarchical structure was schematized, and the hierarchical decision-making method (AHP) was applied to the priority calculation. As a result of the analysis, the failure mode priorities of FMCFs were 'Leakage' (0.226), 'Fail to open' (0.201), 'Fail to relieve req'd capacity' (0.152), 'Open above set pressure' (0.149), 'Spuriously' 'open' (0.146) and 'Stuck open' (0.127) were confirmed in the order. The lower priority of FMCFs is 'PSV component rupture' (0.109), 'Fail to PSV size calculation' (0.068), 'PSV Spring aging' (0.065), 'Erratic opening' (0.059), 'Damage caused by improper installation and handling' (0.058), 'Fail to spring' (0.053), etc. were checked in the order. It is expected that through efficient management of FMCFs that have been prioritized, it will be possible to identify vulnerabilities of safety valves and contribute to improving safety.

• Informatization Policy
• /
• v.29 no.1
• /
• pp.24-37
• /
• 2022

Amid rapid changes in the ICT environment attributed to the 4th Industrial Revolution, the development of information & communication technology, and COVID-19, the existing internet developed without considering security, mobility, manageability, QoS, etc. As a result, the structure of the internet has become complicated, and problems such as security, stability, and reliability vulnerabilities continue to occur. In addition, there is a demand for a new concept of the internet that can provide stability and reliability resulting from digital transformation-geared advanced technologies such as artificial intelligence and IoT. Therefore, in order to suggest a way of implementing the Korean future internet that can strengthen cybersecurity, this study suggests the direction and strategy for promoting the future internet that is suitable for the Korean cyber environment through analyzing important key factors in the implementation of the future internet and evaluating the trend and suitability of domestic & foreign research related to future internet. The importance of key factors in the implementation of the future internet proceeds in the order of security, integrity, availability, stability, and confidentiality. Currently, future internet projects are being studied in various ways around the world. Among numerous projects, Bright Internet most adequately satisfies the key elements of future internet implementation and was evaluated as the most suitable technology for Korea's cyber environment. Technical issues as well as strategic and legal issues must be considered in order to promote the Bright Internet as the frontrunner Korean future internet. As for technical issues, it is necessary to adopt SAVA IPv6-NID in selecting the Bright Internet as the standard of Korean future internet and integrated data management at the data center level, and then establish a cooperative system between different countries. As for strategic issues, a secure management system and establishment of institution are needed. Lastly, in the case of legal issues, the requirement of GDPR, which includes compliance with domestic laws such as Korea's revised Data 3 Act, must be fulfilled.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.24-48
• /
• 2022

Bronze mirrors found in pagodas were regarded as simple offerings and thus have received little attention in studies. Furthermore, the few studies on bronze mirrors enshrined in pagodas have focused on the line-engraved mirrors found in the pagodas of the Kingdom of Wuyue; therefore, it is difficult to understand the general characteristics of the bronze mirrors enshrined in the pagodas. This study assumes that the bronze mirrors found in many pagodas in the Kingdom of Wuyue and the Song dynasty were enshrined for a specific purpose. To explore this assumption and accurately understand the artifacts, this study focuses on the location and method of enshrinement. The number of bronze mirrors enshrined in pagodas increased during the Kingdom of Wuyue, with the mirrors expressing statues and inscriptions related to Buddhism rather than being simple offerings. This shows that the purpose of the bronze mirror changed. The influence of the Kingdom of Wuyue continued during the Song dynasty; however, the pattern of bronze mirror enshrinement changed due to the culture and social atmosphere of the time. The most common types of enshrined bronze mirrors were plain, and bronze mirrors from the Dang dynasty were also used consistently. Plain bronze mirrors were used more frequently in this period despite the lingering influence of the Kingdom of Wuyue because it was less laborious to engrave images and inscriptions such as the inscription of Buddha. Additionally, bronze mirrors were valued during this period because of the attention toward the imitation of the archaic bronze(仿古銅器) of the Song dynasty and the influence of the emperor. Moreover, it is believed that bronze mirrors were enshrined in pagodas as offerings as they were deemed valuable at the time. There was a change in the method of enshrining bronze mirrors in pagodas during the Kingdom of Wuyue and the Song dynasty. During this time, bronze mirrors that were positioned on the floor or in iron boxes were intentionally attached to walls or hung from the ceiling. This method was largely divided into two types: attaching to walls or the ceiling(嵌入鏡) and hanging from the ceiling(懸鏡). A typical example of hanging a bronze mirror from the ceiling can be seen in the Jingzhisa Temple Pagoda, and Teng County's Fushengsa Temple Pagoda contains an example of attaching a bronze mirror to the ceiling. The methods of hanging or attaching bronze mirrors to the ceiling were closely related to the methods employed in Chinese tombs. Song dynasty burial chambers had a high and wide structure, so to defend against evil spirits(辟邪用), bronze mirrors were used to protect the burial rooms. Bronze mirrors were, therefore, placed high to illuminate the burial room. This was achieved in the ways mentioned above. As underground chambers became wider and higher, mirrors also protected the important areas of the chambers and illuminated the interiors. Thus, it is believed that the methods of enshrining bronze mirrors in the pagodas during the Kingdom of Wuyue and the Song dynasty arose from the method of enshrining bronze mirrors in tombs at the time. Thereafter, pagodas, such as the Miaojuesa Temple Pagoda, in which the placement of a bronze mirror was actively considered from the design stage were constructed.