• Journal of Korean Institute of Industrial Engineers
• /
• v.39 no.5
• /
• pp.367-373
• /
• 2013

In this article, we deal with a design problem for determining the levels of noise factors in the Taguchi method. First, the proposed levels by Taguchi method is reviewed in case of smaller-the-better performance characteristics. We obtain the optimal levels of noise factors minimizing the mean square error of SN(signal to Noise) ratio and compare the optimal levels with the levels proposed by Taguchi method under the first and second order models. Secondly, the concept of V-optimality is applied to determining the levels of noise factors.

• Journal of Korean Society for Quality Management
• /
• v.31 no.4
• /
• pp.150-163
• /
• 2003

The purpose of this paper is to propose an interactive method using the concept of Signal­to­Noise (SN) ratios and cutting ranges for selecting the most preferred alternatives of Multiple­attribute Decision­Making(MADM) with the­smaller­the­better or the­larger­the­better characteristics. In this method the decision makers could make a grouping of attributes by their priorities. This research is based on the assumption of an equality between the attributes of MADM with the characteristics of Taguchi method. As a result, this interactive method could transform the characteristic value of Taguchi method into the size of SN ratios which are relatively easy to understand by decision makers.

• Proceedings of the Safety Management and Science Conference
• /
• 2003.05a
• /
• pp.1-5
• /
• 2003

We purpose a decision model to select the optimal facilities for the Decision Making problems with multiple characteristics(nominal-is-best characteristics, larger-is -better characteristics, smaller- is -better characteristics). Using this model, concept of the loss function is used in this comprehensive method of for select the optimal preferred facilities. To solve the issue on the optimal preferred facilities for multiple characteristics, this study propose the loss function with cross-product terms among the characteristics and derived range of the coefficients of the terms.

• The Magazine of the IEIE
• /
• v.37 no.8
• /
• pp.50-59
• /
• 2010

$0.18-{\mu}m$ high voltage technology 13.5V high voltage well-based symmetric EDMOS isolated by MTI was designed and fabricated. Using calibrated process and device model parameters, the characteristics of the symmetric and asymmetric EDMOS have been simulated. The asymmetric EDMOS has higher performance, better $R_{sp}$ / BVDSS figure-of-merit, short-channel immunity and smaller pitch size than the symmetric EDMOS. The asymmetric EDMOST is a good candidate for low-power and smaller source driver chips. The low voltage logic well-based EDMOS process has advantages over high voltage well-based EDMOS in process cost by eliminating the process steps of high-voltage well/drift implant, high-temperature long-time thermal steps, etc. The specific on-resistance of our well-designed logic well-based EDMOSTs is compatible with the smallest one published. TCAD simulation and measurement results show that the improved logic well-based nEDMOS has better electrical characteristics than those of the conventional one. The improved EDMOS proposed in this paper is an excellent candidate to be integrated with low voltage logic devices for high-performance low-power low-cost chips.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.05a
• /
• pp.93-97
• /
• 2008

The study analyzed on each kind of basic characteristics in mortar to prove an effect of pre-mix cement, ultra high strength binder. The results were as follows. in characteristics of not set mortar, fluidity time was the quickest at the time of using POBSA and was more delayed at the time of using Fly Ash than at the time of using Blast Furnace Slag as a binder. Mortar ring flow and flow con flow got smaller as fluidity time got longer, on the contrary to fluidity time. Unit capacity mass was smaller at the time of using Fly Ash than at the time of using Blast Furnace Slag. According to pre-mix, it was difficult to discover a regular tendency. In characteristics of hardening mortar, the 28th day compressive strength was better than thing mixed after measuring separately in pre-mix. According to a binder's kind, Silica Fume B, C was better than Silica Fume A.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.29-34
• /
• 2012

This study describes the selection of optimum machining conditions for a high-hardness resin by using a large 5-axis machine. The experiments were conducted to examine the main factors that affect the surface roughness, such as the spindle speed, axial and radial depths of the cut, and pattern of the cutter path. To analyze the experiment results, the factor with the biggest impact on machining was determined using the smaller-the-better characteristic of the Taguchi method; the effectiveness of the experiment was then confirmed by verifying the selected optimum machining condition.

• Journal of Korean Society for Quality Management
• /
• v.38 no.3
• /
• pp.408-412
• /
• 2010

In this note, we deal with a design problem for determining the levels of noise factors in the Taguchi method. Recently, Ree(2009) proposed a new method to determine the levels of noise factors that is dependent on the distribution of the noise factors. We discuss the original suggestion from Taguchi method, propose a way to compare the two methods and investigate the performance(mean square error) of two proposals by examples.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.4
• /
• pp.29-32
• /
• 2004

Fully depleted Silicon-on-Insulator (FD-SOI) devices lead to better electrical characteristics than bulk CMOS devices. However, the presence of a thin top silicon layer and a buried SiO2 layer causes self-heating due to the low thermal conductivity of the buried oxide. The electrical characteristics of FDSOI devices strongly depend on the path of heat dissipation. In this paper, we present a new three-dimensional (3-D) analysis technique for the self-heating effect of the finger-type and bar-type transistors. The 3-D analysis results show that the drain current of the finger-type transistor is 14.7% smaller than that of the bar-type transistor due to the 3-D self-heating effect. We have learned that the rate of current degradation increases significantly when the width of a transistor is smaller that a critical value in a finger-type layout. The current degradation fro the 3-D structures of the finger-type and bar-type transistors is investigated and the design issues are also discussed.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.3 s.192
• /
• pp.76-83
• /
• 2007

The Taguchi method is applied to obtain the optimal design of an automotive pedal arm in consideration of the stiffness test specification. Design parameters are defined to describe shape of the pedal arm. Volume, maximum Von-Mises stress and maximum displacement of the pedal arm are established as the smaller-the-better characteristics. Optimal parameters are determined on the basis of the analyzed level averages of the characteristics.

• Journal of the Optical Society of Korea
• /
• v.18 no.3
• /
• pp.207-216
• /
• 2014

In this work, we report detailed numerical analysis of the near-elliptic core index-guiding triangular-lattice and square-lattice photonic crystal fiber (PCFs); where we numerically characterize the birefringence, single mode, cut-off behavior and group velocity dispersion and effective area properties. By varying geometry and examining the modal field profile we find that for the same relative values of $d/{\Lambda}$, triangular-lattice PCFs show higher birefringence whereas the square-lattice PCFs show a wider range of single-mode operation. Square-lattice PCF was found to be endlessly single-mode for higher air-filling fraction ($d/{\Lambda}$). Dispersion comparison between the two structures reveal that we need smaller lengths of triangular-lattice PCF for dispersion compensation whereas PCFs with square-lattice with nearer relative dispersion slope (RDS) can better compensate the broadband dispersion. Square-lattice PCFs show zero dispersion wavelength (ZDW) red-shifted, making it preferable for mid-IR supercontinuum generation (SCG) with highly non-linear chalcogenide material. Square-lattice PCFs show higher dispersion slope that leads to compression of the broadband, thus accumulating more power in the pulse. On the other hand, triangular-lattice PCF with flat dispersion profile can generate broader SCG. Square-lattice PCF with low Group Velocity Dispersion (GVD) at the anomalous dispersion corresponds to higher dispersion length ($L_D$) and higher degree of solitonic interaction. The effective area of square-lattice PCF is always greater than its triangular-lattice counterpart making it better suited for high power applications. We have also performed a comparison of the dispersion properties of between the symmetric-core and asymmetric-core triangular-lattice PCF. While we need smaller length of symmetric-core PCF for dispersion compensation, broadband dispersion compensation can be performed with asymmetric-core PCF. Mid-Infrared (IR) SCG can be better performed with asymmetric core PCF with compressed and high power pulse, while wider range of SCG can be performed with symmetric core PCF. Thus, this study will be extremely useful for designing/realizing fiber towards a custom application around these characteristics.