• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.190-190
• /
• 2010

Zinc oxide is the most attractive material due to the large direct band gap (3.37 eV), excellent chemical and thermal stability, and large exciton binding energy (60 meV). Recently, ZnO nanorods were used as the high efficient antireflection coating layer of solar cells based on silicon (Si). In this reports, we studied the effects of rapid thermal annealing (RTA) treatment on optical properties of ZnO nanorods. For fabrication of ZnO nanorods, there are many methods such as hydrothermal method, sol-gel method, and metal organic chemical vapor deposition method. Among of them, we used the conventional wet chemical method which is simple and low temperature growth. In order to synthesize the ZnO nanorods, the ZnO films were deposited on Si substrate by RF magnetron sputtering at room temperature and the samples were dipped to aqua solution containing the zinc nitrate and hexamethylentetramines (HMT). The synthesis process was achieved in keeping with temperature of $90-95^{\circ}C$ and under constant stirring. The morphology of ZnO nanorods on glass and Si was characterized by scanning electron microscopy. For the analysis of antireflection performance, the reflectance and transmittance were measured by spectrophotometer. And for analyzing the effects of RTA treatment on ZnO nanorods, crystalline properties were investigated by X-ray diffraction measurements and optical properties was estimated by photoluminescence spectra.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.90.2-90.2
• /
• 2013

Vertically-aligned silicon nanostructure arrays (SNAs) have been drawing much attention due to their useful electrical properties, large surface area, and quantum confinement effect. SNAs are typically fabricated by chemical vapor deposition, reactive ion etching, or wet chemical etching. Recently, metal-assisted chemical etching process, which is relatively simple and cost-effective, in combination with nanosphere lithography was recently demonstrated for vertical SNA fabrication with controlled SNA diameters, lengths, and densities. However, this method exhibits limitations in terms of large-area preparation of unperiodic nanostructures and SNA geometry tuning independent of inter-structure separation. In this work, we introduced the layerby- layer deposition of polyelectrolytes for holding uniformly dispersed polystyrene beads as mask and demonstrated the fabrication of well-dispersed vertical SNAs with controlled geometric parameters on large substrates. Additionally, we present a new means of building in vitro neuronal networks using vertical nanowire arrays. Primary culture of rat hippocampal neurons were deposited on the bare and conducting polymer-coated SNAs and maintained for several weeks while their viability remains for several weeks. Combined with the recently-developed transfection method via nanowire internalization, the patterned vertical nanostructures will contribute to understanding how synaptic connectivity and site-specific perturbation will affect global neuronal network function in an extant in vitro neuronal circuit.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.200.1-200.1
• /
• 2013

실리콘 태양전지 표면에는 구조적인 결함에 의해 소수 캐리어의 재결합이 일어난다. 재결합에 의해 캐리어의 반송자 수명은 줄어들게 되고, 태양전지의 효율은 감소하게 된다. 이를 줄이기 위해 태양전지 전 후면에 패시베이션을 하게 되는데, 이번 연구는 단결정 실리콘 태양전지 전면에 SiNx막을 증착함으로 수소 패시베이션이 반송자 수명에 미치는 영향에 대하여 연구하였다. 공정을 위해 $156{\times}156mm^2$, 200 ${\mu}m$, 0.5-3.0 ${\Omega}{\cdot}cm$ and p-type 단결정 실리콘 웨이퍼를 사용하였고, SiNx막을 올리기 전에 KOH 8.5% 용액으로 SDR을 실행하였다. RF-PECVD 장비로 SiNx 막을 증착하였고 증착 온도는 $200{\sim}400^{\circ}C$, 반응기 내부의 압력을 200~1,000 mtorr, SiH4/NH3/N2 각각의 가스 비율 조절, 그리고 플라즈마 RF power 변화시킴에 따라 증착된 SiNx막의 균일도 및 특성을 분석하였다. 반사광 측정 장비인 Reflectometer장비로 막의 두께와 굴절률, 반사율을 측정하였고, 반송자 수명을 측정하여 태양전지의 표면결함을 최대한 패시베이션 시켜주는 조건에 대한 연구를 수행하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.12
• /
• pp.2247-2252
• /
• 2008

The SiOC films as the carbon doped silicon oxide film were prepared with the variation of flow rater ratios by plasma enhanced chemical vapor deposition. The samples were analyzed by the fourier transform infrared spectroscopy, I-V measurement and scanning electron microscopy. The samples were shown the chemical shift according to the flow rate ratios, and the grain did not formed at the sample with hybrid properties. The leakage currents decreased according to the increasing of the substrate temperature at the sample with hybrid properties, but the potential barrier increased.

• Korean Journal of Metals and Materials
• /
• v.48 no.7
• /
• pp.660-666
• /
• 2010

30 nm thick Ni layers were deposited on a glass substrate by e-beam evaporation. Subsequently, 30 nm or 60 nm ${\alpha}-Si:H$ layers were grown at low temperatures ($<220^{\circ}C$) on the 30 nm Ni/Glass substrate by catalytic CVD (chemical vapor deposition). The sheet resistance, phase, microstructure, depth profile and surface roughness of the $\alpha-Si:H$ layers were examined using a four-point probe, HRXRD (high resolution Xray diffraction), Raman Spectroscopy, FE-SEM (field emission-scanning electron microscopy), TEM (transmission electron microscope) and AES depth profiler. The Ni layers reacted with Si to form NiSi layers with a low sheet resistance of $10{\Omega}/{\Box}$. The crystallinty of the $\alpha-Si:H$ layers on NiSi was up to 60% according to Raman spectroscopy. These results show that both nano-scale NiSi layers and crystalline Si layers can be formed simultaneously on a Ni deposited glass substrate using the proposed low temperature catalytic CVD process.

• Korean Journal of Materials Research
• /
• v.31 no.7
• /
• pp.403-408
• /
• 2021

Various surface colors are predicted and implemented using the interference color generated by controlling the thickness of nano-level diamond like carbon (DLC) thin film. Samples having thicknesses of up to 385 nm and various interference colors are prepared using a single crystal silicon (100) substrate with changing processing times at low temperature by plasma-enhanced chemical vapor deposition. The thickness, surface roughness, color, phases, and anti-scratch performance under each condition are analyzed using a scanning electron microscope, colorimeter, micro-Raman device, and scratch tester. Coating with the same uniformity as the surface roughness of the substrate is possible over the entire experimental thickness range, and more than five different colors are implemented at this time. The color matched with the color predicted by the model, assuming only the reflection mode of the thin film. All the DLC thin films show constant D/G peak fraction without significant change, and have anti-scratch values of about 19 N. The results indicate the possibility that nano-level DLC thin films with various interference colors can be applied to exterior materials of actual mobile devices.

• Journal of the Korean Vacuum Society
• /
• v.21 no.3
• /
• pp.178-184
• /
• 2012

Carbon coils could be synthesized on nickel catalyst layer-deposited silicon oxide substrate using $C_2H_2$ and $H_2$ as source gases and $SF_6$ as an additive gas under thermal chemical vapor deposition system. The characteristics (formation density and morphology) of as-grown carbon coils were investigated as functions of additive gas flow rate and the cycling on/off modulation of $C_2H_2/SF_6$ flows. Even in the lowest $SF_6$ flow rate (5 sccm) in this work, the cycling on/off modulation injection of $SF_6$ flow for 2 minutes could give rise to the formation of nanosized carbon coils, whereas the continuous injection of $SF_6$ flow for 5 minutes could not give rise to the carbon coils formation. With increasing $SF_6$ flow rates from 5 to 30 sccm, the cycling on/off modulation injection of $SF_6$ flow confines the geometry for the carbon coils to the nanosized ones. Fluorine's role of $SF_6$ during the reaction was regarded as the main cause for the confinement of carbon coils geometries to the nano-sized ones.

• Journal of the Korean Vacuum Society
• /
• v.21 no.1
• /
• pp.48-54
• /
• 2012

Carbon coils could be synthesized on nickel catalyst layer-deposited silicon oxide substrate using $C_2H_2$ and $H_2$ as source gases and SF6 as an additive gas under thermal chemical vapor deposition system. The geometries of as-grown carbon materials were investigated with increasing the reaction temperature as the increment of $25^{\circ}C$ from $650^{\circ}C$ up to $800^{\circ}C$. At $650^{\circ}C$, the embryos for carbon coils were formed. With increasing the reaction temperature to $700^{\circ}C$, the coil-type geometries were developed. Further increasing the reaction temperature to $775^{\circ}C$, the development of wave-like nano-sized coils, instead of nano-sized coils, and occasional appearance of micro-sized carbon coils could be observed. Fluorine in $SF_6$ additive may shrink the micro-sized coil diameter via the reduction of Ni catalyst size by fluorine's etching role. Finally, the preparation of the micro-sized carbon coils having the smaller coil diameters, compared with the previously reported ones, could be possible using $SF_6$ additive.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.6
• /
• pp.215-219
• /
• 2016

Vanadium-doped SiC crystals have been grown by using a porous graphite inner crucible filled with vanadium carbide (VC) and by using a porous graphite plate and SiC + VC powders, respectively. Semi-insulating SiC crystals were grown onto the 6H-SiC seed crystals by PVT (Physical Vapor Transport) method. The grown crystals were indicated to be 6H-SiC polytype by XRD. As result of SIMS analysis, vanadium-rich precipitates were observed when the vanadium concentration was relatively higher than the maximum solubility of vanadium ($3-5{\times}10^{17}cm^{-3}$) in vanadium-doped SiC crystals, which resulted in degradation of crystal quality.

• Journal of the Korean Ceramic Society
• /
• v.34 no.2
• /
• pp.131-138
• /
• 1997

Silicon carbide films were chemically vapor deposited onto graphite substrates using MTS(Ch3SiCl3) as a source and Ar or H2 as a diluent gas. The experiments were performed at a fixed condition such as a de-position temperature of 130$0^{\circ}C$, a total pressure of 10 torr, and a flow rate of 100 sccm for each MTS and carrier gas. The purpose of this study is to consider the variation of the growth behavior with the addition of each diluent gas. It is shown that the deposition rate leads to maximum value at 200 sccm addition ir-respective of diluent gases and the deposition rate of Ar addition is faster than that of H2 one. It seems that these characteristics of deposition rate are due to varying interrelationship between boundary layer thick-ness and the concentration of a source with each diluent gas addition, when overall deposition rate is con-trolled by mass transport kinetics. The preferred orientation of (220) plane was maintained for the whole range of Ar addition. However, above 200 sccm addition, especially that of (111) plane was more increased in proportion to H2 addition. Surface morphologies of SiC films were the facet structures under Ar addition, but those were gradually changed from facet to smooth structures with H2 addition. Surface roughness be-came higher in Ar, but it became lower in H2 with increasing the amount of diluent gas.