• Proceedings of the KIEE Conference
• /
• 2007.11a
• /
• pp.120-121
• /
• 2007

In this paper, ZnO thin films were deposited by pulsed laser deposition (PLD) on $Al_2O_3$ (alumina) at room temperature in various $O_2$ ambient. Rapid thermal annealing (RTA) has been performed at temperatures from $400^{\circ}C$ to $700^{\circ}C$. The effects of temperature and ambient on the structural property of ZnO films were examined by x-ray diffractometer (XRD) and atomic force microscopy (AFM), respectively. The results show that the (002)-oriented ZnO thin films on non-single crystal alumina were obtained in over 30mTorr ambient at all RTA temperatures including room temperature. The foil-width half maximum (FWHM) of (002) peak decreases as the RTA temperature increases, which indicates that ZnO thin films with RTA have improved crystalline quality.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.37-42
• /
• 2004

Shallow $p^{＋}$-n junctions were formed by preamorphization, low-energy ion implantation and dual-step annealing processes. Germanium ions were implanted into silicon substrates for preamorphization. The dopant implantation was performed into the preamorphized and non-preamorphized substrates using B $F_2$2 ions. Rapid thermal anneal (RTA) and furnace anneal (FA) were employed for dopant activation and damage removal. Samples were annealed by one of the following four methods; RTA(75$0^{\circ}C$/10s)＋Ft FA＋RTA(75$0^{\circ}C$/10s), RTA(100$0^{\circ}C$/10s)＋FA, FA＋The Ge Preamorphized sample exhibited a shallower junction depth than the non-preamorphized sample. When the employed RTA temperature was 100$0^{\circ}C$, FA＋RTA annealing sequence exhibited better junction characteristics than RTA＋FA thermal cycle from the viewpoint of junction depth, sheet resistance, $R_{s}$$.$ $x_{j}$, and leakage current.t.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.2
• /
• pp.83-88
• /
• 2005

The interface-states between the top silicon layer and buried oxide layer of nano-SOI substrate were developed. Also, the effects of thermal treatment processes on the interface-state distributions were investigated for the first time by using pseudo-MOSFETs. We found that the interface-state distributions were strongly influenced by the thermal treatment processes. The interface-states were generated by the rapid thermal annealing (RTA) process. Increasing the RTA temperature over $800^{\circ}C$, the interface-state density considerably increased. Especially, a peak of interface-states distribution that contributes a hump phenomenon of subthreshold curve in the inversion mode operation of pseudo-MOSFETs was observed at the conduction band side of the energy gap, hut it was not observed in the accumulation mode operation. On the other hand, the increased interface-state density by the RTA process was effectively reduced by the relatively low temperature annealing process in a conventional thermal annealing (CTA) process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.2
• /
• pp.26-32
• /
• 2021

The photovoltaic properties and microstructure changes were observed while perovskite solar cells (PSCs) with a fabricated carbon electrode were formed using the following annealing processes: hot-plate, oven, and rapid thermal annealing (RTA). Perovskite solar cells with a glass/FTO/compact TiO2/meso TiO2/meso ZrO2/carbon structure were prepared. The photovoltaic properties and microstructure changes in the PSCs were analyzed using a solar simulator, optical microscopy, and field emission scanning electron microscopy. An analysis of the photovoltaic properties revealed outstanding properties when RTA was applied to the cells. Microstructure analysis showed that perovskite was formed locally on the carbon electrode surface when hot-plate and oven annealing were applied. On the other hand, PSC with RTA showed a flat surface without extra perovskite agglomeration. Denser perovskite formed on the porous carbon electrode layer with RTA showed superior photovoltaic properties. These results suggest that the RTA process might be appropriate for the massive production of carbon electrode PSCs considering the processing time.

• Korean Journal of Materials Research
• /
• v.16 no.3
• /
• pp.183-187
• /
• 2006

We present the effects of rapid thermal annealing (RTA) temperature on the structural and optical properties of self-assembled InAs quantum dot (QD) structures grown on GaAs substrates by molecular beam epitaxy (MBE). The photoluminescence (PL) measurements are performed in a closed-cycle refrigerator as a function of temperature for the unannealed and annealed samples. RTA at higher temperature results in the increase in island size, the corresponding decrease in the density of islands, and the redshift in the PL emission from the islands. The temperature dependence of the PL peak energy for the InAs QDs is well expressed by the Varshni equation. The thermal quenching activation energies for the samples unannealed and annealed at $600^{\circ}C$ are found to be $25{\pm}5meV$ and $47{\pm}5$ meV, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.3
• /
• pp.115-120
• /
• 2023

ZnO/Cu/ZnO (ZCZ) thin film deposited on the glass substrate with DC and RF magnetron sputtering was rapid thermal annealed (RTA) and then effect of thermal temperature on the opto-electical and transparent heater properties of the films were considered. The visible transmittance and electrical resistivity are depends on the annealing temperature. The electrical resistivity decreased from 1.68 × 10^-3 Ωcm to 1.18 × 10^-3 Ωcm and the films annealed at 400℃ show a higher transmittance of 78.5%. In a heat radiation test, when a bias voltage of 20 V is applied to the ZCZ film annealed at 400℃, its steady state temperature is about 70.7℃. In a repetition test, the steady state temperature is reached within 15s for all of the bias voltages.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.446-447
• /
• 2007

The rapid thermal annealing effect of transparent IZTO(indium zinc oxide) and IAZO(indium alminium zinc oxide) films grown on glass substrate for solar cell or flat panel displays(FPDs) was studied. We prepared IZTO using RF magnetron sputtering and IAZO using DC co-sputtering method. Subsequently, using rapid thermal annealing(RTA) system, prepared IZTO and IAZO films were annealed at 300, 400, 500, $600^{\circ}C$ for 90sec. In addition, Electrical and optical characteristics were measured by Hall effect measurement and UV/Vis spectrometer examinations, respectively. To analyze structural properties and surface smoothness of the IZTO and IAZO films, XRD and SEM examinations were performed, respectively. It was shown that IZTO and IAZO films exhibited microcrystalline structure over $400^{\circ}C$ and amorphous structural regardless of RTA temperature, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.709-712
• /
• 2001

The effects of post annealing temperature by the Rapid Thermal Annealing(RTA) on the electrical properties of Pb(Zr,Ti)O$_3$(PZT) thin film were investigated. Analyses by the RTA treatments reveled that the leakage current of PZT thin films strongly depend on heating temperature and time. It was found that leakage current properties of PZT capacitor were changed by heating temperature during the RTA annealing. On Pt/Ti/Si substrates, PZT films are deposited at 350 $^{\circ}C$ by rf magnetron sputtering. The X-ray diffusion (XRD) was confirmed the formation of PZT thin film. Leakage current characteristics were improved with decreasing the post annealing temperature of PZT thin film. RTA annealed film on the 700$^{\circ}C$ shows ferroelectric and electrical properties with a remanent polarization of 12.4${\mu}$C/$\textrm{cm}^2$ coercive field of 117kV/cm, leakage current J= 6.2${\times}$10$\^$-6/ A/$\textrm{cm}^2$

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.321-326
• /
• 2013

The effect of rapid thermal annealing (RTA) on the optical properties of digital-alloy InGaAlAs multiple quantum well (MQW) structures have been investigated by using photoluminescence (PL) and time-resolved PL measurements as a function of RTA temperature. The MQW samples were annealed from $700^{\circ}C$ to $850^{\circ}C$ for 30 s in a nitrogen atmosphere. The MQW sample annealed at $750^{\circ}C$ exhibited the strongest PL intensity and the narrowest FWHM (Full width at half maximum), indicating the reduced nonradiative recombination centers and the improved interfaces between the wells and barriers. The MQW samples annealed at $800^{\circ}C$ and $850^{\circ}C$ showed the decreased PL intensities and blueshifted PL peaks compared to $750^{\circ}C$-annealed sample. The blueshift of PL peak with increasing RTA temperatures are ascribed to the increase of aluminum due to intermixing of gallium (Ga) and aluminum (Al) in the interfaces of InGaAs/InAlAs short-period superlattices. The decrease of PL intensity after annealing at $800^{\circ}C$ and $850^{\circ}C$ are attributed to the interface roughening and lateral composition modulation caused by the interdiffusion of Ga and Al and indium segregation, respectively. With increasing RTA temperature the PL decay becomes slower, indicating the decrease of nonradiative defect centers. The optical properties of digital-alloy InGaAlAs MQW structures can be improved significantly with optimum RTA conditions.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.02a
• /
• pp.525-526
• /
• 2009

we investigated the effect of rapid thermal annealing (RTA) temperature on photoluminescence (PL) of 635 nm InGaP/InGaAlP multiple quantum well structure. RTA is performed with the quantum well structure with 5.5 nm of well width. The highest PL peak intensity is shown at 1 min. of RTA at $720^{\circ}C$ sample as 3 times higher as compared to the as-grown sample. The effect may be assigned to an expected reduction in number of nonradiative recombination centers in the quantum well.