• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.80-81
• /
• 2008

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method. The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than $10^5$. Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권5호
• /
• pp.237-241
• /
• 2004

Amorphous silicon (a-Si) films are used in a broad range of solar cell, flat panel display, and sensor. Because of the greater ease of deposition and lower processing temperature, thin films are widely used for thin film transistors (TFTs). However, they have lower stability under the exposure of visible light and because of their low field effect mobility ($\mu$$_{FE}$ ) , less than 1 c $m^2$/Vs, they require a driving IC in the external circuits. On the other hand, polycrystalline silicon (poly-Si) thin films have superiority in $\mu$$_{FE}$ and optical stability in comparison to a-Si film. Many researches have been done to obtain high performance poly-Si because conventional methods such as excimer laser annealing, solid phase crystallization and metal induced crystallization have several difficulties to crystallize. In this paper, a new crystallization process using a molybdenum substrate has been proposed. As we use a flexible substrate, high temperature treatment and roll-to-roll process are possible. We have used a high temperature process above 75$0^{\circ}C$ to obtain poly-Si films on molybdenum substrates by a rapid thermal annealing (RTA) of the amorphous silicon (a-Si) layers. The properties of high temperature crystallized poly-Si studied, and poly-Si has been used for the fabrication of TFT. By this method, we are able to achieve high crystal volume fraction as well as high field effect mobility.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.101-104
• /
• 2018

An electric field was applied to a Mo conductive layer in the sandwiched structure of $glass/SiO_2/Mo/SiO_2/a-Si$ to induce Joule heating in order to generate the intense heat needed to carry out the crystallization of amorphous silicon. Polycrystalline silicon was produced via Joule heating through a solid state transformation. Blanket crystallization was accomplished within the range of millisecond, thus demonstrating the possibility of a new crystallization route for amorphous silicon films. The grain size of JIC poly-Si can be varied from few tens of nanometers to the one having the larger grain size exceeding that of excimer laser crystallized (ELC) poly-Si according to transmission electron microscopy. We report here the blanket crystallization of amorphous silicon films using the $2^{nd}$ generation glass substrate.

• 융합정보논문지
• /
• 제9권3호
• /
• pp.75-81
• /
• 2019

본 논문은 유기물로 이루어진 폴리머 기판상에 저온 다결정 실리콘 박막트랜지스터 제조방법에 대해 연구하였다. 먼저, 폴리머 기판에 화학증착방식으로 비결정 실리콘 박막을 증착하였고, 열처리 장치인 퍼니스로 탈수소 및 활성화 공정을 430도에서 2시간동안 진행하였다. 이후 엑시머 레이저를 이용하여 결정화를 진행하여 다결정 실리콘 반도체 막을 제조하였다. 이 박막은 박막트랜지스터 제작을 위한 활성층으로 사용하였다. 제작된 p형 박막트랜지스터는 이동도 $77cm^2/V{\cdot}s$, on/off 전류비는 $10^7$이상의 동작특성을 보였고, 이는 결정화된 박막내부에 결함 농도가 낮음을 의미한다. 이 결과로 유기물 기판상에 엑시머 레이저로 형성된 다결정 실리콘으로 제작된 전자소자는 플렉서블 AMOLED 디스플레이 회로 형성에 최적의 기술임을 알 수 있다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.305-308
• /
• 2004

We present a novel process for the ultra low temperature (<150$^{\circ}C$) polycrystalline silicon (ULTPS) TFT for the flexible display applications on the plastic substrate. The sequential lateral solidification (SLS) was used for the crystallization of the amorphous silicon film deposited by rf magnetron sputtering, resulting in high mobility polycrystalline silicon (poly-Si) film. The gate dielectric was composed of thin $SiO_2$ formed by plasma oxidation and $Al_2O_3$ deposited by plasma enhanced atomic layer deposition. The breakdown field of gate dielectric on poly-Si film showed above 6.3 MV/cm. Laser activation reduced the source/drain resistance below 200 ${\Omega}$/ㅁ for n layer and 400 ${\Omega}$/ㅁ for p layer. The fabricated ULTPS TFT shows excellent performance with mobilities of 114 $cm^2$/Vs (nMOS) and 42 $cm^2$/Vs (pMOS), on/off current ratios of 4.20${\times}10^6$ (nMOS) and 5.7${\times}10^5$ (PMOS).

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권5호
• /
• pp.339-343
• /
• 1999

This paper reports the characteristics of poly-Si TFT unitary CMOS circuits fabricated with various techniques, in order to investigate the optimum process conditions. The active films were deposited by PECVD and LPCVD using $SiH_4\; and\; Si_2H_6$ as source gas, and annealed by SPC and ELA methods. The impurity doping of the oource and drain electrodes was performed by ion implantation and ion shower. In order to investigate the AC characteristics of the poly-Si TFTs processed with various methods, we have examined the current driving characteristics of the polt-Si TFT and the frequency characteristics of 23-stage CMOS ring oscillators. Ithas been observed that the circuits fabricated using $Si_2H_6$ with low-temperature process of ELA exhibit high switching speed and current driving performances, thus suitable for real application of large area electronics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.323-327
• /
• 2006

We present the most recent experimental results on Thin-beam Directional X'tallization (TDX), a rapid excimer-laser-based crystallization method for creating extremely high-quality large-grained polycrystalline silicon films on glass substrates. We will present experimental data obtained with our prototype Gen 2 tool, and discuss the ability to produce different types of poly-Si material.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.445-446
• /
• 2005

This letter reports the fabrication of polycrystalline silicon thin-film transistors (poly-Si TFT) on flexible plastic substrates using amorphous silicon (a-Si) precursor films by sputter deposition. The a-Si films were deposited with mixture gas of argon and helium to minimize the argon incorporation into the film. The precursor films were then laser crystallized using XeCl excimer laser irradiation and a four-mask-processed poly-Si TFTs were fabricated with fully self-aligned top gate structure.

• 한국표면공학회지
• /
• 제47권1호
• /
• pp.20-24
• /
• 2014

Joule heat is generated by applying an electric filed to a conductive layer located beneath or above the amorphous silicon film, and is used to raise the temperature of the silicon film to crystallization temperature. An electric field was applied to an indium tin oxide (ITO) conductive layer to induce Joule heating in order to carry out the crystallization of amorphous silicon. Polycrystalline silicon was produced within the range of a millisecond. To investigate the kinetics of Joule-heating induced crystallization (JIC) solid phase crystallization was conducted using amorphous silicon films deposited by plasma enhanced chemical vapor deposition and using tube furnace in nitrogen ambient. Microscopic and macroscopic uniformity of crystallinity of JIC poly-Si was measured to have better uniformity compared to that of poly-Si produced by other methods such as metal induced crystallization and Excimer laser crystallization.

• 마이크로전자및패키징학회지
• /
• 제13권4호
• /
• pp.27-36
• /
• 2006

약 10%이하의 Pt 또는 Ir 첨가시켜 니켈모노실리싸이드를 고온에서 안정화 시키는 것이 가능한지 확인하기 위해서 활성화영역을 가정한 단결정 실리콘 웨이퍼와 게이트를 상정한 폴리 실리콘 웨이퍼 전면에 Ni, Pt, Ir을 열증착기로 성막하여 10 nm-Ni/l nm-Pt/(poly)Si, 10 nm-Ni/l nm-Ir/(poly)Si 구조를 만들었다. 준비된 시편을 쾌속 열처리기를 이용하여 40초간 실리사이드화 열처리 온도를 $300^{\circ}C{\sim}1200^{\circ}C$ 범위에서 변화시켜 두께 50nm의 실리사이드를 완성하였다. 완성된 Pt와 Ir이 첨가된 니켈실리사이드의 온도별 전기저항변화, 두께변화, 표면조도변화, 상변화, 성분변화를 각각 사점전기저항측정기와 광발산주사전자현미경, 주사탐침현미경, XRD와 Auger depth profiling으로 각각 확인하였다. Pt를 첨가한 결과 기판 종류에 관계없이 기존의 니켈실리사이드 공정에 의한 NiSi와 비교하여 $700^{\circ}C$ 이상의 NiSi 안정화 구역을 넓히는 효과는 없었고 면저항이 커지는 문제가 있었다. Ir을 삽입한 경우는 단결정 실리콘 기판에서는 $500^{\circ}C$ 이상에서의 NiSi와 동일하게 $1200^{\circ}C$까지 안정한 저저항을 보여서 Ir이 효과적으로 Ni(Ir)Si 형태로 $NiSi_{2}$로의 상변태를 적극적으로 억제하는 특성을 보이고 있었고, 다결정 기판에서는 $850^{\circ}C$까지 효과적으로 NiSi의 고온 안정성을 향상시킬 수 있었다.