• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.288-290
• /
• 2014

In this paper, Escape and BTA(Bus Turn Around) modes of master bridge IC are implemented, which supports MIPI(Mobile Industry Processor Interface) DSI(Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module(slave) in order to test it. The Escape mode is designed to implement LPDT, ULPS and trigger message transmissions. The BTA mode is designed to obtain various status information from slave in reverse direction. Functional simulation results show that the designed Escape and BTA modes work correctly for various conditions defined in MIPI DSI standard.

• The Journal of the Korea Contents Association
• /
• v.10 no.12
• /
• pp.10-17
• /
• 2010

In this paper, we design digital D-PHY link chip controling DSI (Display Serial Interface) that meets MIPI (Mobile Industry Processor Interface) standard. The D-PHY supports a high-speed (HS) mode for fast data traffic and a low-power (LP) mode for control transactions. For low power consumption, the unit blocks in digital D-PHY are optionally switched using the clock gating technique. The proposed low power digital D-PHY is simulated and compared with conven tional one about power consumption on each transaction mode. As a result, power consumptions of TX, RX, and total in HS mode decrease 74%, 31%, and 50%, respectively. In LP mode, power reduction rates of TX, RX, and total are 79%, 40%, and 51.5%, separately. We implemented the low power MIPI D-PHY digital chip using $0.13-{\mu}m$ CMOS process under 1.2V supply.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2014.10a
• /
• pp.291-292
• /
• 2014

High-speed video transmission modes of master bridge IC are implemented, which supports MIPI (Mobile Industry Processor Interface) DSI (Display Serial Interface) standard. MIPI DSI master bridge IC sends RGB data and various commands to display module (slave) in order to test it. The master bridge IC consists of buffers storing video data of two lines, packet generation block, and D-PHY layer that distributes packets to data lanes and transmits them to slave. In addition, it supports four bpp (bit per pixel) formats and three transmission modes including Burst and Non-Burst (Sync Events, Sync Pulses types). The designed bridge IC is verified by RTL simulations showing that it functions correctly for various operating parameters.

• Journal of IKEEE
• /
• v.23 no.4
• /
• pp.1257-1264
• /
• 2019

A 3-GSymbol/s/lane transceiver, which supports the mobile industry processor interface (MIPI) C-physical layer (PHY) specification version 1.1, is proposed. It performs channel mismatch correction to improve the signal integrity that is deteriorated by using three-level signals over three channels. The proposed channel mismatch correction is performed by detecting channel mismatches in the receiver and adjusting the delay times of the transmission data in the transmitter according to the detection result. The channel mismatch detection in the receiver is performed by comparing the phases of the received signals with respect to the pre-determined data pattern transmitted from the transmitter. The proposed MIPI C-PHY receiver is designed using a 65 nm complementary metal-oxide-semiconductor (CMOS) process with 1.2 V supply voltage. The area and power consumption of each transceiver lane are 0.136 ㎟ and 17.4 mW/GSymbol/s, respectively. The proposed channel mismatch correction reduces the time jitter of 88.6 ps caused by the channel mismatch to 34.9 ps.

• The KIPS Transactions:PartA
• /
• v.14A no.7
• /
• pp.391-398
• /
• 2007

In this paper, we design a future mobile camera standard interface based on the MIPI CSI-2 and D-PHY specification. The proposed CSI-2 have the efficient multi-lane management layer, which the independent buffer on the each lane are merged into single buffer. This scheme can flexibly manage data on multi lanes though the number of supported lanes are mismatched in a camera processor transmitter and a host processor. The proposed CSI-2 & D-PHY are verified under test bench. We make an experiment on CSI-2 & D-PHY with FPGA type test-bed and implement them onto a mobile handset. The proposed CSI-2 & D-PHY module are used as both the bridge type and the future camera processor IP for SoC.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.4
• /
• pp.506-517
• /
• 2015

This paper presents a 1.248 Gb/s - 2.918 Gb/s low-power receiver MIPI-DigRF M-PHY with a fully digital frequency detection loop. MIPI-DigRF M-PHY should be operated in a very short training time which is $0.01{\mu}s$ the for HS-G2B mode. Because of this short SYNC pattern, clock and data recovery (CDR) should have extremely fast locking time. Thus, the quarter rate CDR with a fully digital frequency detection loop is proposed to implement a fast phase tracking loop. Also, a low power CDR architecture, deserializer and voltage controlled oscillator (VCO) are proposed to meet the low power requirement of MIPI-DigRF M-PHY. This chip is fabricated using a $0.11{\mu}m$ CMOS process, and the die area is $600{\mu}m{\times}250{\mu}m$. The power consumption of the receiver is 16 mW from the supply voltage of 1.1 V. The measured lock time of the CDR is less than 20 ns. The measured rms and peak jitter are $35.24ps_{p-p}$ and $4.25ps_{rms}$ respectively for HS-G2 mode.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.899-905
• /
• 2017

This paper presents a reference-less dual loop clock and data recovery (CDR) circuit that supports a data rate of 2.496 Gb/s for the mobile industry processor interface (MIPI) M-PHY. An adaptive loop bandwidth scheme is used to implement the fast lock time maintaining a low time jitter. To this scheme, the proposed CDR consists of two loops for a frequency locked loop and a phase locked loop. The proposed 2.496 Gb/s reference-less dual loop CDR is designed using a 65 nm CMOS process with 1.2 V supply voltage. The simulated peak-to-peak jitter of output clock is 9.26 ps for the input data of 2.496 Gb/s pseudo-random binary sequence (PRBS) 15. The active area and power consumption of the implemented CDR are $470{\times}400{\mu}m^2$ and 6.49 mW, respectively.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.2
• /
• pp.67-72
• /
• 2015

For the development of UFS device test system, M-PHY specifications should be matched with MIPI-standard which is analog signal protocol. In this paper, the implementation methodology and hardware structure for the M-PHY AFE (Analog Front End) Block was suggested that it can be implemented using universal components without ASIC process. The testing procedure has a jitter problem so to solve the problems we using ASIC process, normally but the ASIC process needs a lot of developing cost making the UFS device test system. In is paper, the suggestion was verified by the output signal which was compared to the MIPI-standard on the Prototype-board using universal components. The board was reduced the jitter on the condition of HS-TX and 5.824 Gbps Mode in SerDes (Serialize-deserializer). Finally, the suggestion and developed AFE block have a useful better than ASIC process on developing costs of the industrial UFS device test system.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.62-70
• /
• 2007

In this paper, we design a mobile camera processor to support the MIPI CSI-2 and DPHY specification. The lane management sub-layer of CIS2 handles multi-lane configuration. Thus conceptually, the transmitter and receiver have each independent buffer on multi lanes. In the proposed architecture, the independent buffers are merged into a single common buffer. The single buffer architecture can flexibly manage data on multi lanes though the number of supported lanes are mismatched in a camera processor transmitter and a host processor. For a key issue for the data synchronization problem, the synchronization start codes are added as the starting for image data. We design synchronization logic to synchronize the received clock and to generate the byte clock. We present the verification results under proposed test bench. And we show the waves of simulation and logic synthesis results of the designed processor.

• BMB Reports
• /
• v.41 no.9
• /
• pp.678-683
• /
• 2008

The initial step during assembly of the hepatitis A virus particle is driven by domain 2A of P1-2A, which is the precursor of the structural proteins. The proteolytic removal of 2A from particulate VP1-2A by an as yet unknown host enzyme presumably terminates viral morphogenesis. Using a genetic approach, we show that a basic amino acid residue at the C-terminus of VP1 is required for efficient particle assembly and that host proteases trypsin and cathepsin L remove 2A from hepatitis A virus particles in vitro. Analyses of insertion mutants in the C-terminus of 2A reveal that this part of 2A is important for liberation of P1-2A from the polyprotein. The data provide the first evidence that the VP1/2A junction is involved in both viral particle assembly and maturation and, therefore, seems to coordinate the first and last steps in viral morphogenesis.