• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.2
• /
• pp.160-164
• /
• 2010

The radio frequency (RF) model of SOI FinFETs with gate length of 40 nm is verified by using a 3-dimensional (3-D) device simulator. This paper shows the equivalent circuit model which can be used in the circuit analysis simulator. The RMS modeling error of Y-parameter was calculated to be only 0.3 %.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.2
• /
• pp.191-197
• /
• 2016

In this paper, we investigated the hotcarrier injection (HCI) mechanism, one of the most important reliability issues, in 10 nm node Input/Output (I/O) bulk FinFET. The FinFET has much intensive HCI damage in Fin-bottom region, while the HCI damage for planar device has relatively uniform behavior. The local damage behavior in the FinFET is due to the geometrical characteristics. Also, the HCI is significantly affected by doping profile, which could change the worst HCI bias condition. This work suggested comprehensive understanding of HCI mechanisms and the guideline of doping profile in 10 nm node I/O bulk FinFET.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.1
• /
• pp.10-16
• /
• 2016

In this paper, a design for a fully digital voltage sensor using a 32-nm fin-type field-effect transistor (FinFET) is presented. A new characteristic of the double gate p-type FinFET (p-FinFET) is examined and proven appropriate for sensing voltage variations. On the basis of this characteristic, a novel technique for designing low-power voltage-to-time converters is presented. Then, we develop a digital voltage sensor with a voltage range of 0.7 to 1.1V at a 50-mV resolution. The performance of the proposed sensor is evaluated under a range of voltages and process variations using Simulation Program with Integrated Circuit Emphasis (SPICE) simulations, and the sensor is proven capable of operating under ultra-low power consumption, high linearity, and fairly high-frequency conditions (i.e., 100 MHz).

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.266-272
• /
• 2009

In the present work three dimensional process and device simulations were employed to study the performance variations with RTA. It is observed that with the increase in RTA temperature, the arsenic dopants from the source /drain region diffuse laterally under the spacer region and simultaneously acceptors (Boron) are redistributed from the central axis region of the fin towards the Si/SiO2 interface. As a consequence both drive current and peak cut-off frequency of an n-FinFET are observed to improve with RTA temperatures. Volume inversion and hence the flow of carries through the central axis region of the fin due to reduced scattering was found behind the performance improvements with increasing RTA temperature.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.554-562
• /
• 2015

This paper presents the design and analysis of gate-recessed AlGaN/GaN Fin-type Field-Effect Transistor (FinFET). The three-dimensional (3-D) technology computer-aided design (TCAD) simulations were performed to analyze the direct-current (DC) and radio-frequency (RF) characteristics for AlGaN/GaN FinFETs. The fin width ($W_{fin}$) and the height of GaN layer ($H_{GaN}$) are the design parameters used to improve the electrical performances of gate-recessed AlGaN/GaN FinFET.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.8 no.2
• /
• pp.156-163
• /
• 2008

We proposed a new $p^+/n^+$ gate locally-separated-channel (LSC) bulk FinFET which has vertically formed oxide region in the center of fin body, and device characteristics were optimized and compared with that of normal channel (NC) FinFET. Key device characteristics were investigated by changing length of $n^+$ poly-Si gate ($L_s$), the material filling the trench, and the width and length of the trench at a given gate length ($L_g$). Using 3-dimensional simulations, we confirmed that short-channel effects were properly suppressed although the fin width was the same as that of NC device. The LSC device having the trench non-overlapped with the source/drain diffusion region showed excellent $I_{off}$ suitable for sub-50 nm DRAM cell transistors. Design of the LSC devices were performed to get reasonable $L_s/L_g$ and channel fin width ($W_{cfin}$) at given $L_gs$ of 30 nm, 40 nm, and 50 nm.

• Electronics and Telecommunications Trends
• /
• v.38 no.6
• /
• pp.52-61
• /
• 2023

With semiconductor scaling approaching the physical limits, devices including CMOS (complementary metal-oxide-semiconductor) components have managed to overcome yet are currently struggling with several technical issues like short-channel effects. Evolving from the process node of 22 nm with FinFET (fin field effect transistor), state-of-the-art semiconductor technology has reached the 3 nm node with the GAA-FET (gate-all-around FET), which appropriately addresses the main issues of power, performance, and cost. Technical problems remain regarding the foundry of GAA-FET, and next-generation devices called post-GAA transistors have not yet been devised, except for the CFET (complementary FET). We introduce a CFET that spatially stacks p- and n-channel FETs on the same footprint and describe its structure and fabrication. Technical details like stacking of nanosheets, special spacers, hetero-epitaxy, and selective recess are more thoroughly reviewed than in similar articles on CFET fabrication.

• Electronics and Telecommunications Trends
• /
• v.38 no.1
• /
• pp.36-45
• /
• 2023

The increasing demand for ultra-high efficiency of compact power conversion systems for electric vehicle applications has brought GaN power semiconductors to the fore due to their low conduction losses and fast switching speed. In particular, the development of materials and core device processes contributed to remarkable results regarding the publication of vertical GaN power devices with high breakdown voltage. This paper reviews recent advances on GaN material technology and vertical GaN power device technology. The GaN material technology covers the latest technological trends and GaN epitaxial growth technology, while the vertical GaN power device technology examines diodes, Trench FETs, JFETs, and FinFETs and reviews the vertical GaN PiN diode technology developed by ETRI.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.3
• /
• pp.156-161
• /
• 2015

In this paper, we present simulation results obtained using SILVACO TCAD tools for a 3-D silicon on insulator (SOI) n-FinFET structure with a gate length of 8 nm at 300K. The effects of variations of the device’s key electrical parameters, such as threshold voltage, subthreshold slope, transconductance, drain induced barrier lowering, oncurrent, leakage current and on/off current ratio are presented and analyzed. We will also describe some simulation results related to the influence of the gate work function variations on the considered structure. These variations have a direct impact on the electrical device characteristics. The results show that the threshold voltage decreases when we reduce the gate metal work function Φ_m. As a consequence, the behavior of the leakage current improves with increased Φ_m. Therefore, the short channel effects in real 3-D FinFET structures can reasonably be controlled and improved by proper adjustment of the gate metal work function.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.10 no.4
• /
• pp.265-275
• /
• 2010

In this work, reliable methodology for device design is presented. Based on this method, the underlap length has been optimized for minimizing the gateinduced drain leakage (GIDL) in a 22-nm node 4-terminal (4-T) silicon-on-insulator (SOI) fin-shaped field effect transistor (FinFET) by TCAD simulation. In order to examine the effects of underlap length on GIDL more realistically, doping profile of the source and drain (S/D) junctions, carrier lifetimes, and the parameters for a band-to-band tunneling (BTBT) model have been experimentally extracted from the devices of 90-nm channel length as well as pnjunction test element groups (TEGs). It was confirmed that the underlap length should be near 15 nm to suppress GIDL effectively for reliable low standby power (LSTP) operation.