• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.168-172
• /
• 2003

This paper analyzes the output noise and the noise figure of common source MOSFET pair each input of which is separately driven in the different frequencies. This analysis is performed for concurrent dual band cascode CMOS LNA with double inputs and single output fabricated in $0.18{\mu}m$ CMOS process. Since both inputs and output are matched to near $50{\Omega}$ using on-chip inductors, the measured noise figures are much higher than those of usual CMOS LNA. But, the main concern of this paper is focused on the added noise features due to the other channel common source stage. The dual-band LNA results in noise figure of 4.54dB at 2.14GHz and 6.03dB at 5.25GHz for selectable operation and 7.44dB and 6.58dB for concurrent operation. The noise analysis explains why the added noise at each band shows so large difference.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.321-328
• /
• 2008

In this paper, variable gain amplifier(VGA) with a gain slope controller has been proposed and verified by circuit simulations and measurements. The proposed VGA has a gain control, gain slope switch and variable gain range. The input source coupled pair with diode connected load is used for VGA gain stage. The gain slope controller with switch can control VGA gain slope. The proposed VGA is fabricated in $0.18{\mu}m$ CMOS process for multi -standard wireless receiver. The proposed two stage VGA consumes min. 2.0 mW to max. 2.6 mW in gain control range and gives input IP3 of -3.77 dBm and NF of 28.7 dB at 1.8 V power supply under -25 dBm, 1 MHz input. The proposed VGA has 37 dB(-16 dB $\sim$ 21 dB) variable gain range, and 8 dB gain range control per 0.3 V control voltage, and can provide variable gain, positive and negative gain slope control, and gain range control. This VGA characteristics provide design flexibility in multi-standard wireless receiver.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.11
• /
• pp.18-26
• /
• 2011

This paper describes a multi-mode LDPC decoder which supports three block lengths(648, 1296, 1944) and four code rates(1/2, 2/3, 3/4, 5/6) of IEEE 802.11n wireless LAN standard. To minimize hardware complexity, it adopts a block-serial (partially parallel) architecture based on the layered decoding scheme. A novel memory reduction technique devised using the min-sum decoding algorithm reduces the size of check-node memory by 47% as compared to conventional method. From fixed-point modeling and Matlab simulations for various bit-widths, decoding performance and optimal hardware parameters such as fixed-point bit-width are analyzed. The designed LDPC decoder is verified by FPGA implementation, and synthesized with a 0.18-${\mu}m$ CMOS cell library. It has 219,100 gates and 45,036 bits RAM, and the estimated throughput is about 164~212 Mbps at 50 MHz@2.5v.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.15-22
• /
• 2006

In this paper, 1.8V 8-bit 500MSPS Low-power CMOS Digital-to-Analog Converter(DAC) for UWB(Ultra Wide Band) Communication Systeme is proposed. The architecture of the DAC is based on a current steering 6+2 full matrix type which has low glitch and high linearity. In order to achieve a high speed and good performance, a current cell with a high output impedance and wide swing output range is designed. Further a thermometer decoder with same delay time and low-power switching decoder for high efficiency performance are proposed. The proposed DAC was implemented with TSMC 0.18um 1-poly 6-metal N-well CMOS technology. The measured SFDR was 49dB when the output frequency was 50MHz at 500MS/s sampling frequency. The measured INL and DNL were 0.9LSB and 0.3LSB respectively. The DAC power dissipation was 20mW and the effective chip area was $0.63mm^2$.

• ETRI Journal
• /
• v.30 no.6
• /
• pp.850-852
• /
• 2008

This letter presents a power efficient 64-state Viterbi decoder (VD) employing a two-stage radix-4 add-compare-select architecture. A class of VD architectures is implemented, and their hardware complexity, maximum operating speed, and power consumption are compared. Implementation results show that the proposed VD architecture is suitable for multiband orthogonal frequency-division multiplexing (MB-OFDM) ultra-wideband (UWB) systems, which can support the data rate of 480 Mbps even when implemented using 0.18-${\mu}m$ CMOS technology.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.587-588
• /
• 2008

Digital PLL을 위한 높은 해상도를 갖는 TDC(Time to Digital Converter)를 $0.18{\mu}m$ CMOS 공정으로 설계하였다. 2단 구조를 갖는 TDC를 제안하였고 이를 Cadence Spectre를 이용하여 검증하였다. TDC는 Difference pulse generator, coarse 변환기와 fine 변환기로 구성된다. 그리고, 2단 변환기와 Thermometer decoder를 이용하여 delay cell의 수를 적게 유지하면서도 높은 해상도를 얻을 수 있었다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.6 s.336
• /
• pp.1-8
• /
• 2005

In this paper, CMOS A/D converter with 6bit 2GSPS Nyquist input at 1.8V is designed. In order to obtain the resolution of 6bit and the character of high-speed operation, we present an Interpolation type architecture. In order to overcome the problems of high speed operation, a novel One-zero Detecting Encoder, a circuit to reduce the Reference Fluctuation, an Averaging Resistor and a Track & Hold, a novel Buffered Reference for the improved SNR are proposed. The proposed ADC is based on 0.18um 1-poly 3-metal N-well CMOS technology, and it consumes 145mW at 1.8V power supply and occupies chip area of 977um $\times$ 1040um. Experimental result show that SNDR is 36.25 dB when sampling frequency is 2GHz and INL/DNL is $\pm$0.5LSB at static performance.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.1
• /
• pp.76-81
• /
• 2009

A novel design method of time-interleaved subranging ADC is presented. We use the bisection method to let only half of comparators in typical subranging ADC working in every clock cycle. Thus, we are able to reduce the number of comparators by half. It is possible to reduce the die size. An example of 8-bit time-interleaved subranging ADC operates at 40MHz sampling rate and 1.8V supply voltage is demonstrated. The power consumption of the proposed circuit is only 10mV with SPECTRE simulation. Compared with the typical subranging ADC, our bisection method is able to reduce up to 40% in die size.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.4
• /
• pp.192-197
• /
• 2009

This paper presents the design and measurement of a 2.4/5.2-GHz dual band VCO with a balanced frequency doubler in $0.18\;{\mu}m$ CMOS process. The topology of a 2.4 GHz VCO is a cross-coupled VCO with a LC tank and the frequency of the VCO is doubled by a frequency balanced doubler for a 5.2 GHz VCO. The gate bias matching network for class B operation in the balanced doubler is adopted to obtain as much power at 2nd harmonic output as possible. The average output powers of the 2.4 GHz and 5.2 GHz VCOs are -12 dBm and -13 dBm, respectively, the doubled VCO has fundamental harmonic suppression of -25 dB. The measured phase noises at 5 MHz frequency offset are -123 dBc /Hz from 2.6 GHz and -118 dBc /Hz from 5.1 GHz. The total size of the dual band VCO is $1.0\;mm{\times}0.9\;mm$ including pads.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.1
• /
• pp.54-61
• /
• 2008

This paper presents a new TIQ based CMOS flash 6-bit ADC to process digital signal in real time. In order to improve the conversion speed of ADC by designing new logic or layout of ADC circuits, a new design method is proposed in encoding logic circuits. The proposed encoding circuits convert analog input into digitally encoded double base number system(DBNS), which uses two bases unlike the normal binary representation scheme. The DBNS adopts binary and ternary radix to enhance digital arithmetic processing capability. In the DBNS, the addition and multiplication can be processed with just shift operations only. Finding near canonical representation is the most important work in general DBNS. But the main disadvantage of DBNS representation in ADC is the fan-in problem. Thus, an equal distribution algorithm is developed to solve the fan-in problem after assignment the prime numbers first. The conversion speed of simulation result was 1.6 GSPS, at 1.8V power with the Magna $0.18{\mu}m$ CMOS process, and the maximum power consumption was 38.71mW.