• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.8
• /
• pp.966-974
• /
• 2019

In this study, we propose a CMOS power amplifier (PA) using a bypass technique to enhance the efficiency in the low-power region. For the bypass structure, the common-gate (CG) transistor of the cascode structure of the driver stage is divided in two parallel branches. One of the CG transistors is designed to drive the power stage for high-power mode. The other CG transistor is designed to bypass the power stage for low-power mode. Owing to a turning-off of the power stage, the power consumption is decreased in low-power mode. The measured maximum output power is 20.35 dBm with a power added efficiency of 12.10%. At a measured output power of 11.52 dBm, the PAE is improved from 1.90% to 7.00% by bypassing the power stage. Based on the measurement results, we verified the functionality of the proposed bypass structure.

• Proceedings of the Korean Information Science Society Conference
• /
• 2004.04a
• /
• pp.526-528
• /
• 2004

본 논문은 유무선 환경에서 TCP를 이용한 데이터 전송 시 에이젼트를 이용하여 패킷 손실의 원인을 분석, 무선 링크에서 발생한 패킷 손실에 대해서는 혼잡 윈도우 크기를 유지하고, 유선 링크에서 발생한 패킷 손실에 대해서는 지역 재전송을 수행하는 저 전력 전송기법을 제안한다. 제안하는 저 전력 전송기법은 전송 후 WNIC를 저 전력 모드로 전환시킴으로써 WNIC 전력소비를 최소화한다. NS2 시뮬레이션 결과 기존 TCP 보다 무선 링크에서 에러 발생시 67~177(%) 성능향상과 22~44(%) 에너지 감소효과를 보였고, 유선 링크에서 에러 발생시 3~22(%)의 성능 향상과 2~13(%) 에너지 감소 효과를 나타냈다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.2
• /
• pp.159-164
• /
• 2016

A wireless communication system is required to be implemented with the low power circuits because it uses a battery having a limited energy. Therefore, the current mode circuit has been studied because it consumes constant power regardless of the frequency change. However, the clock-feedthrough problem is happened by leak of stored energy in memory operation. In this paper, we suggest the current memory circuit to minimize the clock-feedthrough problem and introduce a technique for ultra low power operation by inducing dynamic voltage scaling. The current memory circuit was designed with BSIM3 model of $0.35{\mu}m$ process and was operated in the near-threshold region. From the simulation result, the clock-feedthrough could be minimized when designing the memory MOS Width of $2{\mu}m$, the switch MOS Width of $0.3{\mu}m$ and dummy MOS Width of $13{\mu}m$ in 1MHz switching operation. The power consumption was calculated with $3.7{\mu}W$ at the supply voltage of 1.2 V, near-threshold voltage.

• Journal of Advanced Navigation Technology
• /
• v.14 no.2
• /
• pp.220-226
• /
• 2010

In this paper, an low power symbol detector is proposed for MIMO communication system with two transmit and two receive antennas. The proposed symbol detector can support both the spatial multiplexing (SM) mode and spatial diversity (SD) mode for MIMO transmission technique, and shows the optimal maximum likelihood (ML) performance. Also, by sharing the hardware block and using the dedicated clock MIMO modes, the power of the proposed architecture is dramatically decreased. The proposed symbol detector was designed in hardware description language (HDL) and synthesized to logic gates using a $0.13-{\mu}m$ CMOS standard cell library. The power consumption was estimated by using Synopsys Power CompilerTM, which is reduced by maximum 85%, compared with the conventional architecture.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2002.04a
• /
• pp.635-638
• /
• 2002

BIST(Built-In Self-Test)를 이용한 테스트 방식은 정상 동작 모드인 회로에 비해 테스트 모드에서 보다 많은 스위칭이 발생하고, 과도한 전력 소모에 의해 회로가 손상을 받을 수 있는 문제점을 갖고 있다. 본 논문은 test-per-clock BIST 구조에서 전력이 제한되어 있을 때 테스트 적용 시간과 총 에너지 소비를 최소화하기 위한 테스트 스케줄링 알고리즘을 제안한다. 제안된 방법은 테스트 세션을 구성함에 있어 각 세션에 포함되는 각 블록의 테스트 시작 시간을 동적으로 결정하여 기존의 알고리즘에 비하여 전력 소모와 전체 테스트 시간을 줄일 수 있다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.3
• /
• pp.486-495
• /
• 2006

In this paper, a low-power 1Kb synchronous EEPROM is designed with flash cells for passive UHF RFID tag chips. To make a low-power EEPROM, four techniques are newly proposed. Firstly, dual power supply voltages VDD(1.5V) and VDDP(2.5V), are used. Secondly, CKE signal is used to remove switching current due to clocking of synchronous circuits. Thirdly, a low-speed but low-power sensing scheme using clocked inverters is used instead of the conventional current sensing method. Lastly, the low-voltage, VDD for the reference voltage generator is supplied by using the Voltage-up converter in write cycle. An EEPROM is fabricated with the $0.25{\mu}m$ EEPROM process. Simulation results show that power dissipations are $4.25{\mu}W$ in the read cycle and $25{\mu}W$ in the write cycle, respectively. The layout area is $646.3\times657.68{\mu}m^2$.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.5
• /
• pp.983-989
• /
• 2012

IEEE 802.3az LPI mechanism allows an Ethernet link to reduce power consumption by entering a low-power sleeping mode and letting some components being powered off when there is no data to be transmitted through the link. However, if small amount of packets are being sent periodically, such a mechanism can not obtain energy efficiency due to a high overhead caused by excessive mode transitions. In this paper, we propose an enhanced LPI mechanism which can perform state transition adaptively based on the traffic characteristics on transport layer and network status. This simulation result shows that proposed mechanism improves energy efficiency than LPI mechanism with respect to energy consumption rate for various traffic loads.

• Journal of Broadcast Engineering
• /
• v.10 no.1 s.26
• /
• pp.77-82
• /
• 2005

We propose a highly Integrated motion estimation processor (MEP) for efficient video compression in an SoC platform. When compressing video by the standards like MPEG-4 and H.263, the macroblock related functions motion compensation. mode decision, motion vector prediction, and motion vector difference calculation require the frequent intervention of MCU. Thus the proposed MEP incorporates those functions with the motion estimation capability to reduce the number of interrupts to MCU, which can lead to a highly efficient SoC system. For low-power consumption, the proposed MEP can prevent the temporally static area from motion estimation or can skip the half-pel motion estimation for those macroblocks whose modes are decided as INTRA.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.6
• /
• pp.1-9
• /
• 2010

In this paper, we propose a hi-speed/low-power Extended QRD-RLS(QR-Decomposition Recursive Least Squares) equalizer with systolic array structure. In the conventional systolic array structure, vector mode CORDIC on the boundary cell calculates angle of input vector, and the rotation mode CORDIC on the internal cell rotates vector. But, in the proposed structure, it is shown that implementation complexity can be reduced using the rotation direction of vector mode CORDIC and rotation mode CORDIC. Furthermore, calculation time can be reduced by 1/2 since vector mode and rotation mode CORDIC operate at the same time. Through HDL coding and chip implementation, it is shown that implementation area is reduced by 23.8% compared with one of conventional structure.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.5
• /
• pp.61-70
• /
• 2004

The operation mode of neural network is divided into learning and recognition process. Learning is updating process of weight until neural network archives target result from input pattern. Recognition is arithmetic process of input pattern and weight. Traditional inner product process is focused to improve processing speed and hardware complexity. There is no hardware architecture to distinguish between loaming and recognition mode of neural network. In this paper we propose the new architecture of low power inner product processor for reconfigurable neural network. The proposed architecture is similar with bit-serial inner product processor on learning mode. It have several advantages which are fast processing base on bit-level, suitability of hardware implementation and pipeline architecture to compute data. And proposed architecture minimizes active units and reduces consumption power on recognition mode. Result of simulation shows that active units is depend on bit representation of weight, but we can reduce active units about 50 precent.