Proceedings of the Korean Society for Technology of Plasticity Conference (한국소성가공학회:학술대회논문집)
The Korean Society for Technology of Plasticity and materials processing
- Semi Annual
Domain
- Materials > Plastic Deformation Process/Powders
1998.03a
-
An analysis for the prediction of wrinkling formation in curved sheets during metal froming is presented. We construct "Wrinkling Limit diagram"(WLD) which represent the combinations of the critical principal stresses for wrinkling formation in curved sheet elements subjected to biaxial plane stress. Here the scheme of plastic bifurcation theory for thin shells based on the Donnell-Mushtari-Vlasov shell theory is used. In this study, the effects of the material variables (yield stress, plastic hardening coefficient, plastic anisotropic parameter, and so on) and sheet geometry on the critical conditions for wrinkling is carried out numerically.merically.
-
Wrinkling is one of the major defects in sheet metal products and may be also attributable to the wear of the tool. The initiation and growth of the wrinkles are influenced by many factors such as stress state, mechanical properites of the sheet material, geometry of the body, and contact condition. It is difficult to analyze the wrinkling initiation and growth considering the factors because the effects of the factors are very complex and the wrinkling behavior may show wide variation for small deviation of the factors. In this study, the bifurcation theory is introduced for the finite element analysis of wrinkling initiation and growth, All the above mentioned factors are conveniently considered by finite element method. The finite element formulation is based on the incremental deformation theory and elastic-plastic material modeling. The finite element analysis is carried out using the continuum-based resultant shell elements considering the planar anisotropy of the sheet metal. The proposed method is verified by employing to column buckling problem. And then, the initiation and growth of wrinkling in deep drawing of cylindrical cup are analyzed.
-
The material properties and forrnabilities of tailored blanks are evaluated by experimental tests. In the tensile test, the gradient of strength coefficients of the heat affected zone associated with the welded line width represents the quality of a welded part. In the hemispherical dome punching test, the plane strain state of the welded line is observed. In the squared cupping test, the thin side is stretched more than the thick side in the stretch mode, while both sides are similarly stretched in the draw mode. In the 2D draw test, FLCo is measured in a simple manner and the forming defects of the tailored blanks with the same thickness are found.
-
To predict strain distributions and weld line movements in the forming processes of tailored blank sheets, the 2-dimensional finite element formulation is developed. The welding zone is modelled with the several, narrow finite elements. The material properties of weld elements are calculated from those of base metals, based on the experimental evaluation. To verify the finite element formulation developed, the forming process of an autobody door inner panel section is simulated. FEM predictions are compared and showed good agreements with experimental measurements.
-
In this study, the subframe of passenger car is developed by typical analysis and carsh simulations. According this results, energy absorption and barrier froce is very important to control passenger safety and deformation shape. For that purpose, it is most effective to absorb energy more tailor welded blanks(TWB) subframe than non-TWB. The subframe with TWB is simulated, in which reduced stamping parts, weight reduction and cost down.
-
This study is to investigate the effects of warm deep drawing with aluminum sheets of A1050-H16 and A5052-H32 for improving deep drawability. Experiments for procucing circular cups and square cups were carried out for various working conditions, such as forming temperature and blank shape. The limit drawing ratio(LDR) of 2.63 in warm deep drawing of circular cups in case of A5052-H32 sheet, whereas LDR of A1050-H16 is 2.25, could be obtained and the former was 8 times higher than the value at room temperature. The maximum relative drawing depth for square cups of A5052-H32 material was also about 2 times deeper than the depth drawn at room temperature. The effects of blank shape, and temperature on drawability of aluminum materials as well as thickness distribution of drawn cups were examined and discussed.
-
In order to investigate the effects of the variables during the stamping process upon the side wall curl behavior, experiments and finite element analyses were done using a 90 degree draw-bending test. The variables considered were the die radius, the forming speed, the restraint force, the lubrication and the sheet grade. The experiments and simulation conditions were selected according to the design of experiment (DOE) approach. The effects of the restraint force, the lubrication and the forming speed were the same for both high strength and mild steels, but the effects of the die radius on the side wall curl were dependent on the magnitude of the die radius and the sheet grade. A straight side wall was observed for both high strength and mild steels when the die radius was about 2∼3 times of the sheet thickness. It was recommended that the restraint force, the forming speed and the friction be increased in order to reduce the side wall curl.
-
Anisotropy is closely related to the formability of sheet metal and should be considered carefully for more realistic analysis of actual sheet metal forming operations. In order to better describe anisotropic plastic properties of aluminum alloy sheets, a planar anisotropic yield function which accounts for the anisotropy of uniaxial yield stresses and strain rate ratios simultaneously was proposed recently[1]. This yield function was used in the finite element simulations of cup drawing tests for an aluminum alloy 2008-T4. Isotropic hardening with a fixed initial back stress based on experimental tensile and compressive test results was assumed in the simulation. The computation results were in very good agreement with the experimental results. It was shown that the initial back stress as well as the yield surface shape have a large influence on the prediction of the cup height profile.
-
The superplastic deformation behaviors of 7075Al alloy have been characterized experimentally and analyzed by the internal variable theory of inelastic deformation. A simple rheological model including the grain boundary sliding has been used to interpret the superplastic deformation behaviors. A series of load relaxation and tensile tests have been carried out for 7075Al alloy at the various temperatures. The superplastic deformation of 7075Al alloy is confirmed to consist of the grain boundary sliding and accommodating grain matrix defprmation.
-
High temperature deformation behavior of Al85Ni10Y5 alloy extrudates fabricated with amorphous ribbons was investigated at temperature range form 300 to 550
$^{\circ}C$ by torsion tests. Thermal properties of amorphous ribbons as a function of aging temperature was studied by Differential Scanning Calorimetry(DSC). The Al phase crystallite firstly formed in the amorphous ribbons and its crystallization temperature(Tx) was ∼210$^{\circ}C$ . During the processings of consolidation and extrusion, nano-grained structure was formed in the Al85Ni10Y5 alloy extrudates. The as-extrudated Al85Ni10Y5 alloy and the Al85Ni10Y5 alloy annealed at 250$^{\circ}C$ for 1 hour showed the flow curve of DRV(dynamic recovery) during hot deformation at 400-550$^{\circ}C$ . On the other hand, the Al85Ni10Y5 alloy annealed at 400$^{\circ}C$ for 1 hour showed the flow curve of DRX(dynamic recrystallization) during hot deformation at 450-500$^{\circ}C$ . -
High temperature plastic deformation behavior of Al 6061 alloy was characterized by hot torsion test. The Al 6061 alloy deformed continuously in the temperature range of 400∼550
$^{\circ}C$ , and strain rate range of 0.05∼5/sec. The softening mechanism of Al 6061 alloy was dynamic recrystallization and identified by hyperbolic sine law and zener-Hollmon parameter. The evolution of grain size and deformation resistance were calculated by the relationships of deformation variables. -
-
The service life of tools in metal forming process is to a large extent limited by wear, fatigue fracture and plastic deformation. In warm forging processes wear is the predominant factor for operating lives of tools. To predict tool life by wear, Archard's wear model is generally applied. Usually hardness of die is considered to be a function of temperature in Archard's wear model. But hardness of die is a function of not only temperature but also operating time of die. To consider softening of die by repeated operations, it is necessary to express hardness of dies by a function of temperatures and operating time. By experiment of reheating of dies, die softening curves were obtained. Finally modified Archard's wear model in which hardness of die was expressed as a function of main tempering curve was proposed.
-
In bulk metal forming processes prediction of tool life is very important for saving production cost and achieving good material properties. Generally the service life of tools in metal forming process is limited to a large extent by wear, fracture and plastic deformation of tools. In case of hot and warm forging processes, tool life depends on wear over 70%. In this study finite element analyses are applied to warm forging and hot forging by adopting suggested wear model. By comparision of simulation and real profile of die, suggested model is verified
-
In this study, Al-Ni-Mm alloy has been produced by a gas atomization technique and consolidated by a powder extrusion method. The powders showed mixed structures of amorphous, fcc-Al phases and intermetallics. Each phase shows different size and quantity with different size of the powders due to the higher cooling rate of the finer powders. Because of the difference of the microstructure, the powders with the different size show differences of the mechanical properites of the powders and extrudates.
-
The semi-solid materials(SSMs) fabricated under electric-magnetic stirring condition are necessary to be applicated in the thixoforging process. The optimal reheating conditions to thixoforging process were investigated with changing the reheating time, holding time, reheating temperatures, capacity, and adiabatic material size. In the case of solid fraction fs=50%, the microstructure of SSM (specimen size:d76X 190) at the condition of the first reheating time 4min, holding time lrnin and reheating temperature 350%, the second reheating time 3min, holding time 3min and reheating temperature 575C, the thlrd reheating time lmin, holding time 2min and reheating temperature 584'C, capacity Q=8.398KW, and adiabatic material size 53mm is obtained with globular microstructure and finest.
-
A derivative based approach to process optimal design in powder forging is presented. The process model, the formulation for process optimal design, and the schemes for the evaluation of the design sensitivity, and an iterative procedure for the optimization are described in detail. The validity of the schemes for the evaluation of the design sensitivity is examined by performing numerical tests. The capability of the proposed approach to deal with diverse process parameters and objective functions is demonstrated through applications to some selected process design problems.
-
A hot forging product in general is produced through buster, blocker and finisher processes. Usually the processes including dies are designed by experienced forging engineers. However, due to the lack of such engineers, it is necessary to develop expert systems with which engineers of little experience can perform the design task. In the present study, an expert system is developed for axisyrnmetric hot steel forgings. It is a rule based system written in Fortran and AutoLISP, operating on a personal computer. In this paper, structures of the system are summarized and capabilities of the system are examined through several examples.
-
Proper design of blocker dies is one of the most important aspect of impression and closed-die forging to achieve adequate metal distribution. Determination of the blocker configuration is a very difficult task and is art in itself, requiring skills achieved only by years of extensive experience. To save the cost and time of blocker design, many methods using computer were proposed. In this research, low pass filter method proposed by Oh etc. was applied to blocker die design of spoiler support, part of aircraft and plasticine model experiment of closed die forging of spoiler support was accomplished to verify the validity of the blocker designed.
-
An integrated finite element computer simulator is presented for the prediction of three dimensional heat transfer and metal flow occurring in the strip, and heat transfer and thermo elastic phenomena occurring in the rolls in 4 high mill hot strip rolling. Basic finite element models are described, with emphasis on combining each model to deal rigorously with the coupled aspect of the thermo-mechanical behaviors of the rols and strip through an iterative solution procedure. A series of process simulation are carried out to investigate the effect of various parameters under the actual process conditions. The results are shown and discussed.
-
Finite Element Analysis of 3 Dimensional Steady State Deformation in Multi-stand Rod and Bar RollingCaliber design in bar and rod rolling depends on the designer's experience, which in general is acquired through costly trial-and-error process. As a prerequisite for developing a scientific approach to caliber design, we present a finite element model to simulate 3-D deformation of bars and rods occurring in multi-pass sequence. The results are compared with measurements obtained from POSCO for to assess the solution accuracy. The comparison shows that the simulation results agree well experiments.
-
The continuous casting process has been adopted increasingly in recent years to save both energy and labor. It has experienced a rapid development in the production of semi-finished steel products, replacing the conventional route of ingot casting plus rolling. To achieve this good merit, however, more studies about a heat transfer mechanism between roll and slab are needed. So this paper shows the results of the deformation behavior of steel cast slabs, which are about the solidification and heat transfer. This study is used to prevent internal cracks of a slab in a bending and unbending zone. The value of moving strand shell bulging between two supporting rollers under ferrostatic pressure and slab-self weight has been computed in terms of creep and elastic-plasticity. The high strand distributions in solidified shell undergoes a series of bulging are calculated with boundary condition a very closed to continuous steel cast slabs productions.
-
VCR is a back-up roll with a special contour which leads to the length of the contact line between back-up roll and work becones self adjustable in accordance with the width of the strip. The simulation of a finite element model and the on-line test at production mill demonstrate that the VCR roll may keep the crown of the roll gap relatively stable, and at same time, permit the rolling pressure to be adjusted over a wider range, and increase the effect of work roll bending on the roll gap. The VCR rolls have been successfully used at the first stands of two largest cold rolling mills in China, and on-line test has been done at a wide hot strip finishing train. The use of VCR roll has created favorable conditions for subsequent rolling passes and the achievement of better flatness quality.
-
Stainless steel sheets are widely used to produce electrical appliances. But there are various problems occured in forming stainless steel sheets such as scratch, local fracture, earing. So the productivity of electrical appliances made of stainless steel sheets is decreased. And it is very important to improve the formability of stainless steel sheets. In this study, rectangular cup drawing tests have been carried out to obtain optimum process parameters for improving the formablity of stainless steel sheets. In the tests, selected process parameters are materials of dies and punches, lubricating conditions, and blank holding force. From the test results, we suggest the appropriate conditions to be applicable to the actual manufacturing processes.
-
This paper describes a research work of developing a computer-aided design and manufacturing (CAD-CAM) of irregular shaped sheet metal product for blanking or piercing and bending operation. An approach to the system is based on the knowledge-based rules. Knowledge for the system is formulated form plasticity theories, experimental results and the empirical knowledge of field experts. This system has been written in AutoLIST on the AutoCAD and in customer tool kit on the SmartCAM with a personal computer and is composed of nine modules. the system is designed by considering several factors, such as material and thickness of product, complexities of blank geometry and punch profile, diameter and material of a wire, and availability of press. This system is capable of unfolding a formed sheet metal to give flat pattern and automatically account for the adjustment of bending allowances to match tooling requirements by checking dimensions and generating NC data automatically according to drawings of die-layout module. Results carried out in each module will provide efficiencies to the designer and the manufacture of blanking or piercing and bending die in this field.
-
This article is aimed primarily at establishing a process planning method for complex circular shells. For the deep drawing of complex shaped shell, the optimum process design is required to reduce the trial cost, improve the quality, increase the productivity and shorten the delivery. The present approach which is related to the optimum process planning is based on the empirical knowledge through trial and error in the industrial field. In order to check the validity and the effectiveness of proposed work, a sample process design has been applied to the multi-stepped deep drawing of complex shell considering the process variables such as drawing rate, radius and blank development. In particular, the difference between the limiting drawing rate and the optimum drawing rate has been discussed and has been shown the usefulness of present suggestion.
-
In the present study, a method for measuring the relative density by the hardness measurement was proposed for sintered metal powder compacts. It is based on the indentation force equation, by which the relative density is related with the hardness, that was obtained by the finite element analysis of rigid-ball indentation on sintered metal powder compacts. For verifying the method, it was applied to prediction of density distributions in sintered and sintered-and-forged Fe-0.5%C-2%Cu powder compacts.
-
Tracings streamlines in global coordinate, especially with finite element mesh, requires much computation due to C0 continuity of velocity field. In this study, a new approach is presented for the determination of streamlines from velocity field obtained by FE analysis. It is shown that amount of calculation can be drastically reduced and boundary of element can be easily treated. The approach is applied to the problem of free surface of deforming workpieces in shape rolling.
-
Semi-solid forging can be applied in industry only with enough knowledge of the effects of the forming parameters related with the process and their exact control which can be obtained by empirical or numerical methods. In the current study, the effects of process variables on semi-solid forging are discussed based on mainly numerical results. Die preheating temperature, initial solid fraction of the workpiece, and die velocity were selected as process variables, and numerical analyses using a rigid-thermoviscoplastic finite element approach that considered the release of latent heat due to phase change were carried out. In the analyses, a proposed flow stress material characterization and a solid fraction updating algorithm were employed. The obtained results from numerical analysis are discussed and are compared with some experimental observations.
-
A new blank design method is proposed to predict the optimum initial blank shape in the sheet metal forming process. The rollback method for blank shape design takes the difference between final deformed shape and target contour shape into account. Based on the method, a computer program composed of blank design module, FE-analysis program and mesh generation module is developed. The rollback method is applied to square cup drawing process with the flange of unifiorm size around its periphery to confirm its validity. The optimum initial blank shape is obtained from an arbitrary square blank after three modifications. Good agreements are recognized between the numerical results and the published results for initial blank shape and thickness strain distribution. The optimum blank shape for two parts of automobile sub-frame is designed. The thickness distribution and the level of punch load is improved. Also, the method is applied to design the weld line in the tailor-welded blank. It is concluded that the rollback method is an effective and convenient method for an optimum blank shape design.
-
In this study, a method is presented which can be used to measure the fiber orientation distribution for thickness direction during injection molding using image processing. The intensity method in used for measuring the distribution. And the effects of fiber content, injection molding condictions on the orientation function are also discussed.
-
Unlike the drawing of round section from round bar, the shaped drawing like polygonal section is known to have influence not only drawing stress but also comer filling. Therefore, this study analyze the drawing process of suqare rod from round bar using nonsteady state rigid-plastic FEM. To investigate effects of process variables of the drawing process of square rod from round bar, FE-simulations with variety of reduction in area and semi-die angle for a given frictional condition have been conduction. By this results, it has to suggest optimal process condition on the drawing stress and the comer filling. In addition, it has determined forming limit considering necking and bulging.
-
A kinematically admissible velocity field is developed for the analysis of twisting of extruded products. The twisting of extruded product is caused by the linearly increased rotational velocity from the center on the cross-section of the workpiece at the die exit. In the analysis, the rotational velocity in angular direction is assumed by the multiplication of radial distance and angular velocity. The angular velocity is zero at the die entrance and is increased linearly by axial distance from die entrance. The increase rate of angular velocity is determined by the minimization of plastic work. The results of the analysis show that the angular velocity of the extruded product increase with the die twisting angle and the aspect ratio of product and friction condition and reduction area and show that angular velocity increases with the decreases in die length.
-
Determination of Flow Stress of Semi-Solid A12024 Alloy by Backward Extrusion and Upper Bound MethodAnalytic and experimental methods have been used for the characterization of flow behavior of semi-solid Al2024 alloy. Backward extrusion experimnet was chosen to avoid the crack on the unconstrained surface. The material constants for the flow stress by the upper bound technique that agreed with experimental results were determined. The various material constants obtained for al temperature range above the solidus temperature have been fitted and represented in the function of temperature and solid fraction. The obtained result has good agreement only in the high solid fraction.
-
The failure of die often occurs as a result of growth of microcracks - referred as a brittle damage. In this study, an analysis of brittle damage evolution cupled with elastic finite element analysis of die deformation is presented. A local transformation from the tractions of a workpiece mesh to those of a die mesh is developed. The brittle damage is defined as a vector considering the shape of common microcracks in the brittle metals and the damage function suggested by Krajcinovic is utillized. Applications of the proposed model to modeling damage evolution in the extrusion die and forging die are given and the characteristics of brittle damage evolution in die are in detail examined.
-
Non-heat-treated type material has been investigated for formability compared to heat-treated material. It is very important in automation of metal forming, since it has difficulties of controlling heat treating system by the computer and has bottle neck problem related with heat treatment. In this paper, we have concerned about mechanical properties of non-heat-treated material after the forging. To compare the characteristics between heat-treated material and non-heat-treated material, tensile, compression and fatigue test has been performed. Considering results of mechanical properites of non-heat-treated material, it can replace heat-treated material. Therefore non-heat-treated material may be applied to cold forging.
-
This study presents steady-state finite element analysis of three-dimensional hot extrusion of sections through square dies. The objective of this study is to develop a steady-state finite element method for hot extrusion through square dies, and to provide theoretical basis for the optimal die design and process control in the extrusion technology. In the present work, steady-state assumption is applied to both analyses of deformation and temperature. The analysis of temperature distribution includes heat transfer. Convection like element is adopted for the heat transfer analysis between billet and container, and also billet and die. Distributions of temperature, effective strain rate, velocity and mean stress are discussed to design extrusion die effectively.
-
This study is concerned with the optimum blank design which is able to minimize earing phenomena. A new analytic method is proposed to determine the optimum blank shape only using the tension test and standard deep drawing tests. Introducing a dimensionless parameter related to the earing and using a Fourier analysis, the optimum blank shape can be obtained by R-value and the tested results. The theoretical results by the proposed method are good agreement with the experimental results through several deep drawing tests using steel as working materials.
-
Effects of the anisotrpy due to the initial textures in the plane sheet on plane strain punch stretching has been investigated. In this study, the anisotropy from textures in the sheet is incoporated into the finite element process model by combining the theory of crstal plasticity. Three different textures such as random texture, plane strain compression texture and cube texture are considered. Variations of puch loads as well as thickness distributions of the sheets with three different initial textures are investigated.
-
In the present study, domain decomposition using the substructuring method is developed for the computational efficiency of the finite element analysis of metal forming processes. In order to avoid calculation of an inverse matrix during the substructuring procedure, the modified Cholesky decomposition method is implemented. As obtaining the data independence by the substructuring method, the program is easily parallelized using the Parallel Virtual Machine(PVM) library on a workstation cluster connected on networks. A numerical example for a simple upsetting is calculated and the speed-up ratio with respect to various domain decompositions and number of processors. Comparing the results, it is concluded that the improvement of performance is obtained through the proposed method.
-
The kinematically admissible velocity field is developed for the shapes of dead metal zone and the curving velocity distribution in the eccentric plane dies extrusion. The shape of dead metal zone is defined as the boundary surface with the maximum friction constant between the deformable zone and the rigid zone. The curving phenomenon in the eccentric plane dies is caused by the eccentricity of plane dies. The axial velocity distribution in the plane dies is divided in to the uniform velocity and the deviated velocity. The deviated velocity is linearly changed with the distance from the center of cross-section of the workpiece. The results show that the curvature of products and the shapes of the dead metal zone are determined by the minimization of the plastic work and that the curvature of the extruded products increases with the eccentricity.
-
The twisting and the bending of extruded product are caused by the shapes of products and by the shapes of die surfaces and by the shapes of die land. Because the elliptical shape and the circular shape of the extruded product have the symmetry line of cross-section area, the twisting and the bending of product has not occurred. But the analysis by the DEFORM-3DTM show that the twisting and the bending of extruded product can be occurred by the twisting of the twisting of the die land and by the curving of the die land. The results by the analysis show that the twisting angle of the extruded procduct increases by the twisting angle of the die land and the curvature of the extruded products increases by the radius of bending of the die land.
-
Induction heating is commonly used in process heating prior to metal working and in heat treationg, welding, and melting. For an analysis of induction heating system, it is necessary to calculate eddy currents in conductors induced by a source current. This study examines the use of the Impedance Boundary Condition for the reduction of the field problem encountered in the computation of eddy currents in non-magnetic and magnetic conductors with small penetration depths to a simpler exterior problem. The electric field intensities on the conductor surfaces computed by using the IBC are compared with the values obtained from the full region solution (i.e. without the use of IBC) and those agree well with the latter.
-
Nickel Plating improves on the corrosion resistance of materials in acid and moisture environment. In this study, we investigated the surface morphology, XRD patterns and pole figures of the various types of Ni electrodeposits. The texture of Ni electrodeposits changed from <100> to <111> through <110> with increasing the temperature of electrolyte and the concentration of nickel ion. The texture of Ni electrodeposits changed from <100> to <100> after annealing. Also the <110> texture changed to the <√310> texture after annealing.